
Pico w rover
NikodemBartnik/Mini-Mars-Rover
Educational robotic platform made to look like a mini mars rover

Breakout board for nRF24L01+ 2.4GHz radio module.
NRF24L01-breakout is an open-source printed circuit board by jedp, from the jedp/nRF24L01-breakout repository on GitHub, published under the MIT licence. It is a 2-layer board of 28.6 × 16.4 mm with 17 parts on 20 nets, routed with 119 tracks and 16 vias.
It is built around the NRF24L01. Its parts include 7 capacitors, 3 resistors, 3 ICs, 2 connectors and 1 crystal. It belongs with the interfaces and adapters boards of this library.
The Nordic Semiconductor nRF24L01.
Antenna constructed according to AN043.

| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 22pF | Capacitor_SMD:C_0402_1005Metric | C1, C2 |
| 2 | Conn_01x04_Female | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1, J2 |
| 1 | 0k | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 10nF | Capacitor_SMD:C_0402_1005Metric | C9 |
| 1 | 1M | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 1nF | Capacitor_SMD:C_0402_1005Metric | C8 |
| 1 | 2.2nF | Capacitor_SMD:C_0402_1005Metric | C3 |
| 1 | 22k | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | 33nF | Capacitor_SMD:C_0402_1005Metric | C7 |
| 1 | 4.7µF | Capacitor_SMD:C_0603_1608Metric | C10 |
| 1 | Antenna_PCB_2.4GHz_50Ohm | RF_Antenna:Antenna_PCB_2.4GHz_50Ohm | U2 |
| 1 | Balun_2450BM14A0002 | RF_Converter:Balun_Johanson_1.6x0.8mm | U3 |
| 1 | Crystal_GND24_Small | Crystal:Crystal_SMD_2520-4Pin_2.5x2.0mm | Y1 |
| 1 | LOGO | LOGO | G*** |
| 1 | NRF24L01 | Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm | U1 |

NikodemBartnik/Mini-Mars-Rover
Educational robotic platform made to look like a mini mars rover

DAlexis/caustic-lasertag-system
Caustic project is a full-featured indoor and outdoor lasertag system

CGrassin/biosignals
Board for the acquisition of bio-potentials (EMG, ECG, EEG, etc.).

microdynamics-robot-quadcopter/breeze_electronics_design
This project is created and managed by EDA softwares, which contains the breeze quadcopter's component library, footprint library, schematic, printed circuit boards, etc.




It measures 28.6 × 16.4 mm and has 2 copper layers, 1.6 mm thick.
17 parts, built around the NRF24L01. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the jedp/nRF24L01-breakout repository on GitHub, at the commit this page was made from: the board is nRF24L01-breakout/nRF24L01-breakout.kicad_pcb and its schematic nRF24L01-breakout/nRF24L01-breakout.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).