2 layers72 × 24 mm
Adin1100 podl
dragonlock2/kicadboards
Offsite backup for the miscellaneous KiCad boards that don't fit elsewhere
125 parts14Apache-2.0
4 layers100.5 × 87.7 mm
Lichtstab
kilimnik/lichtstab- Size
- 100.5 × 87.7 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 151
- Nets
- 141
- Pads
- 583
- Tracks, vias
- 1,154, 304
- Pours
- 8
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 19 Jun 2024
- Updated
- 27 Jun 2024
Overview
Lichtstab is an open-source printed circuit board by kilimnik, from the kilimnik/lichtstab repository on GitHub. It is a 4-layer board of 100.5 × 87.7 mm with 151 parts on 141 nets, routed with 1,154 tracks and 304 vias.
It is built around the DP1435-12V, ESP32-WROOM-32UE-N8 and RTL8201F-VB-CG, with the TPS54331DR-JSM, CH224K and GXHTC3C among its other parts. Its parts include 47 capacitors, 46 resistors, 15 ICs, 11 diodes and 5 inductors. It belongs with the ESP32 boards of this library.
Main components
12
DP1435-12V
--25℃~+85℃ 37V~57V Power over Ethernet Module Short-Circuit Protection、Thermal Protection Yes - Ethernet Modules ROHSSDAPOEthernet Modules
ESP32-WROOM-32UE-N8
模块-40℃~+85℃ -92dBm 112mA 2.4GHz 20dBm 239mA 3V~3.6V Bluetooth4.2 ESP32-DOWD-V3、ESP32-DOWDR2-V3 UART、SDIO、SPI、I2C、GPIO、ADC、I2S、DAC、Ethernet、TWAI SMD,19.2x18mm WiFi Modules ROHSEspressif SystemsWiFi Modules
RTL8201F-VB-CG
QFN-32-EP(5x5)0℃~+70℃ 1 10BASE-T、100BASE-TX 10Mbit/s、100Mbit/s 3.3V MII、RMII PHY Transceiver QFN-32-EP(5x5) Ethernet Transceivers ROHSRealtek SemiconEthernet Transceivers
TPS54331DR-JSM
SOP-8-40℃~+125℃ 1 2mA 3A 4.5V~40V 400kHz Adjustable Buck Built-in No Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting Step-down type SOP-8 DC-DC Converters ROHSJSMSEMIDC-DC Converters
CH224K
ESSOP-10-150mil-1mm-40℃~+90℃ 100W 4V~30V 5V、9V、12V、15V、20V Overvoltage Protection、Thermal Protection PD 3.0 Power Receiver Controller ESSOP-10-150mil-1mm USB PD ROHSWCH (Nanjing Qinheng Microelectronics)USB Converters
GXHTC3C
DFN-6(2x2)-45℃~+130℃ 0%RH~100%RH 1.6V~5.5V 16bit 45uA I2C ±0.3℃ ±3%RH DFN-6(2x2) Temperature and Humidity Sensor ROHSGXCASTemperature And Humidity Sensor
HL2304
SOT-23-55℃~+150℃ 1 N-channel 1.5V 17pF 1W 234pF 3.6A 30V 37mΩ@10V、57mΩ@4.5V 6.08nC@10V N-Channel SOT-23 MOSFETs ROHShongjiachengMOSFETs
LIS2DH12
LGA-12(2x2)-40℃~+85℃ 0.2KB 1.71V~3.6V 500nA 8bit、10bit、12bit Accelerometer Motion event detection SPI、I2C X,Y,Z ±16g LGA-12(2x2) Accelerometers ROHSSTMicroelectronicsAccelerometers
2.54-2*4P立贴针
SMD,P=2.54mm-55℃~+105℃ 2 2.54mm 2.54mm 2.5mm 2x4P 3A 6mm 8P Black Pin Header Surface Mount,Vertical SMD,P=2.54mm Pin Headers ROHSBOOMELEPin Headers
SS34
SMA(DO-214AC)-55℃~+125℃ 3A 40V 500uA@40V 550mV@3A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky Diodes
CR5040-150M
