4 layers43.9 × 18.8 mm
2 layers72 × 48 mm
Tareknano
heyitsmeyo/ArduinoWifi-customA cutsom arduino uno pcb design that supports Wi-Fi and SD card reader
- Size
- 72 × 48 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 50
- Nets
- 68
- Pads
- 286
- Tracks, vias
- 999, 231
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 30 Mar 2025
- Updated
- 30 Mar 2025
Overview
Tareknano is an open-source printed circuit board by heyitsmeyo, from the heyitsmeyo/ArduinoWifi-custom repository on GitHub. It is a 2-layer board of 72 × 48 mm with 50 parts on 68 nets, routed with 999 tracks and 231 vias.
It is built around the ATMEGA328P-AU, 74LVC125APW,118-JSM and ESP-01, with the CH340G, LM1117DT-5.0 and SS13 among its other parts. Its parts include 15 resistors, 13 capacitors, 6 connectors, 5 ICs and 5 diodes. It belongs with the ESP8266 and AVR (ATmega, ATtiny) boards of this library.
Main components
6
ATMEGA328P-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
74LVC125APW,118-JSM
SOP-14SOP-14 Buffers, Drivers, Receivers, Transceivers ROHSJSMSEMIBuffers, Drivers, Receivers, Transceivers
ESP-01
插件-20℃~+85℃ -90dBm 16dBm 2.4GHz 20mA 300mA 3V~3.6V 802.11b/g/n ESP8266 Chip Over-the-air (OTA) update UART 插件 WiFi Modules ROHSAi-ThinkerWiFi Modules
CH340G
SOP-16-40℃~+85℃ 2Mbps 3.3V、5V USB 2.0 USB to UART SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB Converters
LM1117DT-5.0
TO-2520.003%Vout 0℃~+125℃@(Tj) 1 1.3V@(800mA) 10mA 15V 5V 75dB@(120Hz) 800mA Fixed Over Current Protection、Thermal Shutdown Positive TO-252 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
SS13
SMASchottky DiodesGOODWORK
README
README.mdArduinoWifi-custom
A cutsom arduino uno pcb design that supports Wi-Fi and SD card reader
if you like the project , you can donate us for more :
https://ko-fi.com/heyitsmeyoParts
50| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 1k | Resistor_SMD:R_0201_0603Metric | R1, R2, R3, R4, R5, R7, R8, R14 |
| 4 | 100nf | Capacitor_SMD:C_0201_0603Metric | C5, C11, C13, C15 |
| 4 | 22pf | Capacitor_SMD:C_0201_0603Metric | C1, C2, C3, C4 |
| 4 | 3.3k | Resistor_SMD:R_0201_0603Metric | R9, R10, R11, R12 |
| 4 | LED | LED_SMD:LED_0603_1608Metric | D1, D2, D3, D4 |
| 3 | 1uf | Capacitor_SMD:C_0201_0603Metric | C6, C8, C9 |
| 2 | 10k | Resistor_SMD:R_0201_0603Metric | R6, R15 |
| 2 | 4.7uf | Capacitor_SMD:CP_Elec_4x5.8 | C7, C10 |
| 2 | Conn_01x04_Socket | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J5, J6 |
| 2 | Conn_01x15_Pin | Connector_PinSocket_2.54mm:PinSocket_1x15_P2.54mm_Vertical | J3, J4 |
| 1 | 12Mhz | Crystal:Crystal_SMD_Abracon_ABM3-2Pin_5.0x3.2mm | Y2 |
| 1 | 2k | Resistor_SMD:R_0201_0603Metric | R13 |
| 1 | 502570-0893 | sd:MOLEX_502570-0893 | J7 |
| 1 | 74LVC125APW_118 | esp01:TSSOP14_SOT402-1_NEX | U4 |
| 1 | ATmega328P-A | Package_QFP:TQFP-32_7x7mm_P0.8mm | U2 |
| 1 | CH340G | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U1 |
| 1 | Crystal | Crystal:Crystal_SMD_Abracon_ABM3-2Pin_5.0x3.2mm | Y1 |
| 1 | ESP-01 | esp01:MODULE_ESP-01 | U5 |
| 1 | Fuse | Resistor_SMD:R_0603_1608Metric | F1 |
| 1 | LM1117DT-5.0 | Package_TO_SOT_SMD:TO-252-3_TabPin2 | U3 |
| 1 | SS13 | Diode_SMD:D_SMA | D5 |
| 1 | SW_Push | Button_Switch_SMD:SW_Tactile_SPST_NO_Straight_CK_PTS636Sx25SMTRLFS | SW1 |
| 1 | SW_Push_Dual | Button_Switch_THT:SW_PUSH_6mm | SW2 |
| 1 | SW_SPDT | Button_Switch_SMD:SW_SPDT_PCM12 | SW4 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Amphenol_10103594-0001LF_Horizontal | J1 |
Similar boards
- 2 layers87 × 79 mm
- 2 layers102 × 53.8 mm
STM32F407 Mega layout rev1.2.kicad pro
mazduino/stm32f407xxx-mega-layout
STMM32F407xxx Mega Layout. Made For Speeduino and RusEFI Firmware
94 parts1 - 2 layers99.9 × 70.5 mm
PCB puerta
yabo104/Electric_Door_With_ESP32_S3
This proyeject contains a hardware/firmware development for an electric door controller.
75 parts - 6 layers29 × 80.6 mm
BladeCore M54E
DvidMakesThings/HW_PDNode-600-Pro
The PDNode-600 is a professional-grade, 600W USB Power Delivery Unit designed specifically for compact 10-inch rack systems, targeting embedded developers, homelab enthusiasts, test benches, and smart infrastructure.
150 parts86AGPL-3.0 - 2 layers86 × 50 mm
- 2 layers90 × 90 mm
Ykts power
cansat-ptl/cubesat-boards
YKTSAT Kicad board files - mirror of https://git.yktaero.space/yktaero-dev/cubesat-boards
132 parts - 2 layers11.7 × 33.8 mm
RGB strip controller
eritbh/esp01-led-controller
Using the ESP-01 to control addressable RGB LED strips.
24 partsCC0-1.0
Questions
How big is the Tareknano PCB?
It measures 72 × 48 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Tareknano use?
50 parts, built around the ATMEGA328P-AU, 74LVC125APW,118-JSM, ESP-01 and CH340G. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Tareknano KiCad files?
From the heyitsmeyo/ArduinoWifi-custom repository on GitHub, at the commit this page was made from: the board is tareknano/tareknano/tareknano.kicad_pcb and its schematic tareknano/tareknano.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Tareknano design in my own project?
Its repository states no licence, so its author keeps all rights: ask heyitsmeyo before reusing the design.