

Keyboard
This is the second iteration of my custom mechanical keyboard, a low-profile board aiming to be reliable, portable and fully-featured.
- Size
- 331 × 102 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 151
- Nets
- 109
- Pads
- 580
- Tracks, vias
- 831, 110
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 24 Sep 2024
- Updated
- 3 Jan 2025
Overview
Keyboard is an open-source printed circuit board by jackbrad1ey, from the jackbrad1ey/thingamaboard_v2 repository on GitHub, published under the MIT licence. It is a 2-layer board of 331 × 102 mm with 151 parts on 109 nets, routed with 831 tracks and 110 vias.
It is built around the RP2040, W25Q128JVSIQ and USBLC6-2SC6, with the NCD0805R1 and S8550 among its other parts. Its parts include 51 diodes, 50 switches, 16 capacitors, 13 resistors and 4 ICs. It belongs with the keyboards and input boards and the RP2040 boards of this library.
Main components
5RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)NCD0805R1
LED0805-30℃~+85℃ 1.6V~2.6V 130° 195mcd 25mA 615nm~630nm 630nm 65mW Discrete Diode Red 0805 LED Indication - Discrete ROHSFoshan NationStar OptoelectronicsLED Indication - DiscreteS8550
SOT-23-55℃~+150℃ 1 PNP 100nA 120 150MHz 25V 300mW 500mA 5V 600mV PNP SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)
README
README.mdThingamaboard V2
This is the second iteration of my custom mechanical keyboard, a low-profile board aiming to be reliable, portable and fully-featured.


Parts
151| Qty | Value | Footprint | References |
|---|---|---|---|
| 50 | D_Small | Diode_SMD:D_SOD-123 | D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23, D24 +34 |
| 50 | SW_Push | local-library:SW_PG1350 | SW1, SW2, SW10, SW11, SW12, SW13, SW14, SW15, SW16, SW17, SW18, SW19, SW20, SW21, SW22, SW23 +34 |
| 10 | 100n | Capacitor_SMD:C_0402_1005Metric | C2, C5, C6, C7, C10, C11, C12, C13, C14, C15 |
| 9 | , , , , , , , , | ||
| 6 | 10k | Resistor_SMD:R_0402_1005Metric | R4, R5, R6, R7, R8, R10 |
| 5 | 27 | Resistor_SMD:R_0402_1005Metric | R1, R2, R3, R12, R13 |
| 3 | TestPoint | TestPoint:TestPoint_Pad_D2.0mm | TP1, TP2, TP3 |
| 2 | 10u | Capacitor_SMD:C_1206_3216Metric | C1, C16 |
| 2 | 15p | Capacitor_SMD:C_0402_1005Metric | C3, C4 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R9, R11 |
| 2 | 1u | Capacitor_SMD:C_0402_1005Metric | C8, C9 |
| 1 | local-library:monkei_but_smaller | ||
| 1 | ABM8-272_T3 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | LOGO | local-library:rust_crab | |
| 1 | NCD0805 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 1 | NCP1117-3.3_SOT223 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U4 |
| 1 | S8550 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | USB_C_Receptacle_USB2.0 | local-library:TYPE-C-31-M-12 | J1 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U3 |
Similar boards
- 2 layers163.7 × 124.3 mm

- 2 layers99.1 × 99 mm

XDuinoRail Debug
chatelao/xDuinoRail-Decoder
The friendly decoder development plattform for model railroad tinkers.
170 partsAGPL-3.0 - 2 layers

Controller
dario0603/Hotplate
Hotplate is a DIY electronics project focused on the design and development of a hotplate and its associated control electronics.
101 parts - 4 layers30.5 × 30.5 mm

Merlyn435
YeetTheAnson/Merlyn435-Flight-Stack
Successor to the Merlyn411 25mm flight controller. The flight stack includes a 3in1 20mm flight controller and a 20mm ESC.
106 parts6 - 4 layers70 × 157.5 mm

Controller Tv Lift
vyrubaev/TV-Lift-Controller
TVLift Controller is an intelligent controller for TV lift and lower mechanisms, based on the ESP32 microcontroller.
103 parts - 2 layers42 × 67 mm

- 2 layers307.7 × 89.2 mm

- 2 layers352.5 × 120 mm

PyKey87
jpconstantineau/PyKey60
The PyKey60 is a custom programmable mechanical keyboard with a standard ANSI 60% keyboard layout compatible with any cases made for the GH60. The PyKey60 uses mechanical switches (Cherry MX type).
310 parts57
Questions
How big is the Keyboard PCB?
It measures 331 × 102 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Keyboard use?
151 parts, built around the RP2040, W25Q128JVSIQ, USBLC6-2SC6 and NCD0805R1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Keyboard KiCad files?
From the jackbrad1ey/thingamaboard_v2 repository on GitHub, at the commit this page was made from: the board is pcb/keyboard.kicad_pcb and its schematic pcb/MCU.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Keyboard design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).