SMD,5x5mm15uH 2A 2A 86mΩ ±20% SMD,5x5mm Power Inductors ROHSCeaiyaPower Inductors
TS-1187A-B-A-B
SMD-4P,5.1x5.1mm-30℃~+85℃ 1.5mm 1.6N 100,000 cycles 12V 5.1mm 5.1mm 50mA Gold No Round Button SPST Surface Mount,Vertical Without Bracket SMD-4P,5.1x5.1mm Tactile Switches ROHSXKB ConnectionTactile Switches
Parts
151| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | 100nF | Capacitor_SMD:C_0603_1608Metric | C3, C13, C14, C15, C16, C17, C18, C20, C33, C34, C35, C41, C42, C43, C47 |
| 11 | 220Ω | Resistor_SMD:R_0603_1608Metric | R3, R4, R15, R18, R22, R24, R29, R32, R34, R39, R43 |
| 10 | 47uF | Capacitor_SMD:C_1206_3216Metric | C1, C9, C10, C12, C32, C36, C37, C38, C40, C46 |
| 9 | 10kΩ | Resistor_SMD:R_0603_1608Metric | R1, R2, R12, R20, R30, R31, R35, R37, R42 |
| 5 | 2.54-2*4P立贴针 | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical_SMD | H2, H3, H4, H5, H6 |
| 5 | 75Ω | Resistor_SMD:R_0603_1608Metric | R5, R6, R7, R8, R23 |
| 4 | 10nF / 100V | Capacitor_SMD:C_0603_1608Metric | C5, C6, C7, C8 |
| 4 | 22uF | Capacitor_SMD:C_1210_3225Metric | C21, C22, C23, C24 |
| 4 | 49.9Ω | Resistor_SMD:R_0402_1005Metric | R9, R10, R11, R13 |
| 4 | HL2304 | Package_TO_SOT_SMD:SOT-23 | U6, U10, U13, U14 |
| 4 | LED | LED_SMD:LED_0805_2012Metric | D3, D4, D7, D12 |
| 3 | 1kΩ | Resistor_SMD:R_0603_1608Metric | R19, R33, R44 |
| 3 | 2.49Ω | Resistor_SMD:R_0603_1608Metric | R14, R16, R17 |
| 3 | 4.7kΩ | Resistor_SMD:R_0603_1608Metric | R40, R41, R46 |
| 3 | SS34 | Diode_SMD:D_SMA | D2, D10, D11 |
| 2 | 10pF | Capacitor_SMD:C_0805_2012Metric | C30, C31 |
| 2 | 169kΩ | Resistor_SMD:R_0603_1608Metric | R25, R27 |
| 2 | 1N4001 | Diode_SMD:D_SOD-123F | D8, D9 |
| 2 | 2.7nF | Capacitor_SMD:C_0805_2012Metric | C28, C29 |
| 2 | 22nF | Capacitor_SMD:C_0603_1608Metric | C25, C39 |
| 2 | 69.8kΩ | Resistor_SMD:R_0603_1608Metric | R26, R28 |
| 2 | 8.2nF | Capacitor_SMD:C_0603_1608Metric | C26, C27 |
| 2 | AP74700QW6-7 | Package_TO_SOT_SMD:SOT-23-6 | U5, U9 |
| 2 | CR5040-150M | Library:IND-SMD_L5.0-W5.0_SWPA5040S | L3, L4 |
| 2 | TPS54331DR | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U7, U8 |
| 2 | TS-1187A-B-A-B | Library:SW-SMD_4P-L5.1-W5.1-P3.70-LS6.5-TL-2 | SW1, SW2 |
| 2 | ZMM3V3-M | Diode_SMD:D_MiniMELF | D5, D6 |
| 1 | 1.91kΩ | Resistor_SMD:R_0603_1608Metric | R38 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric | C11 |
| 1 | 1nF / 2KV | Capacitor_SMD:C_1206_3216Metric | C4 |
| 1 | 1uF | Capacitor_SMD:C_0805_2012Metric | C19 |
| 1 | 2.49kΩ | Resistor_SMD:R_0603_1608Metric | R45 |
| 1 | 220nF | Capacitor_SMD:C_0603_1608Metric | C44 |
| 1 | 24kΩ | Resistor_SMD:R_0603_1608Metric | R21 |
| 1 | 3.16kΩ | Resistor_SMD:R_0603_1608Metric | R36 |
| 1 | 3.3µH / 3.1A | Inductor_SMD:L_Changjiang_FNR5030S | L5 |
