2 layers99.1 × 92.7 mm
Controller
dario0603/Hotplate
Hotplate is a DIY electronics project focused on the design and development of a hotplate and its associated control electronics.
100 parts
2 layers
Controller
dario0603/HotplateHotplate is a DIY electronics project focused on the design and development of a hotplate and its associated control electronics.
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 101
- Nets
- 89
- Pads
- 417
- Tracks, vias
- 758, 61
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 20 Mar 2026
- Updated
- 20 Oct 2026
Overview
Controller is an open-source printed circuit board by dario0603, from the dario0603/Hotplate repository on GitHub. It is a 2-layer board with 101 parts on 89 nets, routed with 758 tracks and 61 vias.
It is built around the RP2040, W25Q128JVSIQ and AMS1117-5.0, with the AP2112K-3.3, AO3400A and BZD27C10P among its other parts. Its parts include 30 resistors, 25 capacitors, 10 diodes, 7 connectors and 5 ICs. It belongs with the RP2040 boards of this library.
Main components
10
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
AMS1117-5.0
SOT-223-40℃~+125℃ 1 1.3V 15V 1A 5V 60dB Fixed Positive Short Circuit Protection、Thermal shutdown SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
AP2112K-3.3
SOT253.3V 600mA CMOS Low Dropout Linear Regulator with EnableDiodes IncorporatedUncategorised
AO3400A
SOT-23-55℃~+150℃ 1 N-channel 1.45V 1.4W 30V 48mΩ@2.5V 5.7A 50pF 630pF 75pF 7nC@10V N-Channel SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETsBZD27C10P
Sub-SMAZener DiodesTaiwan Semiconductor
EC11B15242AE
插件-40℃~+85℃ 10mA 30/15 5V Incremental Right-Angle Two-phase output Plugin Rotary Encoders ROHSALPSALPINERotary Encoders
IRF540N
TO-2201 N-channel 1.35nF 100V 130W 280pF 33A 35mΩ@10V 4V 52nC@10V 85pF N-Channel TO-220 MOSFETs ROHSOSENMOSFETsS8050
SOT-23-55℃~+150℃ 1 NPN 100MHz 100nA 120 25V 300mW 500mA 5V 600mV NPN SOT-23 Bipolar (BJT) ROHShongjiachengBipolar (BJT)S8550
SOT-23-55℃~+150℃ 1 PNP 100nA 120 150MHz 25V 300mW 500mA 5V 600mV PNP SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)
README
README.mdHotplate
An open-source hotplate project for electronics and PCB work.
Work in Progress — This project is currently under development. Hardware designs, PCB revisions, documentation, and other project files may change.
Overview
Hotplate is a DIY electronics project focused on the design and development of a hotplate and its associated control electronics.
This repository is intended to collect the hardware designs, PCB documentation, and project resources as development progresses.
PCB Designs
Hotplate Resistor
The custom PCB designed for the hotplate heating element.
Hotplate Control Board v1.1
The control electronics PCB, revision v1.1.
Repository Structure
Hotplate/
├── img/
│ ├── hotplate-control-board-v1.1.png
│ └── hotplate-resistor.png
├── Kicad/
│ ├── Control board/
│ │ ├── Control board v1.0/
│ │ ├── Control board v1.1/
│ │ └── Control board v1.2/
│ ├── Resistor 10x10/
│ └── Resistor 15x15/
├── Program/
│ ├── lib/
│ ├── Master/
│ ├── Master_prova/
│ ├── backup1/
│ └── backup 2/
├── Simulation and circuits/
└── README.mdThis tree shows the main project directories. Individual KiCad libraries, 3D models, backup files, and simulation outputs are omitted for readability
Parts
101| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 100n | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C5, C6, C7, C10, C11, C14, C15, C16, C17, C18, C19, C20 |
| 7 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R20, R21, R22, R23, R24, R25, R29 |
| 5 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP2, TP4, TP5, TP6, TP8 |
| 4 | 10k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R2, R8, R9, R16 |
| 4 | 1N5817 | Diode_SMD:D_SMA | D1, D2, D7, D10 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_2.7mm_M2.5_DIN965_Pad | H1, H2, H3, H4 |
| 3 | 10n | Capacitor_SMD:C_0805_2012Metric | C21, C22, C23 |
| 3 | 8.2 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R17, R18, R19 |
| 3 | LED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D5, D6, D11 |
| 2 | 1000u | Capacitor_THT:CP_Radial_D13.0mm_P5.00mm | C3, C24 |
| 2 | 1N5817 | Diode_SMD:D_SOD-323_HandSoldering | D3, D4 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R10, R11 |
| 2 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R32 |
| 2 | 1u | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C12, C13 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R12, R13 |
| 2 | 27p | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C8, C9 |
