

Serpente
Varios
- Size
- 24 × 22 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 31
- Nets
- 42
- Pads
- 127
- Tracks, vias
- 272, 35
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 7 Dec 2018
- Updated
- 12 Feb 2022
Overview
Serpente is an open-source printed circuit board by hulkco, from the hulkco/Varios repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 24 × 22 mm with 31 parts on 42 nets, routed with 272 tracks and 35 vias.
It is built around the ATSAMD21E18A-AF and GD25Q32CNIGR. Its parts include 8 resistors, 4 capacitors, 3 ICs, 3 diodes and 3 connectors. It belongs with the SAM D and SAM boards of this library.
Main components
2ATSAMD21E18A-AF
TQFP-32(7x7)-40℃~+125℃ 1.62V~3.6V 10bit 12bit 256KB 26 32 Bit 32KB 48MHz ARM Cortex-M0+ Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)GD25Q32CNIGR
USON-8(3x4)100,000 cycles 120MHz 150ms@(32KB) 1uA 2.7V~3.6V 20 Years 32Mbit 600us SPI USON-8(3x4) NOR FLASH ROHSGigaDevice Semicon BeijingNOR FLASH
README
README.mdVarios
Parts
31| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 150R | Resistor_SMD:R_0603_1608Metric | R2, R3 |
| 2 | 1uF | Capacitor_SMD:C_0603_1608Metric | C1, C4 |
| 2 | 22R | Resistor_SMD:R_0603_1608Metric | R7, R8 |
| 2 | 5.1K | Resistor_SMD:R_0603_1608Metric | R4, R5 |
| 2 | D_Schottky_Small | Diode_SMD:D_SOD-323_HandSoldering | D1, D2 |
| 1 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C2 |
| 1 | 10uF | Capacitor_SMD:C_0603_1608Metric | C3 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 360R | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | ATSAMD21E18A | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.6x3.6mm | U3 |
| 1 | Conn_GPIO | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | Conn_Power | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | GD25Q32CNIGR | Package_SON_Extra:USON-8_3x4mm_P0.8mm | U1 |
| 1 | LED_ARGB | LED_SMD:LED_Cree-PLCC4_2x2mm_CW | D3 |
| 1 | LOGO | serpente:qrcode | G*** |
| 1 | MCP1700-3302E_SOT23 | Package_TO_SOT_SMD:SOT-23 | U2 |
| 1 | SW_RESET | Button_Switch_SMD:SW_SPST_B3U-1000P | SW1 |
| 1 | TP_GND | TestPoint:TestPoint_Pad_D1.0mm | TP4 |
| 1 | TP_SWCLK | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | TP_SWDIO | TestPoint:TestPoint_Pad_D1.0mm | TP2 |
| 1 | TP_USB_D+ | TestPoint:TestPoint_Pad_D1.0mm | TP6 |
| 1 | TP_USB_D- | TestPoint:TestPoint_Pad_D1.0mm | TP5 |
| 1 | TP_VDD | TestPoint:TestPoint_Pad_D1.0mm | TP3 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB_Extra:USB_C_Receptacle_GT-USB-7010 | J1 |
The 29 most common of 31 parts.
More from hulkco/Varios
12- 2 layers35.6 × 66.5 mm

- 2 layers38.6 × 69.5 mm

- 16 layers88.3 × 64.5 mm

- 2 layers43.6 × 41.1 mm

- 2 layers108 × 67.2 mm

- 2 layers35.6 × 66.5 mm

- 2 layers50 × 50 mm

- 2 layers

- 2 layers68.6 × 53.3 mm

- 2 layers85.7 × 92.7 mm

- 2 layers40.6 × 38.1 mm

- 2 layers205.3 × 104.2 mm

Similar boards
- 2 layers25.4 × 22 mm

Fidi micro
omzlo/fidi-hardware
FIDI is a small development board running Adafruit's CircuitPython, featuring 6 terminal block connectors and a qwiic connector, designed for fast prototyping.
32 parts1 - 2 layers24.8 × 22 mm

- 4 layers17.5 × 30.5 mm

ESP32 S3 CAM wifi
HexSense-MIT/HS_ESP32_CAM_module
A custom designed USB camera module, with ESP32-S3R8 + OV2640. This will be used for the HexSenseCAM payload.
52 parts1 - 6 layers40 × 16 mm

- 4 layers37.6 × 30.6 mm

Bias generator LT8362
OpenSiPM/sipm-bias-control
Single channel silicon photomultipliers for high-speed fluorescence imaging
61 parts44 - 4 layers44.5 × 34.9 mm

Eclair
upbeatcarri/eclair
Pocket device for taking quick notes, acting as a USB keyboard for PC sync etc., with custom apps samd21, tinygo
56 parts25 - 4 layers100 × 100 mm

Pi TX 35W PA V2
M0LTE/pi-transceiver
An attempt to build a complete ham radio transceiver around a Raspberry Pi
185 parts15 - 4 layers33.6 × 18 mm

Cap sense ctrl
gregdavill/cap-sense-flex
A prototype of a flex measuring sensor. Based off: https://dl.acm.org/doi/10.1145/3313831.3376269
43 parts11
Questions
How big is the Serpente PCB?
It measures 24 × 22 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Serpente use?
31 parts, built around the ATSAMD21E18A-AF and GD25Q32CNIGR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Serpente KiCad files?
From the hulkco/Varios repository on GitHub, at the commit this page was made from: the board is Serpente/serpente_hw-master/serpente.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Serpente design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).