2 layers150 × 100 mm
Rps01
Kenkneeshio/SeniorDesign-Team9
This is SDSU's Spring 2023 Senior Design A Team 9: Robot Power System GitHub
182 parts
2 layers29.6 × 28 mm
TakenTracker
issaimaru/TakenTracker- Size
- 29.6 × 28 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 19
- Nets
- 26
- Pads
- 67
- Tracks, vias
- 100, 55
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 2 Nov 2025
- Updated
- 4 Nov 2025
Overview
TakenTracker is an open-source printed circuit board by issaimaru, from the issaimaru/TakenTracker repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 29.6 × 28 mm with 19 parts on 26 nets, routed with 100 tracks and 55 vias.
It is built around the ICM-42605 and B0540W-7-F-HXY. Its parts include 4 diodes, 4 connectors, 3 capacitors, 3 resistors and 2 ICs. It belongs with the nRF52 and nRF5x boards of this library.
Main components
2README
README.mdTakenTracker
Parts
19| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 1k | Resistor_SMD:R_0402_1005Metric | R1, R2, R3 |
| 1 | + | Connector_Wire:SolderWirePad_1x01_SMD_1x2mm | J1 |
| 1 | - | Connector_Wire:SolderWirePad_1x01_SMD_1x2mm | J2 |
| 1 | 0.1u | Capacitor_SMD:C_0402_1005Metric | C2 |
| 1 | 10u | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 2.2u | Capacitor_SMD:C_0402_1005Metric | C3 |
| 1 | B | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | B0540W-7-F | Diode_SMD:D_SOD-123 | D1 |
| 1 | C2Q 250 | Fuse:Fuse_0603_1608Metric | F1 |
| 1 | G | LED_SMD:LED_0603_1608Metric | D3 |
| 1 | ICM-42605 | Package_LGA:LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y | U1 |
| 1 | LOGO | LOGO | G*** |
| 1 | NFC1 | Connector_Wire:SolderWirePad_1x01_SMD_1x2mm | J3 |
| 1 | NFC2 | Connector_Wire:SolderWirePad_1x01_SMD_1x2mm | J4 |
| 1 | R | LED_SMD:LED_0603_1608Metric | D4 |
| 1 | SK-12D11VG3 | TakenTracker_footprint:SK-12D11VG3 | SW1 |
| 1 | XIAO-nRF52840-SMD | XIAO:XIAO-nRF52840-SMD | U2 |
Similar boards
- 4 layers66.3 × 40.2 mm
Cm4 drone
dridri/bcflight
Raspberry Pi based drone flight controller and remote control
56 parts175GPL-3.0 - 4 layers40 × 55 mm
CopterCat cm4
matveylapin/CopterCat_cm4
Полётный контроллер для стандарта FMU-v6u. Обычно на дронах для программирования устанавливают полётный контроллер, одноплатный компьютер и иногда arduino.
164 parts3Apache-2.0 - 4 layers112.7 × 122 mm
- 6 layers46.5 × 47.2 mm
NAVCORE SoOP
kfilipekk/iridium_drone
STM32H743 flight controller that navigates without GPS from Iridium satellite Doppler
217 parts2MIT - 4 layers10 × 32 mm
- 4 layers32.5 × 22 mm
Open PWM Gyro
jerinabr/Open-PWM-Gyro-Hardware
PWM gyro for fixed wing RC planes. Meant to be connected to an ELRS RX or other RX that outputs CRSF control data.
27 parts1 - 4 layers41.6 × 42 mm
IEE Drone 2026
CalebJM04/IEEE-2026-UAV
Drone project for IEEE 2026 UAV. Primarily created by Caleb Murray
54 parts
Questions
How big is the TakenTracker PCB?
It measures 29.6 × 28 mm and has 2 copper layers, 1.6 mm thick.
What parts does the TakenTracker use?
19 parts, built around the ICM-42605 and B0540W-7-F-HXY. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the TakenTracker KiCad files?
From the issaimaru/TakenTracker repository on GitHub, at the commit this page was made from: the board is TakenTracker.kicad_pcb and its schematic NFC_Antenna.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the TakenTracker design in my own project?
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).