| 2 | AO3400A | Package_TO_SOT_SMD:SOT-23 | Q3, Q4 |
| 2 | Conn_01x20 | Castellated_holes:2.54mm pin 1x20 | J2, J4 |
| 2 | TestPoint | TestPoint:TestPoint_Pad_D2.5mm | TP3, TP9 |
| 1 | 1 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R4 |
| 1 | 10 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | 100 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R26 |
| 1 | 100k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R33 |
| 1 | 100n | Capacitor_SMD:C_0805_2012Metric | C26 |
| 1 | 10A | Fuse:Fuseholder_Cylinder-5x20mm_Schurter_0031_8201_Horizontal_Open | F2 |
| 1 | 10u | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C4 |
| 1 | 10u | Capacitor_SMD:C_0805_2012Metric | C2 |
| 1 | 12 MHz | Crystal:Crystal_SMD_7050-4Pin_7.0x5.0mm | Y1 |
| 1 | 1A | Fuse_holder:0154.250DR | F1 |
| 1 | 200 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R28 |
| 1 | 200 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R3 |
| 1 | 20k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R7 |
| 1 | 330n | Capacitor_SMD:C_0805_2012Metric | C1 |
| 1 | 470 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6 |
| 1 | 470 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R14 |
| 1 | 5k6 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R15 |
| 1 | AMS1117-5.0 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U6 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | BZD27C10P | Diode_SMD:D_SMF | D9 |
| 1 | Connector_Conn_01x40_Female | Connector_FFC-FPC:Hirose_FH12-40S-0.5SH_1x40-1MP_P0.50mm_Horizontal | FPC1 |
| 1 | Debug | Castellated_holes:2.54mm pin 1x3 | J1 |
| 1 | EC11B15242AE | Trimmer_resistor:EC11B15242AE | S1 |
| 1 | FPC connector, 6 pins | Connector_FFC-FPC:Hirose_FH12-6S-0.5SH_1x06-1MP_P0.50mm_Horizontal | FPC2 |
| 1 | IRF540N | Package_TO_SOT_THT:TO-220-3_Vertical | Q1 |
| 1 | PC817 | Package_DIP:DIP-4_W7.62mm | U2 |
| 1 | RP2040 | MCU_RaspberryPi_and_Boards:RP2040-QFN-56 | U5 |
| 1 | Reset | Button_Switch_SMD:SW_SPST_B3U-1000P | SW2 |
| 1 | Resistor_Hotplate | MK1000:MK1000_P10mm_1x02 | J9 |
| 1 | S8050 | Package_TO_SOT_SMD:SOT-23 | Q7 |
| 1 | S8550 | Package_TO_SOT_SMD:SOT-23 | Q8 |
| 1 | Therm | Connector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | J5 |
| 1 | USB_C | USB_C_4_pin:USB_C_4_pin | J3 |
| 1 | Usb_boot | Button_Switch_SMD:SW_SPST_B3U-1000P | SW1 |
| 1 | V_IN | MK1000:MK1000_P10mm_1x02 | J8 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U4 |
More from dario0603/Hotplate
1Similar boards
- 2 layers99.1 × 99 mm
XDuinoRail Debug
chatelao/xDuinoRail-Decoder
The friendly decoder development plattform for model railroad tinkers.
170 partsAGPL-3.0 - 4 layers98 × 124.4 mm
Piberry.beepy
CarbonComputers/Piberry-12
PiBerry v12 marks the final and most refined revision of the PiBerry handheld Linux terminal. Designed with both form and function in mind, this version brings together the best elements of previous iterations while…
132 parts9MIT - 2 layers90.7 × 55.4 mm
H bridge V3
ambadran/Revolute_Joint
Optimal Cheap Robotic Actuator allowing high Torque and moderate Speed. Allow PRECISE Absolute, Speed and Torque Control. Using 3D-printed Cycloidal Drive, Custom PCB and LQR Control Algorithm.
57 parts - 2 layers99.5 × 99.5 mm
Carico elettronico
dario0603/electronic_load
Un progetto open-source per la progettazione e simulazione di un Carico Elettronico Bipolare (Electronic Load), ideato per il test e la caratterizzazione di alimentatori, batterie e circuiti di potenza.
92 parts - 2 layers54.3 × 16 mm
DC Motor Driver
ambadran/PCB-Manufacturer
A CNC machine with a kinematic mounting mechanism and customized GRBL Firmware to allow automated end-effector change; Allowing access to all the tools needed to create a PCB without human intervention.
13 parts2 - 2 layers100 × 100 mm
- 4 layers60 × 56.1 mm
- 4 layers60 × 56.1 mm
AvionicsPower
esb8/AvionicsPower
PCB of a Power Management and supply board for an Avionics stack.
82 parts2
Questions
What parts does the Controller use?
101 parts, built around the RP2040, W25Q128JVSIQ, AMS1117-5.0 and AP2112K-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Controller KiCad files?
From the dario0603/Hotplate repository on GitHub, at the commit this page was made from: the board is Kicad/Control board/Control board v1.2/Controller.kicad_pcb and its schematic Kicad/Control board/Control board v1.0/Controller.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Controller design in my own project?
Its repository states no licence, so its author keeps all rights: ask dario0603 before reusing the design.