
SimpleCANBreakout
jlpoltrack/CAN-Breakouts
CAN and CAN FD breakout boards: SimpleCANBreakout, SimpleCANBreakoutMicro, MCP251863Breakout (KiCad 10)

CAN and CAN FD breakout boards: SimpleCANBreakout, SimpleCANBreakoutMicro, MCP251863Breakout (KiCad 10)
MCP251863Breakout is an open-source printed circuit board by jlpoltrack, from the jlpoltrack/CAN-Breakouts repository on GitHub, published under the MIT licence. It is a 2-layer board of 32 × 32 mm with 30 parts on 24 nets, routed with 124 tracks and 54 vias.
It is built around the AMS1117-3.3. Its parts include 11 capacitors, 2 ICs, 1 resistor and 1 crystal. It belongs with the interfaces and adapters boards of this library.
A tiny CAN transceiver breakout. It converts a microcontroller's logic-level CAN TX/RX to a CAN bus on a JST-GH connector, with an onboard 3.3 V regulator and optional 120 Ω termination.

Designed in KiCad 10. See SimpleCANBreakout for a larger version with solder pads and an AMS1117 regulator.
J1 — MCU side (1×4 pin header, 2.54 mm)
| Pin | Signal |
|---|---|
| 1 | CAN RX |
| 2 | CAN TX |
| 3 | +5V |
| 4 | GND |
J2 — CAN bus (JST-GH 4-pin, SM04B-GHS-TB)
| Pin | Signal |
|---|---|
| 1 | +5V |
| 2 | CANH |
| 3 | CANL |
| 4 | GND |
The +5V pins on J1 and J2 are connected, so the board can be powered from either side. CAN TX/RX are 3.3 V logic.
Bridge JP1 (bottom side) to connect the 120 Ω resistor across CANH/CANL. Do this only if the board sits at an end of the bus.
| Ref | Value | Package | LCSC |
|---|---|---|---|
| U3 | SN65HVD230 | SOIC-8 | C12084 |
| U2 | XC6206 3.3 V | SOT-23-3 | C5446 |
| C1, C4, C5 | 1 µF | 0603 | |
| C2, C3, C6 | 100 nF | 0603 | |
| R1 | 120 Ω | 0603 | |
| J1 | 1×4 header | 2.54 mm | |
| J2 | JST-GH 4-pin | SM04B-GHS-TB | C189895 |
SimpleCANBreakoutMicro.kicad_sch / .kicad_pcb / .kicad_pro — KiCad projectSimpleCANBreakoutMicro.pdf — schematicproduction/ — fabrication outputs generated with the Fabrication Toolkit plugin: Gerbers and drill files (SimpleCANBreakoutMicro.zip), BOM, and pick-and-place positions, ready for JLCPCB| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | TestPoint_Square | TestPoint:TestPoint_Pad_2.0x2.0mm | CANH, CANL, CLKO, CS, GND, GND2, INT, INT0, INT1, MISO, MOSI, PWR, PWR2, SCK, STBY |
| 5 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C3, C5, C6, C7 |
| 4 | 10u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C4, C10, C12 |
| 2 | 10p | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C8, C9 |
| 1 | 120 | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | R1 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_2016-4Pin_2.0x1.6mm | Y1 |
| 1 | MCP251863T-H-SS | Package_SO:SSOP-28_5.3x10.2mm_P0.65mm | U1 |

jlpoltrack/CAN-Breakouts
CAN and CAN FD breakout boards: SimpleCANBreakout, SimpleCANBreakoutMicro, MCP251863Breakout (KiCad 10)

jlpoltrack/CAN-Breakouts
CAN and CAN FD breakout boards: SimpleCANBreakout, SimpleCANBreakoutMicro, MCP251863Breakout (KiCad 10)


pascallanger/DIY-Multiprotocol-TX-Module
Multiprotocol TX Module (or MULTI-Module) is a 2.4GHz transmitter module which controls many different receivers and models.

fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io


MaltWhiskey/Mega-Cube
16x16x16 PL9823 Cube with Teensy 4.0 and FlexIO driver



shamansystems/Cheap-FOCer-2
Low-Cost Motor Controller based on the VESC 6
It measures 32 × 32 mm and has 2 copper layers, 1.6 mm thick.
30 parts, built around the AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the jlpoltrack/CAN-Breakouts repository on GitHub, at the commit this page was made from: the board is MCP251863Breakout/MCP251863Breakout.kicad_pcb and its schematic MCP251863Breakout/MCP251863Breakout.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).