Skip to the content
2 layersWiFiLamp, the printed circuit board in 3D

A Lamp controlled over WiFi using an ESP8266-01

Copper layers
2
Thickness
1.6 mm
Parts
14
Nets
21
Pads
49
Tracks, vias
54, 0
Routed
Yes
KiCad
KiCad 4
Created
8 Jan 2017
Updated
19 Feb 2017

Overview

WiFiLamp is an open-source printed circuit board by belimawr, from the belimawr/WiFiLamp repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board with 14 parts on 21 nets, routed with 54 tracks and 0 vias.

It is built around the TQ2-L2-5V. Its parts include 5 resistors, 3 connectors, 2 diodes, 2 transistors and 1 IC. It belongs with the radio and wireless and lEDs and displays boards and the ESP8266 boards of this library.

Main components

1

README

README.md

WiFi Lamp

This is a simple project that uses a ESP8266-01 and a 2-coil latching relay to control a lamp (or any other load) over WiFi using a simple web page.

TODO

  • Add the schematic
  • Create a nice PCB
  • Improve the web page

Licence

GPLV3

Parts

14
QtyValueFootprintReferences
34K7Resistors_ThroughHole:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR2, R3, R4
21N4007Diodes_ThroughHole:D_DO-41_SOD81_P10.16mm_HorizontalD1, D2
22N2222TO_SOT_Packages_THT:TO-92_Inline_Narrow_OvalQ1, Q2
2470RResistors_ThroughHole:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1, R5
1CN1Pin_Headers:Pin_Header_Straight_1x03_Pitch2.54mmP2
1CN2Pin_Headers:Pin_Header_Straight_1x03_Pitch2.54mmP1
1CONN_01X05Pin_Headers:Pin_Header_Straight_1x05_Pitch2.54mmP3
1ESP-01v090ESP8266:ESP-01U1
1TQ2-L2-5VBelimawr:ATQ229H1

Similar boards

  • 2 layers42 × 35 mmLuminosite, the printed circuit board in 3D

    Luminosite

    johan-954/Projet_1DA

    Projet d'électronique de 1ere année

    36 parts
  • 2 layers60 × 69.1 mmNanovolt divider, the printed circuit board in 3D

    Nanovolt divider

    kuvychko/nanovolt-divider

    Programmable 1e-5/1e-6/1e-7 precision attenuator for nanovolt metrology: KiCad, ESP32 firmware, calibration method and results

    68 parts
  • 2 layers116.8 × 30 mmType d, the printed circuit board in 3D

    Type d

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    14 parts3kApache-2.0
  • 2 layers32 × 22 mmDiff driver, the printed circuit board in 3D

    Diff driver

    rene-dev/stmbl

    AC Servo Driver for STM32F4

    14 parts990GPL-3.0
  • 2 layers34 × 45 mm2032Charger, the printed circuit board in 3D

    2032Charger

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    14 parts915
  • 2 layers34 × 109.9 mmTdisplay s3, the printed circuit board in 3D

    Tdisplay s3

    landonr/homeThing

    Wifi Smart Home Remotes that run on ESPHome

    14 parts551GPL-3.0
  • 2 layers45.3 × 42.7 mmMainPcb, the printed circuit board in 3D

    MainPcb

    adamb314/ServoProject

    Getting the most out of your hobby servo

    14 parts545
  • 2 layers42.5 × 28.8 mmC5VRX JACK DIY, the printed circuit board in 3D

    C5VRX JACK DIY

    Twotoz/C5VRX

    Ultra-minimal, zero-CPU 5.8 GHz analog FPV video receiver using ESP32-C5 Wi-Fi 6 PHY MODEM_DIAG, BitScrambler WBFM demodulation & resistor DAC CVBS

    14 parts515GPL-3.0

Questions

What parts does the WiFiLamp use?

14 parts, built around the TQ2-L2-5V. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the WiFiLamp KiCad files?

From the belimawr/WiFiLamp repository on GitHub, at the commit this page was made from: the board is Schematic/WiFiLamp.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the WiFiLamp design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).