Skip to the content
4 layers37.6 × 30.6 mmBias generator LT8362, the printed circuit board in 3D

Bias generator LT8362

OpenSiPM/sipm-bias-control44

Single channel silicon photomultipliers for high-speed fluorescence imaging

Size
37.6 × 30.6 mm
Copper layers
4
Thickness
1.59 mm
Parts
61
Nets
57
Pads
200
Tracks, vias
284, 69
Pours
9
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
25 Oct 2019
Updated
6 Oct 2026

Overview

Bias generator LT8362 is an open-source printed circuit board by OpenSiPM, from the OpenSiPM/sipm-bias-control repository on GitHub. It is a 4-layer board of 37.6 × 30.6 mm with 61 parts on 57 nets, routed with 284 tracks and 69 vias.

It is built around the ATSAMD21E18A-AF, MIC5317-3.3YM5-TR and RT9072BGB, with the 1N4148WS and PMEG6030EP among its other parts. Its parts include 18 capacitors, 15 resistors, 6 ICs, 4 connectors and 2 diodes. It belongs with the SAM D and SAM boards of this library.

Main components

5

README

README.md

Introduction

The OpenSiPM project aims to design high performance, low cost detectors for fluorescense microscopy.

overview

The sipm-bias-control repository contains the KiCAD design files for a high dynamic range silicon photomultiplier (SiPM) transimpedance amplifier, power suppply, and bias generator designed by Eben Olson and Michael Giacomelli. The repository is organized into separate folders for each component, with bias-control-lt8362 containing the design files for the high voltage bias generator, power-supply/power-supply-alt containing two equivilent opamp power supply boards, and the tiav3_s1XXXX folders containing high dynamic range transimpedance amplifiers using current domain pole zero cancellation for several models of Hamamatsu SiPM. The bias generator, power supply and a transimpedance amplifier PCB stack together to build a single detector that can be mounted in a conventional SM1 lens tube. In addition, the firmware folder contains the firmware required to run the bias-control microcontroller.

Compared to conventional PMT detectors used in many laser scanning fluorescense microscopes, SiPMs have some advantages, including low cost, high durability, higher QE at long wavelengths, and extremely high dynamic range. The amplifier design presented here is specifically optimized for maximizing dynamic range with a saturation power in excess of 40-100 billion photons per second (depending on model), enabling high imaging rates without saturation. The disadvantage of the SiPM detectors is relatively high dark current, which makes them less suitable for low speed scanning systems. However, at high pixel rates, they obtain superior sensitivity to PMTs.

performance

Image of bias generator

The performance of this detector design is evaluated in the manuscript "Ultrahigh‑speed point scanning two‑photon microscopy using high dynamic range silicon photomultipliers" by Vincent Ching‑Roa et al. The manuscript can be accessed at no charge here: https://www.nature.com/articles/s41598-021-84522-0

bias-control-lt8362

This PCB is responsible for generating the high voltage (~50-60V) required to operate a SiPM, receiving USB commands using a SAMD21 microcontroller, and distributing +5v power from USB to the other boards which stack onto it. There are additionally a programming header used to initially flash the Arduino bootloader.

See: bias-control-lt8362. Bill of materials

Image of bias generator

power-supply

This PCB takes the +5v from USB and converts to low noise +3.3v and -4.5v used by the opamps. The asymetric voltages are because the negative rail has a much larger impact on dynamic range, making optimization of the negative voltages a lot more important. A list of components required can be viewed online in the interactive power-supply bill of materials

Image of power supply board

Due to the global semiconductor shortage making regulator ICs hard to get, there is also an alternative power supply design which uses easier to obtain ICs. These are slightly more expensive and (on paper) slightly better. In practice there should be little difference in performance and no reason to prefer one design over the other aside from component availability.

tiav3

This PCB receives bias and supply voltages from the other boards and emits amplified RF out over an SMA or SMB connector. A SiPM is mounted in the center of the PCB, which will mount in an SM1 lens tube to simplify alignment with an existing microscope. The transimpedance amplifier implements current domain pole zero cancellation (PZC) (see: Pole Zero Cancellation), where an inductive current divider is used to separate the slow SiPM recharge current from the fast capacitive spike generated by a single photon detection. Following the divider, a transimpedance amplifier converts to voltage and then drives the 50 ohm SMA or SMB connector. An additional offset correction function is provided using the microcontroller on the bias-control board, enabling either zeroing the amplifier zero point, or shifting the zero point to positive voltages to extend dynamic range.

