
Pathogen Pedal prerouting
kaiduchane/ABASI-PATHOS-clone
DIY clone of the ABASI Pathos distortion pedal

DIY clone of the ABASI Pathos distortion pedal
Pathogen Pedal is an open-source printed circuit board by kaiduchane, from the kaiduchane/ABASI-PATHOS-clone repository on GitHub. It is a 4-layer board of 82 × 75 mm with 91 parts on 53 nets, routed with 343 tracks and 0 vias.
It is built around the NJM4580D. Its parts include 36 capacitors, 36 resistors, 5 diodes, 3 ICs and 1 switch. It belongs with the audio and music boards of this library.
The Abasi Pathos is a modern high-gain distortion pedal designed by guitarist Tosin Abasi and Horizon Devices. This project is an open-source clone that reverse-engineers the circuit for educational purposes and DIY builders. This pedal features a three-band active EQ, dual-stage clipping circuit, and tight low-end response designed for modern progressive metal tones. The design uses through-hole components where possible to make it accessible for beginners while maintaining the sonic characteristics of the original. Key Features:
Adjustable gain structure with asymmetrical clipping Active 3-band EQ (Bass/Mid/Treble) High input impedance JFET buffer True bypass switching Standard 9V center-negative power
| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 10K | _MB_resistors:0.5%22 | R4, R7, R13, R23, R102, R103, R104, R105, R106, R107, R108, R109, R110, R111, R112, R113 |
| 8 | 100u | _MB_caps-elec:0503 | C100, C101, C105, C106, C107, C108, C109, C110 |
| 6 | 1u | Capacitor_THT:C_Axial_L12.0mm_D6.5mm_P15.00mm_Horizontal | C6, C9, C11, C16, C19, C24 |
| 5 | 100n | _MB_caps-film:5mm_1n-300n | C14, C20, C102, C103, C104 |
| 5 | 1K | _MB_resistors:0.3%22.B | R2, R5, R9, R12, R16 |
| 5 | 1N4148 | _MB_diodes:DO41-2 | D1, D2, D3, D4, D5 |
| 4 | 470K | _MB_resistors:0.3%22.B | R3, R8, R15, R17 |
| 4 | 47n | Capacitor_THT:C_Axial_L17.0mm_D6.5mm_P20.00mm_Horizontal | C13, C15, C17, C22 |
| 3 | 220n | _MB_caps-film:5mm_1n-300n | C2, C3, C8 |
| 3 | 220p | _MB_caps-film:5mm_10p-180n | C1, C7, C10 |
| 3 | 47K | _MB_resistors:0.3%22.B | R10, R18, R19 |
| 3 | A100K | _MB_potentiometers:16MM_PADS.2 | Gain101, Mid101, Volume101 |
| 3 | NJM4580D | _MB_integrated_circuits:DIP08 | IC1, IC2, IC3 |
| 2 | 330p | _MB_caps-film:7.62mm | C21, C23 |
| 2 | 33K | _MB_resistors:0.4%22 | R20, R21 |
| 2 | 4n7 | _MB_caps-film:5mm_1n-300n | C12, C25 |
| 1 | 100K | _MB_resistors:0.2%22 | R11 |
| 1 | 10R | _MB_resistors:0.3%22.B | R101 |
| 1 | 1M | _MB_resistors:0.3%22.B | R1 |
| 1 | 1N5817 | _MB_diodes:DO35-3 | 1N5817 |
| 1 | 33n | _MB_caps-film:7.62mm | C4 |
| 1 | 470p | _MB_caps-film:5mm_10p-180n | C18 |
| 1 | 4K7 | _MB_resistors:0.3%22.B | R14 |
| 1 | 560p | _MB_caps-film:7.62mm | C5 |
| 1 | 680K | _MB_resistors:0.3%22.B | R22 |
| 1 | 6K8 | _MB_resistors:0.3%22.B | R6 |
| 1 | A50K | _MB_potentiometers:16MM_PADS.2 | Treble101 |
| 1 | B100k | _MB_potentiometers:16MM_PADS.2 | Bass101 |
| 1 | GND | _MB_supply_pins:PAD3 | GND1 |
| 1 | IN | _MB_supply_pins:PAD3 | SigIN1 |
| 1 | OUT | _MB_supply_pins:PAD3 | SigOUT1 |
| 1 | PWR | _MB_supply_pins:PAD3 | PWR+1 |
| 1 | SW_SPDT | _MB_switches:SPDT.WIRE | SW1 |

kaiduchane/ABASI-PATHOS-clone
DIY clone of the ABASI Pathos distortion pedal

creapunk/CLN-ClosedLoopNemaDriver
Compact closed-loop stepper motor driver designed for NEMA motors

pms67/HadesFCS
Complete flight control system designed from scratch. Hardware designed with KiCad.


dosdude1/2.5-inch-ide-ssd
A custom-designed IDE SSD for use in any machine that utilizies a 2.5" IDE hard disk.



joshajohnson/rf-sig-gen
MAX2871 based RF Signal Generator in an Adafruit Feather Form Factor

It measures 82 × 75 mm and has 4 copper layers, 1.6 mm thick.
91 parts, built around the NJM4580D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the kaiduchane/ABASI-PATHOS-clone repository on GitHub, at the commit this page was made from: the board is Pathogen_Pedal/Pathogen_Pedal.kicad_pcb and its schematic Pathogen_Pedal/Pathogen_Pedal.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask kaiduchane before reusing the design.