2 layers68.6 × 66 mm
4 layers129.5 × 115.6 mm
Pixy-68000
kekyo/Pixy3My own Single-Borard-Computer projects.
- Size
- 129.5 × 115.6 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 94
- Nets
- 158
- Pads
- 648
- Tracks, vias
- 3,590, 778
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 29 Oct 2023
- Updated
- 6 May 2025
Overview
Pixy-68000 is an open-source printed circuit board by kekyo, from the kekyo/Pixy repository on GitHub, published under the Apache-2.0 licence. It is a 4-layer board of 129.5 × 115.6 mm with 94 parts on 158 nets, routed with 3,590 tracks and 778 vias.
It is built around the ATMEGA328P-AU, LCMXO2-640HC-4TG100I and MC68SEC000FU20, with the CH340N and IS61WV5128BLL-10TLI among its other parts. Its parts include 29 capacitors, 25 resistors, 10 connectors, 9 ICs and 9 diodes. It belongs with the fPGA and programmable logic and computers and single-board computers boards and the AVR (ATmega, ATtiny) and FPGA and CPLD boards of this library.
Main components
5
ATMEGA328P-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
LCMXO2-640HC-4TG100I
TQFP-100(14x14)-40℃~+100℃ 18432bit 2.375V~3.465V 640 78 80 MachXO2 Supports hot swap TQFP-100(14x14) Programmable Logic Device (CPLDs/FPGAs) ROHSLatticeProgrammable Logic Device (CPLDs/FPGAs)
MC68SEC000FU20
QFP-64(14x14)0℃~+70℃ 20MHz 32 Bit External External Others QFP-64(14x14) Microcontrollers (MCU/MPU/SOC) ROHSMOTOROLAMicrocontrollers (MCU/MPU/SOC)
CH340N
SOP-8-20℃~+70℃ 1 2Mbps 3.3V、5V USB 2.0 USB to serial SOP-8 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB Converters
IS61WV5128BLL-10TLI
TSOPII-44-10.2mm-40℃~+85℃ 10mA 10ns 2.4V~3.6V 45mA 4Mbit Auto power-down function Parallel Port (Parallel) TSOPII-44-10.2mm SRAM ROHSISSISRAM
README
README.mdPixy - Single board computer projects
What is this?
My owned single board computer projects.
Pixy-68000
- Motorola MC68SEC000-20 (Static low-powered m68k arch.)
- ATMEL AVR ATMega-328PB
- Co-processor for 7segLEDs, LEDs, switches and serial interface.
- LATTICE MachXO2 LCMXO2-640
- Bus controller, captured all signals from the CPU.
- SRAM 1MB (512kbit * 2)
- Flash PROM 1MB (512kbit * 2, PLCC)
Assembled (Pixy-68000-0):
Pixy-mega128
- ATMEL ATMega128-16AU (Simplest 48+ GPIO)
- Enabled Arduino IDE with MegaCore.
Assembled (Pixy-mega128-0):
Pixy-mega128-sdram-hat
- SDRAM: ELPIDA EDS1216AGTA (16MB: 8Mwords * 16bit)
- EXPERIMENTAL circuit board for learning how to use SDRAM.
