2 layers60 × 38.6 mm
2 layers
Spinner
kangasp/crazy_hakz_spinner1Spinning LEDs
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 93
- Nets
- 152
- Pads
- 508
- Tracks, vias
- 256, 24
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 19 Nov 2022
- Updated
- 11 Nov 2025
Overview
Spinner is an open-source printed circuit board by kangasp, from the kangasp/crazy_hakz_spinner repository on GitHub. It is a 2-layer board with 93 parts on 152 nets, routed with 256 tracks and 24 vias.
It is built around the AP63205WU, SFH617A-3X006 and RS0102YH8. Its parts include 61 diodes, 5 ICs, 4 capacitors, 3 resistors and 1 connector. It belongs with the ESP8266 boards of this library.
Main components
3
AP63205WU
TSOT-23-6-40℃~+85℃@(TA) 1 1.1MHz 22uA 2A 3.8V~32V 5V Buck Built-in Fixed Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes TSOT-23-6 DC-DC Converters ROHSDiodes IncorporatedDC-DC Converters
SFH617A-3X006
DIP-4-55℃~+110℃ 1 1.35V 100% 200% 2us 2us 5.3kV 50mA 6V 70V Phototransistor DIP-4 Transistor, Photovoltaic Output Optoisolators ROHSVishay IntertechnologyTransistor, Photovoltaic Output Optoisolators
RS0102YH8
SOT-23-8-40℃~+85℃ 1 1.65V~5.5V 2 2.3V~5.5V 24Mbps Bidirectional Push-Pull、Open-drain SOT-23-8 Translators, Level Shifters ROHSJiangsu RUNIC TechTranslators, Level Shifters
README
README.mdcrazy_hakz_spinner
Spinning LEDs
Notes from 2-24-23
The footprint for the through beam sensor is wrong - pins 3 and 4 should be switched. Pin 4 is actually ground / emiter, and pin 3 is actually the collector / vcc.
The through beem should sensor should not be pulled up to VCC - which is 5v. It should be pulled up to 3.3v.
The level shifter should be moved - as it's too close to the mounting bracket... maybe get a bigger one.
Consider moving the positional / counter through beam to the edge.
Consider adding a testpoint header.
Parts
93| Qty | Value | Footprint | References |
|---|---|---|---|
| 61 | APA102 | Library:SK9822-hakz | D0, D101, D102, D103, D104, D105, D106, D107, D108, D109, D110, D111, D112, D113, D114, D115 +45 |
| 3 | Battery_Cell | Library:Spinner_BatteryHolder_Keystone_2460_1xAA | BT1, BT2, BT3 |
| 3 | ~3.3k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R3 |
| 2 | 22uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2 |
| 2 | IDC | Diode_SMD:D_SOD-123 | I1, I2 |
| 2 | SFH617A-3X006 | Library:MULTI_PART_THRU_BEAM | U3, U4 |
| 1 | .1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4 |
| 1 | 3v3 | TestPoint:TestPoint_Pad_D2.5mm | TP3 |
| 1 | 4.7uH | Inductor_SMD:L_0805_2012Metric_Pad1.05x1.20mm_HandSolder | L1 |
| 1 | AP63205WU | Package_TO_SOT_SMD:TSOT-23-6 | U1 |
| 1 | Adafruit_HUZZAH_ESP8266_breakout | Library:huzz_hakz | A1 |
| 1 | BATT | TestPoint:TestPoint_Pad_D2.5mm | TP9 |
| 1 | CI | TestPoint:TestPoint_Pad_D2.5mm | TP1 |
| 1 | DI | TestPoint:TestPoint_Pad_D2.5mm | TP5 |
| 1 | GND | TestPoint:TestPoint_Pad_D2.5mm | TP2 |
| 1 | LOGO | Library:hakz_04 | G*** |
| 1 | Micro_SD_Card | Connector_Card:microSD_HC_Hirose_DM3AT-SF-PEJM5 | J1 |
| 1 | Opto_0 | TestPoint:TestPoint_Pad_D2.5mm | TP8 |
| 1 | Opto_1 | TestPoint:TestPoint_Pad_D2.5mm | TP7 |
| 1 | Opto_2 | TestPoint:TestPoint_Pad_D2.5mm | TP6 |
| 1 | RS0102 | Package_SO:MSOP-8_3x3mm_P0.65mm | U2 |
| 1 | R_Network08 | Resistor_SMD:R_Array_Convex_5x1206 | RN1 |
| 1 | SFH617A-3X006 | Library:tcrt1000 | U5 |
| 1 | SW_SPDT | Button_Switch_SMD:SW_SPDT_CK-JS102011SAQN | SW1 |
| 1 | VCC | TestPoint:TestPoint_Pad_D2.5mm | TP4 |
More from kangasp/crazy_hakz_spinner
1Similar boards
- 4 layers173.2 × 52.5 mm
- 4 layers86 × 29 mm
- 2 layers40 × 23 mm
T12 SolderingStationScreen
Cube-Line/T12_SolderingStation
T12_SolderingStation base on ATMEL328P
27 parts1 - 2 layers28.3 × 14.3 mm
Tap Photosensor PCB
VoronDesign/Voron-Tap
Tap is a nozzle-based z-probe for the V2 and Trident printer designs. The entire toolhead moves to trigger an optical switch. Tap offers many advantages:
18 parts716GPL-3.0 - 6 layers84 × 98 mm
FujiNet-5200-Rev0
FujiNetWIFI/fujinet-hardware
Schematics and design files for FujiNet hardware
145 parts142 - 2 layers65 × 70 mm
Openradfan
andrekuehne/openradfan
An ESPHome-driven controller for radiator fans to improve heat output
49 parts29MIT - 4 layers96 × 172 mm
- 4 layers355 × 160 mm
LiBCM
doppelhub/Honda_Insight_LiBCM
Replacement BCM for G1 Honda Insight Lithium Conversion
717 parts25CC-BY-SA-4.0
Questions
What parts does the Spinner use?
93 parts, built around the AP63205WU, SFH617A-3X006 and RS0102YH8. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Spinner KiCad files?
From the kangasp/crazy_hakz_spinner repository on GitHub, at the commit this page was made from: the board is spinner.kicad_pcb and its schematic spinner.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Spinner design in my own project?
Its repository states no licence, so its author keeps all rights: ask kangasp before reusing the design.