Skip to the content
2 layers74.9 × 20.3 mmRt soldering iron, the printed circuit board in 3D

Soldering iron driver board for Weller RT tips. A work in progress. Firmware in rust.

Size
74.9 × 20.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
126
Nets
66
Pads
337
Tracks, vias
717, 81
Pours
15
Routed
Yes
KiCad
KiCad 4
Created
6 Feb 2018
Updated
30 Jun 2018

Overview

Rt soldering iron is an open-source printed circuit board by kcuzner, from the kcuzner/rt-soldering-iron repository on GitHub. It is a 2-layer board of 74.9 × 20.3 mm with 126 parts on 66 nets, routed with 717 tracks and 81 vias.

It is built around the STM32F031G6U6, MCP6V71U-E/OT and MMA8652FCR1, with the TL431, BAV99WT1G and CUS10F30-TP among its other parts. Its parts include 35 resistors, 26 capacitors, 8 ICs, 7 transistors and 4 diodes. It belongs with the STM32 boards of this library.

Main components

8

README

README.md

RT Soldering Iron

By Kevin Cuzner

NOTE: THIS IS A WORK IN PROGRESS AND MAY NEVER BE COMPLETED

Objective

The Weller RT Soldering Iron Tips are $20-$30 apiece. They are rated to about 55W and many variants come to a very fine point. I had the pleasure of using one of these soldering irons at my university, but the base stations cost several hundred dollars. This project aims to build a "base station" of sorts for these tips so that I can use them without needing to purchase a real base station.

Note that this project has been done before, but I'm doing it myself because reasons.

Concept

  • The Weller RT soldering iron tips have a 1/8" audio plug which has ground, heater, and thermocouple contacts.
  • The heater can be powered from 12V and will consume 55W.
  • Without closed loop control, the soldering iron tip will quickly burn itself up.
  • This driver board will provide 12V and closed loop heater control.
  • The driver board has a 1/8" audio jack on one end and a barrel jack on the other. It is short enough and skinny enough so that it can be mounted directly to the tip and become part of the handpiece, with the barrel jack connecting to the 12V power supply.

Builds

Rev A Deviations

Rev B Deviations

  • 490-14603-1-ND (0.1uF 0402 25V 10% cap) was unavailable. No lead time. Ordered 490-13341-1-ND (0.1uf 0402 25V 20% cap) instead.
  • Accelerometer was out of stock (again...). The other variant used on the LED watch was out of stock too. Did not order this time around.

