Skip to the content
2 layers9.7 × 9.8 mmG6 Mag Charger, the printed circuit board in 3D

Board and steps for creating a rechargeable Dexcom device.

Size
9.7 × 9.8 mm
Copper layers
2
Thickness
0.6 mm
Parts
13
Nets
9
Pads
30
Tracks, vias
65, 12
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
8 Aug 2020
Updated
19 Oct 2020

Overview

G6 Mag Charger is an open-source printed circuit board by kicker22004, from the kicker22004/Dexcom-G6-Mag-Recharge repository on GitHub. It is a 2-layer board of 9.7 × 9.8 mm with 13 parts on 9 nets, routed with 65 tracks and 12 vias.

It is built around the BAT54SLT1G. Its parts include 3 resistors, 3 diodes, 3 connectors and 2 capacitors. It belongs with the power boards of this library.

Main components

1

README

README.md

Dexcom-G6-Mag-Recharge-

Rechargeable Dexcom board and steps

WARNING!!!!.

This is a DIY project that you will attach a LIPO battery to your body, This comes with risks and as such if you decide to build one for yourself you are doing so at your own risk and I will not be held responsible for any and all injuries or damages to you or your Transmitters.

Ok with that out of the way I have several test users that have had great success using their devices and figured it's time to share. There are a lot of teardown video's out there for removing the battery from your Dexcom device so please look around. There are a few differences in my design in the fact that we will be opening up the rear of the device and creating space for the battery. This will require patients, skill, and a bit of luck.

Parts Required:

  • PCB (Link)
  • 3.7V 30mAh lipo (Part Number 301012)
  • MCP73831T-2 SOT23
  • 2x - 10uf 0402
  • Green LED 0402
  • Red LED 0402
  • 2x - 470k Resistor 0402
  • 10k Resistor 0402
  • BAT54SLT1G SOT-23
  • Magnetic Connector (8MM)

Resources:

I will update this as I have time to include where you can get cables and parts, But for now the parts can be sourced on ebay,digikey,mouser and i'm sure other locations. I'll also attempt to build a wiki for this project but that will come with intrest and time.

Helpful Tools:

  • Reflow station or Reflow Oven
  • My reflow station was cheap (858D+ 220V Hot Air Soldering ReWork Station)

A Stencil for the pcb!!, not required but super useful!

I ordered mine with the pcb from Jlcpcb.com

  • A Digital Microscope. Mine was also cheap (Andonstar ADSM302)

  • Soldering Iron for the wires, Magnetic connector and attaching the battery. Mine is a simple TS100 iron.

Donation:

Never required or requested but always appreciated :)

paypal

Parts

13
QtyValueFootprintReferences
210ufCapacitors_SMD:C_0402C1, C2
2470Resistors_SMD:R_0402R1, R2
110kResistors_SMD:R_0402R3
1BAT54SLT1GTO_SOT_Packages_SMD:SOT-23D3
1Batt +footprints:G6 PadP1
1GNDfootprints:G6 PadP3
1LED (Green)LEDs:LED_0402D2
1LED (RED)LEDs:LED_0402D1
1MCP738312TO_SOT_Packages_SMD:SOT-23-5M2
1MagneticConnectorfootprints:Magnetic PortM1
1Trans +footprints:G6 PadP2

Similar boards

  • 4 layers130 × 25 mmCurrent sense, the printed circuit board in 3D

    Current sense

    westonb/little-bee-B1

    A high performance current & magnetic field probe

    113 parts331CC-BY-SA-4.0
  • 4 layers138.2 × 200.4 mmHV servo drive v1, the printed circuit board in 3D

    HV servo drive v1

    ExcessiveMotion/drive-hardware

    383 parts175CERN-OHL-W-2.0
  • 8 layers64 × 56 mmPS GAN-60W, the printed circuit board in 3D

    PS GAN-60W

    jonahsaunders/planar-studio

    KiCad extension for the copper you can't buy as a part — design planar inductors, transformers, PCB motor stators, filters, and antennas, with electrical modeling and direct write-back to your board.

    89 parts4MIT
  • 2 layers90 × 85 mmMultiBench, the printed circuit board in 3D

    MultiBench

    M-Mrk/MultiBench

    A bench multimeter with the usual functions, but also with usb connectivity to log, stream and monitor readings.

    87 parts1
  • 2 layers120 × 49 mmSensor hat, the printed circuit board in 3D

    Sensor hat

    mikedahlgren/Pool-Controller

    This runs a pool from a Waveshare ESP32-S3-RELAY-6CH and the PoolVeras sensor hat plugged onto its Pico headers.

    69 parts
  • 2 layers180 × 80 mmProyecto0.1V, the printed circuit board in 3D

    Proyecto0.1V

    UTN-FRBA-2026-PF-EE-GP10/mpp_sdk

    ☀️ MPP simulation and validation framework

    168 partsMIT

Questions

How big is the G6 Mag Charger PCB?

It measures 9.7 × 9.8 mm and has 2 copper layers, 0.6 mm thick.

What parts does the G6 Mag Charger use?

13 parts, built around the BAT54SLT1G. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the G6 Mag Charger KiCad files?

From the kicker22004/Dexcom-G6-Mag-Recharge repository on GitHub, at the commit this page was made from: the board is Kicad Folder/G6 Mag Charger V6/G6 Mag Charger.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the G6 Mag Charger design in my own project?

Its repository states no licence, so its author keeps all rights: ask kicker22004 before reusing the design.