2 layers
TP Integrador
Amalia-O/TDCE
FIUBA - Electrónica - Taller de Diseño de Circuitos Electrónicos - Trabajo Integrador
39 parts
2 layers42 × 35 mm
Luminosite
johan-954/Projet_1DAProjet d'électronique de 1ere année
- Size
- 42 × 35 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 36
- Nets
- 41
- Pads
- 117
- Tracks, vias
- 217, 9
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 19 Apr 2026
- Updated
- 26 May 2026
Overview
Luminosite is an open-source printed circuit board by johan-954, from the johan-954/Projet_1DA repository on GitHub. It is a 2-layer board of 42 × 35 mm with 36 parts on 41 nets, routed with 217 tracks and 9 vias.
It is built around the MCP6022-I/P, AMS1117-5.0 and TL431D, with the BC547C and TQ2-L2-5V among its other parts. Its parts include 17 resistors, 6 capacitors, 5 ICs, 4 connectors and 2 transistors. It belongs with the ESP32 and RISC-V boards of this library.
Main components
5
MCP6022-I/P
PDIP-8-40℃~+125℃ 10MHz 1mA 1pA 1pA 2 2.5V~5.5V 3.5uV/℃ 30mA 500uV 7V/us 8.7nV/√Hz@10kHz 90dB Built-in compensation Rail-to-Rail Input, Rail-to-Rail Output PDIP-8 Operational Amplifier ROHSMicrochip TechnologyOperational Amplifier
AMS1117-5.0
SOT-223-40℃~+125℃ 1 1.3V 15V 1A 5V 60dB Fixed Positive Short Circuit Protection、Thermal shutdown SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
TL431D
SOT-23-40℃~+125℃ 100mA 2.495V~36V 2.495V~36V 40uA Adjustable Parallel ±0.4% SOT-23 Voltage Reference ROHSALJVoltage Reference
BC547C
TO-92-55℃~+150℃ 1 NPN 100mA 100nA 150MHz 300mV 45V 610 625mW 6V NPN TO-92 Bipolar (BJT) ROHSLGEBipolar (BJT)
TQ2-L2-5V
DIP,14x9mm-40℃~+70℃ 110V@DC、125V@AC 1A 2 Form C: 2C (DPDT-CO) 3ms 3ms 5V Dual Coil Silver + Gold Plated DIP,14x9mm Magnetic Latching Relays ROHSPanasonicMagnetic Latching Relays
Parts
36| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3, R4, R5, R6, R10, R11, R12, R15, R16, R17, R18, R19 |
| 3 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C5, C6 |
| 3 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Horizontal | J2, J3, J4 |
| 2 | 10p | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C4 |
| 2 | BC547C | BC547:TRANS_BC547C | Q3, Q4 |
| 2 | MCP6022 | MCP2022:SOP8P65_300X640X120L60X24N | U1, U3 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2 |
| 1 | 1N914 | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D1 |
| 1 | 2.2k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R13 |
| 1 | 220n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3 |
| 1 | 33k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7 |
| 1 | 5.1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R14 |
| 1 | 68k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
| 1 | AMS1117-5.0 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U5 |
| 1 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Horizontal | J1 |
| 1 | ESP32-C3_SUPERMINI_TH | ESP32-C3-Supermini:MODULE_ESP32-C3_SUPERMINI_TH | U4 |
| 1 | TL431D | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | TQ2-L2-5V | TQ2-L2-5V:TQ2 | K1 |
Similar boards
- 2 layers
- 2 layers60 × 69.1 mm
Nanovolt divider
kuvychko/nanovolt-divider
Programmable 1e-5/1e-6/1e-7 precision attenuator for nanovolt metrology: KiCad, ESP32 firmware, calibration method and results
68 parts - 2 layers20.3 × 110 mm
4HPico
rheslip/2HPico-Eurorack-Module-Hardware
2HP Eurorack module based on Raspberry Pi Pico 2
73 parts84 - 2 layers73.9 × 46 mm
- 2 layers147 × 76 mm
- 2 layers100 × 74 mm
Qym solder
basson/qym-solder
QymSolder - Soldering station three in one - hakko t12, hot air gun, d909/898D or analog.
135 parts4GPL-3.0 - 2 layers73 × 66 mm
Przetwora v2
ThertyOne/bird-feeder
Z wyjścia baterii energia trafia do przetwornicy boost 5 V, zbudowanej od podstaw na bazie generatora PWM LMC555 i MOSFETa IRLML6344, która zasila ESP32 i peryferia – serwo sterujące karmnikiem, LEDy oświetleniowe oraz…
34 parts1
Questions
How big is the Luminosite PCB?
It measures 42 × 35 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Luminosite use?
36 parts, built around the MCP6022-I/P, AMS1117-5.0, TL431D and BC547C. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Luminosite KiCad files?
From the johan-954/Projet_1DA repository on GitHub, at the commit this page was made from: the board is KiCad/Luminosite/Luminosite.kicad_pcb and its schematic KiCad/Luminosite/Capteur_luminosite.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Luminosite design in my own project?
Its repository states no licence, so its author keeps all rights: ask johan-954 before reusing the design.