The use of current domain PZC has several advantages over conventional methods. First, since the slow component of the SiPM response is canceled prior to amplification, the dynamic range is extended by the same factor as the PZC attenuates, in this case, 10-fold. Second, the impedance of the current divider isolates the amplifier from the large capacitance of the SiPM, resulting in higher bandwidth and much greater stability. Finally, this design is very simple, requiring only one opamp.

tiav3 bill of materials

Image of TIA board

selection of SiPM model

Currently 3 families of SiPM are supported, the red-enchanced S14420, the blue-enchanced S13360 and the blue-enchanced, high dynamic range S14160. Within each family multiple sizes of SPAD cell are available, with larger cells having higher photon detection efficency but much lower dynamic range due to fewer SPADs and larger SPADs being slower. For example, doubling the SPAD cell size on the S14420 increases photon detection efficency by ~1.3 but reduces the dynamic range from 40B photons/s to just 5B photons/s. The older S13360 is available in larger SPAD sizes (50 and 75 micron) that have very high detection efficency. The newer S14160 is available in very small SPAD sizes enabling higher dynamic range. Both are reasonable choices below 550 nm, with the S14420 being a better choice above that.

Each SPAD size requires a unique PZC configuration. By default the S14420 BOM is configured for 25 microns, the S14160 for 15 microns and the S13360 for 50 microns. Where the values are known the alternative PZC configuration is in the schematic, so be sure to change that if you buy a different SPAD-size SiPM.

firmware

The firmware folder includes both the Arudino bootloader for the SAMD21 microcontroller and a basic program for controlling the bias and offset voltages. See firmware setup instructions.

The actual firmware commands are sent over the virtual com port to the microcontroller. "On" turns on the bias generator. "Off" turns it off. "gain 1000" sets the gain to 1000". "gain?" returns the current gain. "offset 150" sets the tia offset to 150 units. "help?" prints a list of supported commands. The bias generator can also be calibrated using the "calibration" command if exact voltages (beyond what is possible with resistor tolerances) are required. The firmware can also be configured for the standard LT8362 design (max voltage of 60V) or a higher voltage configuration using the LT8361.

low pass filter

The updated tiav3 design incorporates a low pass filter that can be configured for typical resonant or polygon scanning applications.

It is very strongly recommended to adjust the bandwidth of the filter to match your scanning speed and objective. The wrong banwdith will reduce sensitivity (if too high) or resolution (if too low). See Low-Pass-Filter for details. Suggested filter configurations are provided in the TIA schematics.

To find the right cutoff for your microscope, use the low pass filter bandwidth calculator, which computes the recommended bandwidth from wavelength, objective NA, field of view and scan rate and suggests the nearest filter configuration.

optical design

Sample Zemax optical design files are provided in the optics demonstrating one possible configuration for illuminating the SiPM detector in a conventional two photon or confocal microscope.

ordering boards

Go to https://jlcpcb.com, https://www.seeedstudio.com/fusion_pcb.html or the service of your choice, upload the Gerber files, and pay. At present prices, 10 boards will cost about 10-25 dollars shipped to most of the world.

Gerber files can be generated from KiCAD using 'File -> Plot' or using the JLCPCB plugin.

board assembly

The easiest way to assemble these boards is using solder paste and a reflow oven. The inexpensive T-962 clones on Amazon or even a hotplate will work fine for simple boards such as this. Alternatively, they can also be manually soldered. The design uses a mix of 0402 and larger parts, which can be challenging to solder with the wrong tools. A ~0.6-1.2mm diameter chissel type soldering tip, high quality no clean flux such as amtech nc-559-v2-tf, 40/60 lead solder, and good tweezer such as Hakko CHP 5-SA or equivilent are strongly recommended if reflow is not used. These are inexpensive and readily available on Amazon.

If you're going to make lots of boards, paying for assembly of the passive and common components and then adding the detectors yourself might be worthwhile. The BOM for the bias generator has been selected such that nearly all components are available at JLCPCB.

Parts

61
QtyValueFootprintReferences
15TestPointTestPoint:TestPoint_Pad_D1.0mmHV1, HV2, HV3, HV4, HV5, HV6, HV7, HV8, HV9, TP_1.22V1, TP_BoostEnable1, TP_GND1, TP_GND2, TP_MCP_Out1, TP1
72.2uCapacitor_SMD:C_0603_1608MetricC2, C7, C9, C10, C14, C17, C18
52.2uFCapacitor_SMD:C_1206_3216MetricC5, C6, C8, C11, C13
45.1kResistor_SMD:R_0603_1608MetricR1, R3, R7, R10
339kResistor_SMD:R_0603_1608MetricR12, R15, R16
21MResistor_SMD:R_0603_1608MetricR4, R5
222uCapacitor_SMD:C_0603_1608MetricC1, C4
25.1kfootprints:R_0603_1608MetricR8, R9
110nCapacitor_SMD:C_0603_1608MetricC16
11N4148WSDiode_SMD:D_SOD-323FD2
11uCapacitor_SMD:C_0603_1608MetricC3
12.2nCapacitor_SMD:C_0603_1608MetricC15
125pFCapacitor_SMD:C_0603_1608MetricC12
13.3uHfootprints:SRP05204R7KL1
136.5kResistor_SMD:R_0603_1608MetricR11
139k (LT8361) / 52.3k (LT8362)Resistor_SMD:R_0603_1608MetricR6
15Resistor_SMD:R_0603_1608MetricR13
169.8kResistor_SMD:R_0603_1608MetricR2
1ATSAMD21E18A-AFfootprints:ATSAMD21E18A-AFIC2
1Conn_01x04Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical_SMD_Pin1RightJ2
1Conn_01x06footprints:PinHeader_2x03_P2.54mm_VerticalJ3
1ISPfootprints:POGO_ISPJ1
1LT8361EMSE/LT8362EMSEfootprints:LT8364IMSE-PBFIC1
1MCP47FEB22A2-E_STfootprints:SOP65P640X120-8NIC4
1MCP6C02T-020E/CHYPackage_TO_SOT_SMD:SOT-23-6U3
1MIC5317-3.3YM5-TRfootprints:MIC5317-3.3YM5-TRU1
1PMEG6030EPDiode_SMD:D_SOD-128D3
1RT9072BPackage_TO_SOT_SMD:SOT-23-5U2
1USB_C_Receptacle_USB2.0_16Pfootprints:CUI_UJ20-C-V-C-2-SMT-TR_fixedV2J4

