2 layers36 × 70 mm
2 layers148.5 × 217.7 mm
- Size
- 148.5 × 217.7 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 53
- Nets
- 79
- Pads
- 265
- Tracks, vias
- 722, 132
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 9 Jul 2024
- Updated
- 25 Jul 2024
Overview
Name is an open-source printed circuit board by MelonMars, from the MelonMars/AvionicsPCB repository on GitHub. It is a 2-layer board of 148.5 × 217.7 mm with 53 parts on 79 nets, routed with 722 tracks and 132 vias.
It is built around the ATMEGA328P-AU, CH340N and ADXL343BCC, with the TP4057, AO3401A and SS34 among its other parts. Its parts include 16 diodes, 14 resistors, 11 capacitors, 6 ICs and 2 connectors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
6
ATMEGA328P-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
CH340N
SOP-8-20℃~+70℃ 1 2Mbps 3.3V、5V USB 2.0 USB to serial SOP-8 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB Converters
ADXL343BCC
LGA143-Axis, ±2g/±4g/±8g/±16g Digital MEMS AccelerometerAnalog DevicesUncategorised
TP4057
SOT-23-6-40℃~+85℃ 1 25uA 4.24V 4V~6.5V Charging IC Lithium Battery Not supported SOT-23-6 Battery Management ROHSTECH PUBLICBattery Management
AO3401A
SOT-231 P-Channel 14nC@10V 30V 47mΩ@10V、60mΩ@4.5V、85mΩ@2.5V 4A 55pF 645pF 80pF 900mV SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETs
SS34
SMA(DO-214AC)-55℃~+125℃ 3A 40V 500uA@40V 550mV@3A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky Diodes
Parts
53| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | NeoPixel_THT | LED_SMD:LED_WS2812_PLCC6_5.0x5.0mm_P1.6mm | D1, D2, D3, D4, D5, D6, D7, D8 |
| 5 | 100 nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C6, C7, C10 |
| 3 | 1 uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5, C8, C11 |
| 3 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R9, R13, R14 |
| 2 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6, R10 |
| 2 | 12pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3, C4 |
| 2 | 330R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4, R5 |
| 2 | 4.7k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R11, R12 |
| 2 | 5k1 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R3 |
| 2 | LED | Diode_SMD:D_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D12, D13 |
| 1 | 0.1 uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C9 |
| 1 | 100k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | 1k5 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7 |
| 1 | 4k7 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8 |
| 1 | ADXL343 | Package_LGA:LGA-14_3x5mm_P0.8mm_LayoutBorder1x6y | U2 |
| 1 | AO3401A | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | ATmega328P-A | Package_QFP:TQFP-32_7x7mm_P0.8mm | U1 |
| 1 | Arduino_Nano_v3.x | Module:Arduino_Nano_WithMountingHoles | A1 |
| 1 | C8678 | Diode_SMD:D_SMA | D16 |
| 1 | C8678 | Diode_SMD:D_SMC_Handsoldering | D9 |
| 1 | CH340N | Package_SO:SOP-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | Conn_02x03_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J1 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSoldering | Y1 |
| 1 | GREEN | Diode_SMD:D_SMC_Handsoldering | D11 |
| 1 | GREEN | Diode_SMD:D_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D15 |
| 1 | MS5607-02BA | Package_LGA:LGA-8_3x5mm_P1.25mm | U7 |
| 1 | RED | Diode_SMD:D_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D14 |
| 1 | SW_SPST | Button_Switch_SMD:SW_Push_1P1T_XKB_TS-1187A | SW1 |
| 1 | TP4057 | Package_TO_SOT_SMD:TSOT-23-5 | U5 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_Amphenol_12401548E4-2A | J2 |
| 1 | XC6206PxxxMR | Package_TO_SOT_SMD:SOT-23-3 | U6 |
| 1 | YELLOW | Diode_SMD:D_SMC_Handsoldering | D10 |
Similar boards
- 2 layers98.8 × 55.1 mm
H bridge controller
jayanta525/dual-h-bridge
Dual H-Bridge Controller with IRF3205 and IR2104 MOSFET Driver, and with ATMega328P-AU PWM Controller
104 parts5MIT - 2 layers65 × 63.5 mm
- 2 layers69.1 × 56.6 mm
- 2 layers155 × 71 mm
Panel
PHS-SMCS/Falconia-Beacon
Falconia Beacon is an ATTINY816-based, CR2032-powered LED beacon board used to make the Falconia rover visible to the SMCS Pi-in-the-sky satellite.
395 parts - 2 layers61.2 × 35.5 mm
KitchenSink
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
33 parts915 - 4 layers65 × 65.5 mm
- 4 layers60 × 60 mm
Minion
vibsthebot/minion
I'm a mac user, and i love my apple wired headphones. mN phone doesn't have headphone jack and my computer doesn't have micro sd or usb a.
79 parts1
Questions
How big is the Name PCB?
It measures 148.5 × 217.7 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Name use?
53 parts, built around the ATMEGA328P-AU, CH340N, ADXL343BCC and TP4057. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Name KiCad files?
From the MelonMars/AvionicsPCB repository on GitHub, at the commit this page was made from: the board is src/name.kicad_pcb and its schematic Avionics/LED_BLOCK.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Name design in my own project?
Its repository states no licence, so its author keeps all rights: ask MelonMars before reusing the design.