2 layers58 × 42.5 mm
Panelization
Hasatio/esp32DevKitS
The circuit taken as an example while designing the board Thing Plus C - ESP32 WROOM
179 parts
2 layers28.1 × 43.3 mm
Esp32DevKitS
Hasatio/esp32DevKitSThe circuit taken as an example while designing the board Thing Plus C - ESP32 WROOM
- Size
- 28.1 × 43.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 96
- Nets
- 91
- Pads
- 414
- Tracks, vias
- 2,220, 132
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 10 Mar 2023
- Updated
- 22 Jul 2024
Overview
Esp32DevKitS is an open-source printed circuit board by Hasatio, from the Hasatio/esp32DevKitS repository on GitHub. It is a 2-layer board of 28.1 × 43.3 mm with 96 parts on 91 nets, routed with 2,220 tracks and 132 vias.
It is built around the ADS1115IDGS, CH340K and ADXL345-EP, with the MCP73831 and MBT3904DW1T1 among its other parts. Its parts include 31 resistors, 14 capacitors, 11 ICs, 7 connectors and 4 diodes. It belongs with the ESP32 boards of this library.
Main components
5
ADS1115IDGS
MSOP10Ultra-Small, Low-Power, 4 Channels 16-Bit Analog-to-Digital Converter with Internal ReferenceTexas InstrumentsUncategorised
CH340K
ESSOP-10-150mil-1mm-20℃~+70℃ 2Mbps 3.3V、5V USB 2.0 USB to serial ESSOP-10-150mil-1mm USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB Converters
ADXL345-EP
LGA-14(3x5x0.8)LGA-14(3x5x0.8) New Arrivals ROHSAnalog DevicesUncategorised
MCP73831
UncategorisedMicrochip Technology
MBT3904DW1T1
SOT-363-6-55℃~+150℃ 100 150mW 200mA 300MHz 300mV 40V NPN SOT-363-6 Bipolar (BJT)onsemiBipolar (BJT)
README
README.mdESP32-DEVKIT-S
The circuit taken as an example while designing the board Thing Plus C - ESP32 WROOM
This pcb scaled down using the components in the example schematic
Revision 0
Added:
- 1x ADXL345 (Accelerometer)
- 2x 1x20 FPC connector for ESP pins
- In breakable PCB:
- 4x ADS1115 (Analog to Digital Converter)
- 1x20 FPC connector
- 1x QWIIC connector
Changed:
- ESP32-WROOM-32D model
- Battery socket breakable PCB
- Logo
Removed:
- RGB led
- SD card
Note: The connection cannot be made because the tx rx connection paths are not correct.
Revision 1
- Two circuits were produced for the left and right foot.
Added:
- New circuit in mirror image design
Changed:
- Circuit design, components in usb communication and components in the power section
- CH340C model
- TX, RX connection paths reversed
- Analog pull up resistor 100k
Note: The battery does not charge when the switch is in the off position.
Revision 2
Changed:
- The on/off switch will only be used for battery discharge
Parts
96| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 150k | SparkFun ESP32 Thing Plus C:0402-TIGHT | R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R20, R21, R22, R23, R24, R25 |
| 8 | 1.0uF | SparkFun ESP32 Thing Plus C:0402-TIGHT | C1, C2, C3, C8, C9, C10, C11, C14 |
| 6 | 10k | SparkFun ESP32 Thing Plus C:0402-TIGHT | R1, R3, R4, R7, R8, R26 |
| 5 | , , , , | ||
| 4 | >VALUE | Silicon-Standard:QFN-10-RSE | >NAME, >NAME, >NAME, >NAME |
| 4 | ADS1115IDGS | Package_SO:TSSOP-10_3x3mm_P0.5mm | U5, U6, U7, U8 |
| 3 | 1k | SparkFun ESP32 Thing Plus C:0402-TIGHT | R9, R27, R34 |
| 3 | 4k7 | SparkFun ESP32 Thing Plus C:0402-TIGHT | R2, R5, R6 |
| 3 | Conn_01x20 | Connector_FFC-FPC:Molex_200528-0200_1x20-1MP_P1.00mm_Horizontal | J3, J5, J6 |
| 3 | LOGO | logo:Hasatio_logo_mini | G***, G***, G*** |
| 2 | SparkFun ESP32 Thing Plus C:SOT23-5 | U2, U10 | |
| 2 | 0.1uF | SparkFun ESP32 Thing Plus C:0402-TIGHT | C12, C13 |
| 2 | 10uF | SparkFun ESP32 Thing Plus C:0402-TIGHT | C4, C5 |
| 2 | 4.7uF | SparkFun ESP32 Thing Plus C:0402-TIGHT | C6, C7 |
| 2 | 5.1k | SparkFun ESP32 Thing Plus C:0402-TIGHT | R32, R33 |