Parts

126
QtyValueFootprintReferences
1210KResistors_SMD:R_0402R2, R4, R11, R14, R21, R23, R24, R25, R27, R30, R32, R33
100.1uCapacitors_SMD:C_0402C3, C4, C6, C7, C12, C14, C22, C23, C24, C25
71uCapacitors_SMD:C_0402C11, C13, C15, C16, C17, C18, C21
54K7Resistors_SMD:R_0402R1, R8, R15, R16, R17
41KResistors_SMD:R_0402R3, R20, R22, R28
310uCapacitors_SMD:C_0402C8, C9, C10
3FDG6301N_F085TO_SOT_Packages_SMD:SOT-363_SC-70-6Q2, Q5, Q7
20.001uCapacitors_SMD:C_0402C1, C2
2100KResistors_SMD:R_0402R5, R31
216K2Resistors_SMD:R_0402R12, R29
2270Resistors_SMD:R_0402R6, R19
22u2Capacitors_SMD:C_0402C19, C20
249K9Resistors_SMD:R_0402R9, R10
2MMBT3906WT1GTO_SOT_Packages_SMD:SOT-323_SC-70Q4, Q6
2SPRResistors_SMD:R_0402R13, R34
2SPSTrt-soldering-iron:Panasonic_EVQP4SW1, SW2
10Resistors_SMD:R_0402R35
110uCapacitors_SMD:C_0603C5
110uResistors_SMD:R_0805L2
11MResistors_SMD:R_0402R7
122K6Resistors_SMD:R_0402R26
13.6VDiodes_SMD:D_SOD-523D3
1390KResistors_SMD:R_0402R18
14.7uInductors:Inductor_Taiyo-Yuden_NR-30xxL1
1ACS711xEXrt-soldering-iron:12-WFQFNU1
1AP3211TO_SOT_Packages_SMD:SOT-23-6U3
1BARREL_JACKrt-soldering-iron:PJ-069B-SMTJ2
1BAV99WT1GTO_SOT_Packages_SMD:SOT-323_SC-70D2
1CONN_01X04rt-soldering-iron:JST-SH-4J3
1CUS10F30Diodes_SMD:D_SOD-323D1
1Fuse_SmallResistors_SMD:R_0603F1
1IRON_TIPrt-soldering-iron:SJ-3502-SMTJ1
1MCP6V71UTO_SOT_Packages_SMD:SOT-353_SC-70-5U2
1MMA8652FCrt-soldering-iron:10-DFNU6
1MMBT3904TO_SOT_Packages_SMD:SOT-323_SC-70Q3
1PKMCS0909E4000rt-soldering-iron:Murata-PKMCSLS1
1Q_Thyristor_KGATO_SOT_Packages_SMD:SOT-23D4
1SIA483DJ-T1-GE3rt-soldering-iron:PP-SC70-6LQ1
1SPRCapacitors_SMD:C_0402C26
1SSD1306-OLED-I2Crt-soldering-iron:OLED-FPC-I2CU5
1STM32F031Grt-soldering-iron:28-UFQFPNU4
1TL431TO_SOT_Packages_SMD:SOT-363_SC-70-6U7
1TLV1701TO_SOT_Packages_SMD:SOT-353_SC-70-5U8

The 89 most common of 126 parts.

Similar boards

  • 2 layers60.6 × 40 mmATMega328-usb counter, the printed circuit board in 3D

    ATMega328-usb counter

    swharden/USB-Counter

    Open-source USB frequency counter

    39 parts25MIT
  • 4 layers16.5 × 10.9 mmSimple led watch, the printed circuit board in 3D

    Simple led watch

    kcuzner/led-watch

    A miniature ARM-powered LED wristwatch

    183 parts98MIT
  • 4 layers150.3 × 132.3 mmMRIAMP, the printed circuit board in 3D

    MRIAMP

    msayad97/Amplifier

    235 parts1
  • 4 layers31.8 × 27.5 mmProtopoint, the printed circuit board in 3D

    Protopoint

    lab11/polypoint

    Indoor localization based on the DecaWave DW1000.

    57 parts143Apache-2.0
  • 2 layers45 × 45 mmMotor-2, the printed circuit board in 3D

    Motor-2

    mkramar/dizzyrobot

    64 parts13
  • 4 layers33.1 × 64.7 mmNrg3, the printed circuit board in 3D

    Nrg3

    panStamp/kicad

    Kicad projects

    135 parts15GPL-2.0
  • 4 layers38 × 15 mmRuuvilogger reva1, the printed circuit board in 3D

    Ruuvilogger reva1

    ruuvi/ruuvilogger_hw

    You can find RuuviLogger related hardware design files from this repository. Design is almost finished, but not 100% ready. If RuuviLogger project continues, Rev.A version will be probably deprecated.

    93 parts5

Questions

How big is the Rt soldering iron PCB?

It measures 74.9 × 20.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Rt soldering iron use?

126 parts, built around the STM32F031G6U6, MCP6V71U-E/OT, MMA8652FCR1 and TL431. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Rt soldering iron KiCad files?

From the kcuzner/rt-soldering-iron repository on GitHub, at the commit this page was made from: the board is kicad/rt-soldering-iron.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Rt soldering iron design in my own project?

Its repository states no licence, so its author keeps all rights: ask kcuzner before reusing the design.