4 layers39.5 × 27.7 mm
MoveCritic FBTM RF
kapis20/IEEECompetition
This is the repo for IEEE Pitch Competition codes and files storage
12 parts
4 layers39.7 × 27.7 mm
HW MoveCritic KiCad Project
kapis20/IEEECompetitionThis is the repo for IEEE Pitch Competition codes and files storage
- Size
- 39.7 × 27.7 mm
- Copper layers
- 4
- Thickness
- 1.58 mm
- Parts
- 55
- Nets
- 59
- Pads
- 285
- Tracks, vias
- 318, 134
- Pours
- 14
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 22 Dec 2023
- Updated
- 21 Apr 2024
Overview
HW MoveCritic KiCad Project is an open-source printed circuit board by kapis20, from the kapis20/IEEECompetition repository on GitHub. It is a 4-layer board of 39.7 × 27.7 mm with 55 parts on 59 nets, routed with 318 tracks and 134 vias.
It is built around the STM32WB55CEU6, DLF162500LT-5028A1 and BNO086, with the MIC5365-3.3YD5-TR, USBLC6-2P6 and B5819W among its other parts. Its parts include 23 capacitors, 9 resistors, 4 ICs, 3 connectors and 3 inductors. It belongs with the STM32 boards of this library.
Main components
6
STM32WB55CEU6
UFQFPN-48(7x7)UFQFPN-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)
DLF162500LT-5028A1
SMD-4P,1.6x0.8mm-40℃~+85℃ 0.33dB 2.4GHz~2.5GHz 49.2dB 50Ω Low Pass SMD-4P,1.6x0.8mm RF Filters ROHSTDKRF Filters
BNO086
TFLGA-28TFLGA-28 Accelerometers ROHSCEVAAccelerometers
MIC5365-3.3YD5-TR
TSOT-23-5-40℃~+125℃@(Tj) 1 150mA 200uVrms 3.3V 310mV@(150mA) 39uA 5.5V 70dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive TSOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMicrochip TechnologyVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
USBLC6-2P6
SOT-666-6-40℃~+125℃ 150nA 17V 2 3.5pF 5.25V 5A@8/20us 6V ESD IEC 61000-4-2 Unidirectional SOT-666-6 ESD and Surge Protection (TVS/ESD) ROHSSTMicroelectronicsESD And Surge Protection (TVS/ESD)
B5819W
SOD-123-55℃~+125℃ 1.5A 1mA@40V 25A 40V 600mV@1A Standalone SOD-123 Schottky Diodes ROHSMDDSchottky Diodes
README
README.mdIEEECompetition
This is the repo for IEEE Pitch Competition codes and files storage
To run the code, you will need
- Open CV (for windows: py -m pip install opencv-python)
- numpy (for windows: py -m pip install numpy)
- MediaPipe (for windows: pip install mediapipe)
Note: Both squat and lateral raise code are essentially the same except for the angle calculation and display.
Parts
55| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 0u1 | Capacitor_SMD:C_0201_0603Metric | C1, C2, C3, C4, C5, C6, C8, C10, C20, C21, C22 |
| 7 | 4u7 | Capacitor_SMD:C_0201_0603Metric | C7, C9, C11, C16, C17, C18, C19 |
| 3 | Fiducial | Fiducial:Fiducial_1mm_Mask2mm | FID1, FID2, FID3 |
| 3 | MountingHole | MountingHole:MountingHole_2.2mm_M2_DIN965 | H1, H2, H4 |
| 2 | 10p | Capacitor_SMD:C_0402_1005Metric | C12, C13 |
| 2 | 1k | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | 2k2 | Resistor_SMD:R_0402_1005Metric | R7, R8 |
| 2 | 5k1 | Resistor_SMD:R_0402_1005Metric | R3, R4 |
| 1 | 0R | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 0p3 | Capacitor_SMD:C_0402_1005Metric | C15 |
| 1 | 0p8 | Capacitor_SMD:C_0402_1005Metric | C14 |
| 1 | 100p | Capacitor_SMD:C_0201_0603Metric | C23 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R10 |
| 1 | 10n | Inductor_SMD:L_0402_1005Metric | L1 |
| 1 | 10u | Inductor_SMD:L_0805_2012Metric | L2 |
| 1 | 220R | Resistor_SMD:R_0201_0603Metric | R5 |
| 1 | 2n7 | Inductor_SMD:L_0402_1005Metric | L3 |
| 1 | 32KHz768 | 830009678:830009678 | X1 |
| 1 | 32MHz | Crystal:Crystal_SMD_TXC_7M-4Pin_3.2x2.5mm | X2 |
| 1 | Antenna_Chip | 830009678:2400MHz_PCB_Inverted_F | AE1 |
| 1 | B5819W | Diode_SMD:D_SOD-123 | D1 |
| 1 | BNO086 | Package_LGA:LGA-28_5.2x3.8mm_P0.5mm | U5 |
| 1 | Conn_ARM_SWD_TagConnect_TC2030 | Connector:Tag-Connect_TC2030-IDC-FP_2x03_P1.27mm_Vertical | J2 |
| 1 | DLF162500LT-5028A1 | HW_MoveCritic_Footprints:DLF162500LT-5028A1 | FLT1 |
| 1 | JST_PH_2.00mm | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J1 |
| 1 | LED | LED_SMD:LED_0402_1005Metric | D2 |
| 1 | MIC5365-3.3YD5 | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | STM32WB55CEU6 | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U1 |
| 1 | SW_Push | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | SW1 |
| 1 | USBLC6-2P6 | Package_TO_SOT_SMD:SOT-666 | U2 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J3 |
More from kapis20/IEEECompetition
1Similar boards
- 4 layers58 × 31 mm
- 4 layers67.4 × 35.4 mm
- 4 layers48 × 33 mm
Stm32-bt board
OdaiJ/stm32-bt-board
My attempt at following the Phil's Lab KiCad V7 tutorial on YouTube
60 parts1 - 4 layers80.5 × 32.5 mm
Stm32wb55-ble dev board
shivamtiwari020505/stm32wb55-ble-dev-board
Custom STM32WB55 development board integrating 2.4GHz BLE 5.x, LPUART, I2C, and UART via RS232/DB9 for PC and industrial machine interfacing. Designed to bridge modern wireless IoT with legacy wired systems.
63 parts1MIT - 4 layers
- 4 layers51 × 26 mm
- 4 layers50.8 × 26 mm
- 4 layers48 × 25 mm
Stm32mc
justinfederico/STM32testPCB
Custom STM32WB microcontroller to practice my PCB schematic and layout skills. Looking to get it printed soon! Bear in mind that this is an ameuter project, so there will probably be errors aplenty.
51 parts
Questions
How big is the HW MoveCritic KiCad Project PCB?
It measures 39.7 × 27.7 mm and has 4 copper layers, 1.58 mm thick.
What parts does the HW MoveCritic KiCad Project use?
55 parts, built around the STM32WB55CEU6, DLF162500LT-5028A1, BNO086 and MIC5365-3.3YD5-TR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the HW MoveCritic KiCad Project KiCad files?
From the kapis20/IEEECompetition repository on GitHub, at the commit this page was made from: the board is HW_MoveCritic/HW_MoveCritic_KiCad_Project/HW_MoveCritic_KiCad_Project.kicad_pcb and its schematic HW_MoveCritic/HW_MoveCritic_FBTM_KiCad_Project/HW_MoveCritic_FBTM_KiCad_Project.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the HW MoveCritic KiCad Project design in my own project?
Its repository states no licence, so its author keeps all rights: ask kapis20 before reusing the design.