| 2 | >VALUE | Switches:TACTILE_SWITCH_SMD_2.8X1.9MM | >NAME, >NAME |
| 2 | JUMPER-SMT_2_NC_TRACE_SILK | SparkFun ESP32 Thing Plus C:SMT-JUMPER_2_NC_TRACE_SILK | JP1, JP2 |
| 2 | QWIIC_RIGHT_ANGLE | SparkFun ESP32 Thing Plus C:JST04_1MM_RA | J4, J7 |
| 2 | VAL** | Panelization:mouse-bite-1mm x4 | mouse-bite-1mm-slot, mouse-bite-1mm-slot |
| 1 | 2.0k | SparkFun ESP32 Thing Plus C:0402-TIGHT | R28 |
| 1 | >VALUE | SparkFun ESP32 Thing Plus C:ESP-WROOM-32-NARROW | U3 |
| 1 | ADXL345 | Package_LGA:LGA-14_3x5mm_P0.8mm_LayoutBorder1x6y | U1 |
| 1 | BLUE | SparkFun ESP32 Thing Plus C:LED-0603 | D5 |
| 1 | Boot | SparkFun ESP32 Thing Plus C:TACTILE_SWITCH_SMD_4.6X2.8MM | S1 |
| 1 | CH340K | Package_SO:SSOP-10_3.9x4.9mm_P1.00mm | U9 |
| 1 | DMG2305UX 20V/4.2A/52mΩ/1.4W | SparkFun ESP32 Thing Plus C:SOT23-3 | Q1 |
| 1 | FRAME-LEDGER | SparkFun ESP32 Thing Plus C:CREATIVE_COMMONS | FRAME1 |
| 1 | JST_2MM_MALE | SparkFun ESP32 Thing Plus C:JST-2-SMD | J1 |
| 1 | LOGO | logo:Hasatio_logo_micro | G*** |
| 1 | LOGO | logo:qr-esp32-devkit-s | G*** |
| 1 | MAX17048 | SparkFun ESP32 Thing Plus C:DFN-8 | U11 |
| 1 | MBT3904DW1T1 | SparkFun ESP32 Thing Plus C:SC70-6 | Q2 |
| 1 | MCP73831 | SparkFun ESP32 Thing Plus C:SOT23-5 | U4 |
| 1 | RED | SparkFun ESP32 Thing Plus C:LED-0603 | D2 |
| 1 | Reset | SparkFun ESP32 Thing Plus C:TACTILE_SWITCH_SMD_4.6X2.8MM | S2 |
| 1 | S4 3A/10V/280mV | SparkFun ESP32 Thing Plus C:SOD-323 | D1 |
| 1 | USB_C_2-LAYER_PADS | SparkFun ESP32 Thing Plus C:USB-C-16P-2LAYER-PADS | J2 |
| 1 | VAL** | Panelization:mouse-bite-1mm 2 | mouse-bite-emm-slot |
| 1 | VAL** | Panelization:mouse-bite-1mm 4 | mouse-bite-1mm-slot |
| 1 | VAL** | Panelization:mouse-bite-1mm x2 | mouse-bite-1mm-slot |
| 1 | Yellow | SparkFun ESP32 Thing Plus C:LED-0603 | D3 |
The 95 most common of 96 parts.
Questions
How big is the Esp32DevKitS PCB?
It measures 28.1 × 43.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Esp32DevKitS use?
96 parts, built around the ADS1115IDGS, CH340K, ADXL345-EP and MCP73831. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Esp32DevKitS KiCad files?
From the Hasatio/esp32DevKitS repository on GitHub, at the commit this page was made from: the board is Rev0/Rev0.kicad_pcb and its schematic Rev0/ESP32-DEVKIT-S-cp2102.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Esp32DevKitS design in my own project?
Its repository states no licence, so its author keeps all rights: ask Hasatio before reusing the design.
More from Hasatio/esp32DevKitS
3- 2 layers28.1 × 43.3 mm
ESP32-DEVKIT S cp2102
Hasatio/esp32DevKitS
The circuit taken as an example while designing the board Thing Plus C - ESP32 WROOM
92 parts - 2 layers28.9 × 42.5 mm
Esp32DevKitS
Hasatio/esp32DevKitS
The circuit taken as an example while designing the board Thing Plus C - ESP32 WROOM
91 parts
Similar boards
- 2 layers25.4 × 58.9 mm
Esp32-thing
vanessaPrankl/HeadMouse
This project provides hardware, enclosure and software for the head-motion based computermouse HeadMouse.
72 parts2 - 2 layers22.9 × 59.7 mm
Version current
oomlout/oomlout_oomp_documentation_bot
a bot that goes around generating rough documentation for kicad projects
110 parts - 6 layers64.8 × 69.9 mm
- 2 layers86.4 × 54.6 mm
- 2 layers80 × 42.5 mm
Bebl v2
wyolum/bebl_v2
"Bar End Brake Light" , redux. v2 of Justin's original BEBL with mods.
75 parts1 - 2 layers52.8 × 71.8 mm
ESPBoosted
schoolllex/ESPBoosted
A custom, feature-rich ESP32-WROOM-32 development board featuring built-in environmental sensors, power management, and expansion interfaces.
51 parts - 4 layers42 × 42 mm
- 2 layers97 × 77.5 mm
ESPlant
CCHS-Melbourne/ESPlant
Environmental Sensor Plant - solar WiFi gardening/meteorological sensor using ESP8266
77 parts37