4 layers30 × 37.2 mm
Pd buddy sink
psten/pd-buddy-sink
This is the circuit board for the PD Buddy Sink, a device which aims to make USB Power Delivery accessible to any electronics hobbyist.
43 parts1
4 layers76.2 × 15.2 mm
Usb c
jessfraz/usbc-pal10This is a slighly modified version of pd-buddy.
- Size
- 76.2 × 15.2 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 34
- Nets
- 21
- Pads
- 200
- Tracks, vias
- 464, 77
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 2 Oct 2020
- Updated
- 5 Oct 2020
Overview
Usb c is an open-source printed circuit board by jessfraz, from the jessfraz/usbc-pal repository on GitHub. It is a 4-layer board of 76.2 × 15.2 mm with 34 parts on 21 nets, routed with 464 tracks and 77 vias.
It is built around the FUSB302B11MPX, B140-E3 and DMP3017SFG, with the MM3Z5V6T1GX and MMBT3904 among its other parts. Its parts include 11 capacitors, 9 resistors, 4 diodes, 3 ICs and 3 connectors. It belongs with the STM32 boards of this library.
Main components
5
FUSB302B11MPX
MLP-14-40℃~+85℃ 25uA 3.3V、5V 560mA Controller USB 3.1 MLP-14 USB Converters ROHSonsemiUSB Converters
B140-E3
SMA(DO-214AC)-65℃~+150℃ 1 Independent 1A 200uA@40V 30A 40V 520mV@1A SMA(DO-214AC) Schottky Diodes ROHSVishay IntertechnologySchottky Diodes
DMP3017SFG
PowerDI3333-8-55℃~+150℃ 1 P-Channel 10mΩ@10V 11.5A 2.246nF 294pF 30V 352pF 3V 41nC@10V 940mW P-Channel ±25V PowerDI3333-8 MOSFETs ROHSDiodes IncorporatedMOSFETs
MM3Z5V6T1GX
SOD-323Zener DiodesNexperia
MMBT3904
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mA 200mW 300MHz 300mV 40V 6V NPN SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)
README
README.mdParts
34| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 0.1μF | Capacitor_SMD:C_0402_1005Metric | C1, C2, C3, C4, C5, C6, C11 |
| 4 | 2kΩ | Resistor_SMD:R_0402_1005Metric | R2, R3, R4, R8 |
| 3 | 10kΩ | Resistor_SMD:R_0402_1005Metric | R1, R5, R7 |
| 2 | 1μF | Capacitor_SMD:C_0402_1005Metric | C7, C8 |
| 1 | 100kΩ | Resistor_SMD:R_0402_1005Metric | R9 |
| 1 | 1μF | Capacitor_SMD:C_0603_1608Metric | C9 |
| 1 | 2.2μF | Capacitor_SMD:C_0603_1608Metric | C10 |
| 1 | 220kΩ | Resistor_SMD:R_0402_1005Metric | R6 |
| 1 | AP2204R-3.3 | Package_TO_SOT_SMD:SOT-89-3 | U2 |
| 1 | B140-E3 | Diode_SMD:D_SMA | D4 |
| 1 | DMP3017SFG | housings_son:Diodes_PowerDI3333-8 | Q2 |
| 1 | FUSB302B11MPX | Package_DFN_QFN:WQFN-14-1EP_2.5x2.5mm_P0.5mm_EP1.45x1.45mm | U1 |
| 1 | JUMPER | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1 |
| 1 | MM325V6T1G | Diode_SMD:D_SOD-323 | D1 |
| 1 | MM3Z5V6T1G | Diode_SMD:D_SOD-323 | D2 |
| 1 | MMBT3904 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | OUTPUT | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MPT-0,5-2-2.54_1x02_P2.54mm_Horizontal | J3 |
| 1 | STATUS_LED | LED_SMD:LED_0603_1608Metric | D3 |
| 1 | STM32F072C8Ux | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U3 |
| 1 | SWD | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMD | J2 |
| 1 | SWITCH | Button_Switch_SMD:SW_SPST_PTS810 | SW1 |
| 1 | USB_C | Connector_USB:USB_C_Receptacle_Amphenol_12401610E4-2A | J1 |
Similar boards
- 4 layers42.4 × 21 mm
Usb c otter
lucysrausch/usb-c-otter
USB PD trigger with XT60 out and WS2812 / APA102 LED pads.
45 parts6 - 2 layers28 × 30 mm
- 6 layers200 × 75 mm
- 4 layers61.4 × 42.6 mm
ESP Smart IoT Power Bank
LUntiedt/Smart_IOT_PowerBank_PCB
A bidirectional USB-C Power Delivery (PD) power bank built around a software-defined PD stack and an I²C buck-boost charger. This repository holds the KiCad hardware design (schematic, layout, BOM, fabrication outputs).
98 parts1 - 4 layers203.1 × 155.8 mm
Nixie 2025 v3
moro696/nixie-clock
here i will post documentation for the nixie clock project.
147 parts1GPL-3.0 - 4 layers85 × 48.6 mm
GPS Compass
bismarx-v1/GPS-Compass
The compass that doesnt point to north, but it points to a GPS location, or a list of locations and points to the nearest one
120 parts1 - 4 layers38 × 60 mm
Questions
How big is the Usb c PCB?
It measures 76.2 × 15.2 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Usb c use?
34 parts, built around the FUSB302B11MPX, B140-E3, DMP3017SFG and MM3Z5V6T1GX. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Usb c KiCad files?
From the jessfraz/usbc-pal repository on GitHub, at the commit this page was made from: the board is usb-c/usb-c.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Usb c design in my own project?
Its repository states no licence, so its author keeps all rights: ask jessfraz before reusing the design.