More from OpenSiPM/sipm-bias-control

5
  • 2 layersTia, the printed circuit board in 3D

    Tia

    OpenSiPM/sipm-bias-control

    Single channel silicon photomultipliers for high-speed fluorescence imaging

    26 parts44
  • 4 layersTiav3 s13360 3030VE, the printed circuit board in 3D

    Tiav3 s13360 3030VE

    OpenSiPM/sipm-bias-control

    Single channel silicon photomultipliers for high-speed fluorescence imaging

    24 parts44
  • 4 layersTiav3 s14160, the printed circuit board in 3D

    Tiav3 s14160

    OpenSiPM/sipm-bias-control

    Single channel silicon photomultipliers for high-speed fluorescence imaging

    22 parts44
  • 4 layersTiav3, the printed circuit board in 3D

    Tiav3

    OpenSiPM/sipm-bias-control

    Single channel silicon photomultipliers for high-speed fluorescence imaging

    21 parts44
  • 2 layers8.8 × 22.1 mmPsu, the printed circuit board in 3D

    Psu

    OpenSiPM/sipm-bias-control

    Single channel silicon photomultipliers for high-speed fluorescence imaging

    14 parts44

Similar boards

  • 4 layers51 × 59 mmPlaqchek sipm sens, the printed circuit board in 3D

    Plaqchek sipm sens

    PLAQCHEK/Hardware_Design

    circuit simulations, schematics, PCB design files

    99 parts
  • 4 layers97 × 97.4 mmQEdge UI, the printed circuit board in 3D

    QEdge UI

    qinno/qEdge-UI

    qedge+ is the industry's low power design alternative to the standard PC approach. qEdge-UI is part of qEdge+ and consists of a RaspBerry Pico with LCD, touch screen and keys and an 868MHz LoRa radio module.

    170 parts3
  • 2 layers80 × 50 mmBlitzortung AS3935, the printed circuit board in 3D

    Blitzortung AS3935

    patkan/lightning-detector

    Lightning Detector ethernet sensor node and server based on AS3935 - this project is discontinued

    81 parts1GPL-2.0
  • 4 layers86 × 29.9 mmGeiger probe, the printed circuit board in 3D

    Geiger probe

    bartkepl/CanGeigerProbe

    Polowa sonda promieniowania jonizującego z miniaturową lampą Geigera-Müllera, komunikująca się cyfrowo przez CAN 2.0B.

    116 partsMIT
  • 4 layers76 × 29.9 mmGnss node, the printed circuit board in 3D

    Gnss node

    bartkepl/CanGnssNode

    Polowy węzeł pozycyjny z modułem GNSS Quectel L76-L (GPS/GLONASS/Galileo/QZSS) i czujnikiem orientacji (akcelerometr + magnetometr), komunikujący się cyfrowo przez CAN 2.0B.

    141 partsMIT
  • 4 layers120 × 75 mmControlPanel, the printed circuit board in 3D

    ControlPanel

    bartkepl/ControlPanelV3S

    V3S CAN-bus control panel - KiCad hardware

    327 partsMIT

Questions

How big is the Bias generator LT8362 PCB?

It measures 37.6 × 30.6 mm and has 4 copper layers, 1.59 mm thick.

What parts does the Bias generator LT8362 use?

61 parts, built around the ATSAMD21E18A-AF, MIC5317-3.3YM5-TR, RT9072BGB and 1N4148WS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Bias generator LT8362 KiCad files?

From the OpenSiPM/sipm-bias-control repository on GitHub, at the commit this page was made from: the board is bias-control-lt8362/bias_generator_LT8362.kicad_pcb and its schematic bias-control-lt8362/bias_generator_LT8362.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Bias generator LT8362 design in my own project?

Its repository states no licence, so its author keeps all rights: ask OpenSiPM before reusing the design.