
Battery pico
4f48/battery-pico
A battery charger add-on board for all Raspberry Pi Pico development boards.

Terra 2.0 Firmware and Hardware
Terra HW is an open-source printed circuit board by jamesmendel, from the jamesmendel/terra-nova repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 76.9 × 67.3 mm with 95 parts on 92 nets, routed with 792 tracks and 208 vias.
It is built around the ESP32-S3-MINI-1-N4R2, DRV2605LDGS and AP2112K-3.3TRG1, with the BNO055, BQ21040DBV and SN74LVC1G14DRL among its other parts. Its parts include 26 resistors, 18 capacitors, 12 diodes, 7 ICs and 5 connectors. It belongs with the ESP32 boards of this library.
⚠️ NOTICE: This project is currently in an experimental phase and is undergoing rapid developments ⚠️
The TERRA App generates coordinates or checkpoints from a starting point and an ideal trail length using the ChatGPT API.
Node.js v21.5body-parser v1.20.2cors v2.8.5express v4.19.0node-fetch v3.3.2To run the TERRA App locally, follow these steps:
YOUR_OPENAI_API_KEY with it in the server.js file.YOUR_MAPS_KEY with it in the index.js file.node server.jsindex.html in a browser to use the app for generating a route.config.h file which contains the generated route configuration.config.h file in the Arduino code directory with the newly downloaded file.The hardware for the TERRA project is based on an ESP32 device, equipped with a range of sensors for navigation and interaction.
The main components required are:
Connect the components together in the following order:
| ESP32 Pin | Screen | Motor Driver | Compass | GPS | Push Button |
|---|---|---|---|---|---|
| 3V | VCC | VIN | VIN | VIN | |
| GND | GND | GND | GND | GND | GND |
| 19 (MOSI) | DIN | ||||
| 4 (A5) | RST | ||||
| 5 (SCK) | CLK | ||||
| 12 | BL | ||||
| 15 | CS | ||||
| 32 (A7) | OFF | ||||
| 33 | DC | ||||
| SDA | SDA | SDA | |||
| SCL | SCL | SCL | |||
| RX | TX | ||||
| TX | RX |
To run the Arduino code, you will need to set up the ESP32 board and install the necessary libraries.
ESP32 Arduino Setup: Add the ESP32 board to the Arduino IDE.
https://raw.githubusercontent.com/espressif/arduino-esp32/gh-pages/package_esp32_dev_index.jsonInstall Libraries: Install the following libraries through the Library Manager in the Arduino IDE.
TinyGPSPlus.hTFT_eSPI.hAdafruit_DRV2605.hUpload the Code: After installing the libraries and updating the config.h file with new coordinates, upload the code to the ESP32 device. The device should work without further adjustments.
Debug Mode: A debugMode flag is available in the code. To test the device with manual coordinates, set this flag to true and input coordinates into the serial monitor.
You can use your own checkpoint files by converting black and white images into a compatible format.
.bmp images to .XBM format using this online tool.images/checkpoints directory with your customized .h file.Vision + Concept: Modem
Industrial Design: Panter&Tourron
Software + Hardware: Alice Stewart
Product Renderings: Côme Lart
Illustrations: Hugo Bernier
Campaign Teaser: Michael Willis
TERRA is licensed under the GNU General Public License v3.0 © 2024 Modem
| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100k | Resistor_SMD:R_0603_1608Metric | R7, R8, R9, R10, R11, R13, R14, R23, R24, R27 |
| 9 | 0.1u | Capacitor_SMD:C_0603_1608Metric | C2, C7, C8, C13, C14, C17, C18, C19, C21 |
| 8 | 1u | Capacitor_SMD:C_0603_1608Metric | C3, C4, C5, C6, C9, C10, C11, C12 |
| 6 | 10k | Resistor_SMD:R_0603_1608Metric | R4, R12, R17, R19, R20, R21 |
| 5 | 1.5k | Resistor_SMD:R_0603_1608Metric | R5, R6, R18, R26, R31 |
| 4 | 5.1k | Resistor_SMD:R_0603_1608Metric | R2, R3, R15, R16 |