Assembled (Pixy-mega128-sdram-hat-0):
License
Apache-V2
Parts
94| Qty | Value | Footprint | References |
|---|---|---|---|
| 27 | 0.1u | kekyo:C_0805_2012 | C1, C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23, C24 +11 |
| 14 | 2k | kekyo:R_0805_2012 | R1, R6, R10, R12, R16, R17, R18, R19, R20, R21, R22, R23, R24, R29 |
| 5 | 1.5k | kekyo:R_0805_2012 | R2, R3, R8, R9, R15 |
| 4 | MountingHole_3mm_Pad | MountingHole:MountingHole_3mm_Pad | REF1, REF2, REF3, REF4 |
| 4 | Socket5 | kekyo:PinSocket_1x05_P2.54mm_Vertical | J4, J5, J6, J7 |
| 3 | 1k | kekyo:R_0805_2012 | R7, R11, R14 |
| 2 | 100u | kekyo:CP_Radial_D5.0mm_P2.50mm | C2, C3 |
| 2 | 5.1k | kekyo:R_0805_2012 | R4, R5 |
| 2 | IS61WV5128BLL-10TLI | Package_SO:TSOP-II-44_10.16x18.41mm_P0.8mm | U6, U7 |
| 2 | SST39SF040 | Package_LCC:PLCC-32_THT-Socket | U8, U9 |
| 1 | 10k | kekyo:R_0805_2012 | R13 |
| 1 | ATmega328P-AU | Package_QFP:TQFP-32_7x7mm_P0.8mm | U5 |
| 1 | AVR_ISP | kekyo:PinHeader_2x03_P2.54mm_Vertical | J2 |
| 1 | BUS | Connector_PinHeader_2.54mm:PinHeader_2x25_P2.54mm_Vertical | J8 |
| 1 | CH340N | kekyo:SOP-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | DONE | kekyo:LED_D3.0mm | D3 |
| 1 | HALT | kekyo:LED_D3.0mm | D9 |
| 1 | Header3 | kekyo:PinHeader_1x03_P2.54mm_Vertical | J10 |
| 1 | Header8 | kekyo:PinHeader_1x08_P2.54mm_Vertical | J9 |
| 1 | INIT | kekyo:LED_D3.0mm | D4 |
| 1 | JTAG | kekyo:PinHeader_2x06_P2.54mm_Vertical | J3 |
| 1 | LCMXO2-640HC-4TG100I | kekyo:TQFP100_LAT-M | U4 |
| 1 | LED0 | kekyo:LED_D3.0mm | D5 |
| 1 | LED1 | kekyo:LED_D3.0mm | D6 |
| 1 | LED2 | kekyo:LED_D3.0mm | D7 |
| 1 | LED3 | kekyo:LED_D3.0mm | D8 |
| 1 | MC68SEC000-FU | kekyo:MC68SEC000-FU | U3 |
| 1 | NJM2391 | kekyo:TO-252-3_TabPin4 | U1 |
| 1 | Oscillator | kekyo:Oscillator_SMD_4Pin_7.0x5.0mm_HandSoldering | X1 |
| 1 | POWER | kekyo:LED_D3.0mm | D1 |
| 1 | RUN | kekyo:LED_D3.0mm | D2 |
| 1 | STEP | kekyo:TactSwitch | SW_STEP1 |
| 1 | STEPEN | kekyo:SW_Toggle_3P | SW_STEPEN1 |
| 1 | SW0 | kekyo:TactSwitch | SW0 |
| 1 | SW1 | kekyo:TactSwitch | SW1 |
| 1 | SW2 | kekyo:TactSwitch | SW2 |
| 1 | SW3 | kekyo:TactSwitch | SW3 |
| 1 | SW4 | kekyo:TactSwitch | SW4 |
| 1 | USB | kekyo:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
More from kekyo/Pixy
2- 2 layers35.6 × 53.3 mm
Similar boards
- 4 layers123 × 81 mm
PortableRAM-5V
2tf2294x4g-maker/MacintoshPortable4MB_RAM
A 4MB RAM board for the Macintosh Portable using 5V SRAM
31 parts3CERN-OHL-S-2.0 - 4 layers214 × 142 mm
- 4 layers101.6 × 49.9 mm
SPIFEE
dennowiggle/Retro-PETER
3.3V Retro computer project => FPGA + RCBUS + CPU boards making a custom system.
74 parts4LGPL-2.1 - 2 layers36 × 70 mm
- 2 layers148.5 × 217.7 mm
- 2 layers29 × 48 mm
My design
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
22 parts915 - 2 layers100 × 100 mm
- 2 layers50.5 × 94.7 mm
SwordOfSecretsUSBProd
gili-yankovitch/SwordOfSecrets
To solve the challenge you will need to discover a series of flags, hidden inside the sword. Each one will help you unlock the next step in the challenge, to finally reveal the ultimate secret the sword holds.
16 parts47MIT
Questions
How big is the Pixy-68000 PCB?
It measures 129.5 × 115.6 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Pixy-68000 use?
94 parts, built around the ATMEGA328P-AU, LCMXO2-640HC-4TG100I, MC68SEC000FU20 and CH340N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Pixy-68000 KiCad files?
From the kekyo/Pixy repository on GitHub, at the commit this page was made from: the board is Pixy-68000/Pixy-68000-0/KiCad/Pixy-68000.kicad_pcb and its schematic Pixy-68000/Pixy-68000-0/KiCad/Pixy-68000.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Pixy-68000 design in my own project?
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).