| 1 | 330u / 25V | Capacitor_SMD:CP_Elec_8x10.5 | C45 |
| 1 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C2 |
| 1 | 50MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | X1 |
| 1 | AO3407A | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | B1601S | Library:SMD-16_L12.7-W7.0-P1.27-LS9.5-BL | L1 |
| 1 | CH224K | Library:ESSOP-10_L4.9-W3.9-P1.0-LS6.0-TL-EP | U4 |
| 1 | DP1435-12V | Library:PWRM-TH_DP1435-XX | U2 |
| 1 | ESP32-WROOM-32UE-N8 | RF_Module:ESP32-WROOM-32UE | U1 |
| 1 | GXHTC3C | Library:DFN-6_L2.0-W2.0-P0.50-TL-EP | U15 |
| 1 | HCB1608KF-501T20 | Inductor_SMD:L_0603_1608Metric | L2 |
| 1 | LIS2DH12 | Package_LGA:LGA-12_2x2mm_P0.5mm | U11 |
| 1 | LIS2MDLTR | Library:LGA-12_L2.0-W2.0-P0.50-BL | U12 |
| 1 | LOGO | TheBrutzlers_Lib:approved_theBrutzler | G*** |
| 1 | MIKROBUS_HOST_CONN | mikroBUS:MIKROBUS_HOST_CONN | CON1 |
| 1 | MIKROBUS_MODULECONN | mikroBUS:MIKROBUS_MODULE_CONN | CON2 |
| 1 | MLT-8530 | Library:BUZ-SMD_4P-L8.5-W8.5-P8.50-BR | BUZZER1 |
| 1 | RJ45_LED_Shielded | Library:RJ45-TH_R-RJ45R08P-C000 | J1 |
| 1 | RTL8201F-VB-CG | Package_DFN_QFN:TQFN-32-1EP_5x5mm_P0.5mm_EP3.4x3.4mm_ThermalVias | U3 |
| 1 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP1 |
| 1 | TYPE-C16PIN | Library:USB-C-SMD_TYPE-C16PIN | USB1 |
| 1 | ~ | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical_SMD | H1 |
The 141 most common of 151 parts.
Similar boards
- 4 layers52.5 × 80 mm
- 2 layers75.1 × 100 mm
- 6 layers128 × 117.8 mm
FPGA DevBoard
Benny-Chippers/Enchanted_Rocks
The dev board PCB for the MacroController project
301 partsMIT - 2 layers99.8 × 49.8 mm
LedArrayDemo
radex/radmatrix
Tiny modular LED matrix. NOTE: Moved to https://code.hackerspace.pl/radex/radmatrix
453 parts2 - 2 layers54 × 85.6 mm
Board43
smartbank-inc/Board43
Board43 is an RP2350A-based microcontroller development board. Flash PicoRuby or your favorite firmware and start hacking.
583 parts30 - 2 layers42 × 66 mm
Wafflehw rev0.1
Jankyneering/Waffle_hw
Hardware designs for Waffle, a compact Pager and general RF multitool.
42 parts2GPL-3.0 - 2 layers65 × 45 mm
Questions
How big is the Lichtstab PCB?
It measures 100.5 × 87.7 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Lichtstab use?
151 parts, built around the DP1435-12V, ESP32-WROOM-32UE-N8, RTL8201F-VB-CG and TPS54331DR-JSM. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Lichtstab KiCad files?
From the kilimnik/lichtstab repository on GitHub, at the commit this page was made from: the board is pcb/Lichtstab.kicad_pcb and its schematic pcb/1_P1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Lichtstab design in my own project?
Its repository states no licence, so its author keeps all rights: ask kilimnik before reusing the design.