
Vs1053-waveblaster se
ivop/vs1053-waveblaster
New WaveBlaster Daughterboard based on the VS1053 chip

New WaveBlaster Daughterboard based on the VS1053 chip
Vs1053-waveblaster is an open-source printed circuit board by ivop, from the ivop/vs1053-waveblaster repository on GitHub. It is a 2-layer board of 99.1 × 49.5 mm with 35 parts on 37 nets, routed with 227 tracks and 16 vias.
It is built around the VS1053B-L, LM1117-3.3V and BSS138. Its parts include 19 capacitors, 10 resistors, 3 ICs, 1 transistor and 1 connector. It belongs with the audio and music boards of this library.
By using a vs1053/vs8053, we present to you an ideal, low-cost, easy to solder, some what compact and open source WaveBlaster module.
Introducing VLSi SynthRoarer.

*Support General Midi with 128 GM1 instruments 61 GM2 Bank 0 precussion sounds up to 64 notes polyphony and stereo output @48Khz 16bit

Here is a sample from chip manufacture.
http://www.vlsi.fi/fileadmin/software/VS10XX/vs1053mid.mp3
It's been tested on a old ESS 688 audiodrive sound card.
REV B and REV A is in gergber/old stable.7z
REV C IS BASICALLY REV B,their schematic is the same.
REV A = vs1053-waveblaster
REV C = vs1053-waveblaster-se
Here's a view of it been fully assembled and not been. (It says REV C, but it's actually REV B).
*Look,it is working on my soundcard.

*a. It is your choice to use crystal or oscillator.
*b. Both vs8053 and vs1053 can be used. There're no diffience in the MIDI implementation. Just buy the cheapest one.

*All values are printed on the silkscreen.
Check out another waveblaster project: https://github.com/ivop/cs9236-waveblaster
1.Fully SMT-ized?(Maybe REV D?)
2.Get a proper logo?(Maybe REV D?)
3.Write a bom list?(How about right now!)

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100n | Capacitors_ThroughHole:C_Disc_D3_P2.5 | C5, C6, C7, C8, C9, C10, C11, C12, C13, C14, C19 |
| 4 | 10u | Capacitors_ThroughHole:C_Radial_D5_L6_P2.5 | C1, C2, C3, C4 |
| 2 | 0 | Resistors_ThroughHole:Resistor_Horizontal_RM10mm | R1, R2 |
| 2 | 100K | Resistors_ThroughHole:Resistor_Horizontal_RM10mm | R3, R8 |
| 2 | 10K | Resistors_ThroughHole:Resistor_Horizontal_RM10mm | R9, R10 |
| 2 | 10n | Capacitors_ThroughHole:C_Disc_D3_P2.5 | C17, C18 |
| 2 | 20 | Resistors_ThroughHole:Resistor_Horizontal_RM10mm | R6, R7 |
| 1 | 10 | Resistors_ThroughHole:Resistor_Horizontal_RM10mm | R5 |
| 1 | 1u | Capacitors_ThroughHole:C_Disc_D3_P2.5 | C15 |
| 1 | 47n | Capacitors_ThroughHole:C_Disc_D3_P2.5 | C16 |
| 1 | 4K7 | Resistors_ThroughHole:Resistor_Horizontal_RM10mm | R4 |
| 1 | BSS138 | TO_SOT_Packages_SMD:SOT-23 | Q1 |
| 1 | LM1117-1.8V | TO_SOT_Packages_SMD:SOT-223 | U2 |
| 1 | LM1117-3.3V | TO_SOT_Packages_SMD:SOT-223 | U1 |
| 1 | OSC5032 | footprints:Crystal_SMD_5032-4Pin_5.0x3.2mm | X1 |
| 1 | VS1053 | Housings_QFP:LQFP-48_7x7mm_Pitch0.5mm | U3 |
| 1 | WAVEBLASTER | Pin_Headers:Pin_Header_Straight_2x13 | CON1 |

ivop/vs1053-waveblaster
New WaveBlaster Daughterboard based on the VS1053 chip


UzixLS/zxevo1010-board
10x10cm PCB variant of ZX-Evolution project for G738/G706 enclosure

karawin/Ka-Radio
A wifi webradio with only low cost boards ESP8266 and VS1053 by Jp Cocatrix


SL-RU/sdmplayer
This is sources of my DIY music player based on STM32 MCU and VS1053 codec



It measures 99.1 × 49.5 mm and has 2 copper layers, 1.6 mm thick.
35 parts, built around the VS1053B-L, LM1117-3.3V and BSS138. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the ivop/vs1053-waveblaster repository on GitHub, at the commit this page was made from: the board is kicad/vs1053-waveblaster.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask ivop before reusing the design.