Mtt final
itsmevjnk/MelbourneTrainTracker
Melbourne Train Tracker project repository (SIT210, T1/2025)
Melbourne Train Tracker project repository (SIT210, T1/2025)
MelbourneTrainTracker is an open-source printed circuit board by itsmevjnk, from the itsmevjnk/MelbourneTrainTracker repository on GitHub. It is a 2-layer board of 251.6 × 177.8 mm with 1,071 parts on 621 nets, routed with 21,017 tracks and 3,653 vias.
It is built around the AIP74HC125SA14.TR, ESP32-S3-WROOM-1-N8R8 and AW20216SQNR, with the TFW11-N1S1-2000-A, USBLC6-2SC6 and XC6220B331MR among its other parts. Its parts include 738 diodes, 218 resistors, 78 capacitors, 17 ICs and 5 connectors. It belongs with the ESP32 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 735 | XL-B1010RGBT-HF | custom_footprints:LED_RGB_Xinglight-1010 | D1, D10, D11, D100, D101, D102, D103, D104, D105, D106, D107, D108, D109, D110, D111, D112 +719 |
| 124 | 30R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R10, R11, R100, R101, R103, R104, R106, R107, R109, R110, R112, R113, R115, R116, R118 +108 |
| 62 | 47R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R12, R102, R105, R108, R111, R114, R117, R120, R123, R126, R129, R132, R135, R138, R141, R144 +46 |
| 37 | 0.1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C11, C12, C15, C17, C18, C21, C23, C24, C27, C29, C30, C33, C35, C36, C39 +21 |
| 25 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R184, R185, R186, R187, R188, R189, R190, R191, R192, R196, R197, R198, R199, R200, R201, R202 +9 |
| 23 | 1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C5, C10, C14, C16, C20, C22, C26, C28, C32, C34, C38, C40, C44, C46, C50 +7 |
| 18 | 10uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C7, C13, C19, C25, C31, C37, C43, C49, C55, C61, C70, C72, C73, C74, C76 +2 |
| 11 | AW20216S | custom_footprints:QFN-44-1EP_5x5mm_P0.4mm_EP2.45x2.45mm | U1, U2, U3, U4, U5, U6, U7, U8, U9, U10, U11 |
| 4 | 5.1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R205, R206, R217, R218 |
| 3 | 470R | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R208, R209, R216 |
| 3 | 74LS125 | Package_SO:SO-14_3.9x8.65mm_P1.27mm | U12, U13, U14 |
| 3 | LED | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D730, D733, D736 |
| 2 | SW_Push | Button_Switch_SMD:SW_Push_1P1T_NO_E-Switch_TL3301NxxxxxG | SW1, SW2 |
| 2 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP1, JP2 |
| 1 | Conn_01x09 | Connector_PinHeader_2.54mm:PinHeader_1x09_P2.54mm_Vertical | J2 |
| 1 | Conn_02x04_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J4 |
| 1 | ESP32-S3-WROOM-1 | RF_Module:ESP32-S3-WROOM-1 | U15 |
| 1 | LOGO | custom_footprints:logo | G*** |
| 1 | LOGO | custom_footprints:oshw_logo | G*** |
| 1 | Micro_SD_Card_Det1 | custom_footprints:TFW11-N1S1-2000-A | J3 |
| 1 | SSD1306 OLED | custom_footprints:HS96L03W2C03 | J5 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U16 |
| 1 | USB_C_Receptacle_USB2.0_16P | custom_footprints:ShouHan-USBC-16P-2MD | J1 |
| 1 | XC6220B331MR | Package_TO_SOT_SMD:SOT-23-5 | U17 |
The 1,062 most common of 1,071 parts.
itsmevjnk/MelbourneTrainTracker
Melbourne Train Tracker project repository (SIT210, T1/2025)


Tay0710/Design_S1_006
This project integrates hardware, firmware, and design elements to develop a fully functional autonomous 3D mapping drone system.


EDrTech/ILM139C
ILM139C Is an RGB LED module with a matrix of 13x9 RGB LEDs. It is based on the IS31FL3741A LED matrix driver, which provides an i2c interface for full control of individual LEDs which is accessible with a standard…



enkhbold470/iron-node
ESP32-S3 industrial gateway: W5500 Ethernet, isolated RS-485 (ADM2587E), CAN, 9-36 V input. 4-layer KiCad 10 board.

enkhbold470/pd-brick
USB-C Power Delivery bench supply: STUSB4500 sink, LM5176 buck-boost, INA228 monitor, 1.2-22 V set over I2C by an ESP32-S3. 4-layer KiCad 10 board.
It measures 251.6 × 177.8 mm and has 2 copper layers, 1.69 mm thick.
1,071 parts, built around the AIP74HC125SA14.TR, ESP32-S3-WROOM-1-N8R8, AW20216SQNR and TFW11-N1S1-2000-A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the itsmevjnk/MelbourneTrainTracker repository on GitHub, at the commit this page was made from: the board is Hardware/Rev2/Rev2.kicad_pcb and its schematic Hardware/Rev1/mtt.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask itsmevjnk before reusing the design.