| 4 | B5819WS-TP | Diode_SMD:D_SOD-323 | D3, D4, D11, D12 |
| 4 | DESD5V0U1BB-7 | Diode_SMD:D_SOD-523 | D6, D7, D8, D9 |
| 3 | Fiducial | Fiducial:Fiducial_1mm_Mask2mm | FID1, FID2, FID3 |
| 3 | KMR231NG | Button_Switch_SMD:SW_Push_1P1T_NO_CK_KMR2 | SW2, SW3, SW4 |
| 2 | GND | M20048-1:TestPoint_Pad_D1.5mm_WITH_LABEL | TP5, TP6 |
| 2 | Hole M2 | MountingHole:MountingHole_2.2mm_M2 | H1, H2 |
| 2 | Plated Hole M2 | MountingHole:MountingHole_2.2mm_M2_Pad | H3, H4 |
| 1 | +3.3V | Diode_SMD:D_0603_1608Metric | D5 |
| 1 | 0532610271 | Connector_Molex:Molex_PicoBlade_53261-0271_1x02-1MP_P1.25mm_Horizontal | J3 |
| 1 | 0R | Resistor_SMD:R_0603_1608Metric | R25 |
| 1 | 22u | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 2N7002 | Package_TO_SOT_SMD:SOT-23 | Q2 |
| 1 | 3.3V | M20048-1:TestPoint_Pad_D1.5mm_WITH_LABEL | TP3 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | B8B-PH-SM4-TB | Connector_JST:JST_PH_B8B-PH-SM4-TB_1x08-1MP_P2.00mm_Vertical | J5 |
| 1 | BNO055 | Package_LGA:LGA-28_5.2x3.8mm_P0.5mm | U5 |
| 1 | BQ21040DBV | Package_TO_SOT_SMD:SOT-23-6 | U3 |
| 1 | CHARGING | Diode_SMD:D_0603_1608Metric | D1 |
| 1 | Conn_Coaxial | Connector_Coaxial:U.FL_Molex_MCRF_73412-0110_Vertical | J4 |
| 1 | DMP3099L | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | DRV2605LDGS | Package_SO:VSSOP-10_3x3mm_P0.5mm | U4 |
| 1 | ESP32-S3-MINI-1 | RF_Module:ESP32-S2-MINI-1 | U1 |
| 1 | GPIO48 | Diode_SMD:D_0603_1608Metric | D10 |
| 1 | GT-USB-7010ASV | Connector_USB:USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J1 |
| 1 | I2C_SCL | M20048-1:TestPoint_Pad_D1.5mm_WITH_LABEL | TP8 |
| 1 | I2C_SDA | M20048-1:TestPoint_Pad_D1.5mm_WITH_LABEL | TP7 |
| 1 | KSS3xxGx | C&K:SW_KSS323_CNK | SW5 |
| 1 | PA1616D | TESO-LIV3F:PA1616D | U10 |
| 1 | PMEG2010AEH | Diode_SMD:D_SOD-123 | D2 |
| 1 | RXD0 | M20048-1:TestPoint_Pad_D1.5mm_WITH_LABEL | TP2 |
| 1 | RXD1 | M20048-1:TestPoint_Pad_D1.5mm_WITH_LABEL | TP12 |
| 1 | S2B-PH-SM4-TB | Connector_JST:JST_PH_S2B-PH-SM4-TB_1x02-1MP_P2.00mm_Horizontal | J2 |
| 1 | SN74LVC1G14DRL | Package_TO_SOT_SMD:SOT-553 | U9 |
| 1 | SPI_CS0 | M20048-1:TestPoint_Pad_D1.5mm_WITH_LABEL | TP9 |
| 1 | SPI_MOSI | M20048-1:TestPoint_Pad_D1.5mm_WITH_LABEL | TP10 |
| 1 | SPI_SCK | M20048-1:TestPoint_Pad_D1.5mm_WITH_LABEL | TP11 |
| 1 | TXD0 | M20048-1:TestPoint_Pad_D1.5mm_WITH_LABEL | TP1 |
| 1 | TXD1 | M20048-1:TestPoint_Pad_D1.5mm_WITH_LABEL | TP14 |
| 1 | VUSB | M20048-1:TestPoint_Pad_D1.5mm_WITH_LABEL | TP13 |
| 1 | V_SW | M20048-1:TestPoint_Pad_D1.5mm_WITH_LABEL | TP4 |

4f48/battery-pico
A battery charger add-on board for all Raspberry Pi Pico development boards.

Robast-GmbH/PCB_Designs
This repository contains all the necessary files and instructions for the PCBs that are designed using KiCad. Here is an overview of the main components: - .github: Contains Github-specific configurations, including…




Talw3g/linear_act_controller
Controller for 24V linear actuator with potentiometer position control and feedback.

Thinkpad4by3/chibitron
Electrostatic CRT driver designed from the ground up for performance, versatility and ease-of-manufacturability

proegssilb/lightsaber-hardware
PCBs and other files for lightsaber soundboard hardware.
It measures 76.9 × 67.3 mm and has 4 copper layers, 1.55 mm thick.
95 parts, built around the ESP32-S3-MINI-1-N4R2, DRV2605LDGS, AP2112K-3.3TRG1 and BNO055. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the jamesmendel/terra-nova repository on GitHub, at the commit this page was made from: the board is Hardware/Terra-HW.kicad_pcb and its schematic Hardware/Microcontroller.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).