2 layers28.1 × 43.3 mm
Esp32DevKitS
Hasatio/esp32DevKitS
The circuit taken as an example while designing the board Thing Plus C - ESP32 WROOM
96 parts
2 layers58 × 42.5 mm
Panelization
Hasatio/esp32DevKitSThe circuit taken as an example while designing the board Thing Plus C - ESP32 WROOM
- Size
- 58 × 42.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 179
- Nets
- 194
- Pads
- 815
- Tracks, vias
- 6,623, 408
- Pours
- 14
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 10 Mar 2023
- Updated
- 22 Jul 2024
Overview
Panelization is an open-source printed circuit board by Hasatio, from the Hasatio/esp32DevKitS repository on GitHub. It is a 2-layer board of 58 × 42.5 mm with 179 parts on 194 nets, routed with 6,623 tracks and 408 vias.
It is built around the CH340C, ADS1115IDGS and ADXL345-EP, with the MCP73831 and MBT3904DW1T1 among its other parts. Its parts include 62 resistors, 28 capacitors, 20 ICs, 14 connectors and 8 diodes.
Main components
5
CH340C
SOP-16-20℃~+70℃ 2Mbps 3.3V、5V 50uA 7mA Transceiver USB 2.0 SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB Converters
ADS1115IDGS
MSOP10Ultra-Small, Low-Power, 4 Channels 16-Bit Analog-to-Digital Converter with Internal ReferenceTexas InstrumentsUncategorised
ADXL345-EP
LGA-14(3x5x0.8)LGA-14(3x5x0.8) New Arrivals ROHSAnalog DevicesUncategorised
MCP73831
UncategorisedMicrochip Technology
MBT3904DW1T1
SOT-363-6-55℃~+150℃ 100 150mW 200mA 300MHz 300mV 40V NPN SOT-363-6 Bipolar (BJT)onsemiBipolar (BJT)
README
README.mdESP32-DEVKIT-S
The circuit taken as an example while designing the board Thing Plus C - ESP32 WROOM
This pcb scaled down using the components in the example schematic
Revision 0
Added:
- 1x ADXL345 (Accelerometer)
- 2x 1x20 FPC connector for ESP pins
- In breakable PCB:
- 4x ADS1115 (Analog to Digital Converter)
- 1x20 FPC connector
- 1x QWIIC connector
Changed:
- ESP32-WROOM-32D model
- Battery socket breakable PCB
- Logo
Removed:
- RGB led
- SD card
Note: The connection cannot be made because the tx rx connection paths are not correct.
Revision 1
- Two circuits were produced for the left and right foot.
Added:
- New circuit in mirror image design
Changed:
- Circuit design, components in usb communication and components in the power section
- CH340C model
- TX, RX connection paths reversed
- Analog pull up resistor 100k
Note: The battery does not charge when the switch is in the off position.
Revision 2
Changed:
- The on/off switch will only be used for battery discharge
Parts
179| Qty | Value | Footprint | References |
|---|---|---|---|
| 32 | 150k | SparkFun ESP32 Thing Plus C:0402-TIGHT | R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R20, R21, R22, R23, R24, R25 +16 |
| 16 | 1.0uF | SparkFun ESP32 Thing Plus C:0402-TIGHT | C1, C2, C3, C8, C9, C10, C11, C13, C15, C16, C17, C22, C23, C24, C25, C27 |
| 12 | 10k | SparkFun ESP32 Thing Plus C:0402-TIGHT | R1, R3, R4, R7, R8, R26, R32, R34, R35, R38, R39, R57 |
| 8 | >VALUE | Silicon-Standard:QFN-10-RSE | >NAME, >NAME, >NAME, >NAME, >NAME, >NAME, >NAME, >NAME |
| 8 | ADS1115IDGS | Package_SO:TSSOP-10_3x3mm_P0.5mm | U5, U6, U7, U8, U15, U16, U17, U18 |
| 8 | VAL** | Panelization:mouse-bite-1mm 2 | mouse-bite-emm-slot, mouse-bite-emm-slot, mouse-bite-emm-slot, mouse-bite-emm-slot, mouse-bite-emm-slot, mouse-bite-emm-slot, mouse-bite-emm-slot, mouse-bite-emm-slot |
| 6 | 1k | SparkFun ESP32 Thing Plus C:0402-TIGHT | R9, R27, R31, R40, R58, R62 |
| 6 | 4k7 | SparkFun ESP32 Thing Plus C:0402-TIGHT | R2, R5, R6, R33, R36, R37 |
| 6 | Conn_01x20 | Connector_FFC-FPC:Molex_200528-0200_1x20-1MP_P1.00mm_Horizontal | J4, J5, J7, J11, J12, J14 |
| 6 | LOGO | logo:Hasatio_logo_mini | G***, G***, G***, G***, G***, G*** |
| 5 | , , , , | ||
| 4 | 0.1uF | SparkFun ESP32 Thing Plus C:0402-TIGHT | C12, C14, C26, C28 |
| 4 | 10uF | SparkFun ESP32 Thing Plus C:0402-TIGHT | C4, C5, C18, C19 |
| 4 | 4.7uF | SparkFun ESP32 Thing Plus C:0402-TIGHT | C6, C7, C20, C21 |
| 4 | 5.1k | SparkFun ESP32 Thing Plus C:0402-TIGHT | R29, R30, R60, R61 |
| 4 | JUMPER-SMT_2_NC_TRACE_SILK | SparkFun ESP32 Thing Plus C:SMT-JUMPER_2_NC_TRACE_SILK | JP1, JP2, JP3, JP4 |
| 4 | QWIIC_RIGHT_ANGLE | SparkFun ESP32 Thing Plus C:JST04_1MM_RA | J3, J6, J10, J13 |
| 2 | SparkFun ESP32 Thing Plus C:SOT23-5 | U2, U12 | |
| 2 | 2.0k | SparkFun ESP32 Thing Plus C:0402-TIGHT | R28, R59 |
| 2 | >VALUE | SparkFun ESP32 Thing Plus C:ESP-WROOM-32-NARROW | U3, U13 |
| 2 | ADXL345 | Package_LGA:LGA-14_3x5mm_P0.8mm_LayoutBorder1x6y | U1, U11 |
| 2 | BLUE | SparkFun ESP32 Thing Plus C:LED-0603 | D4, D8 |
| 2 | Boot | Switches:TACTILE_SWITCH_SMD_2.8X1.9MM | S1, S3 |
| 2 | CH340C | PCM_Package_SO_AKL:SOIC-16_3.9x9.9mm_P1.27mm | U9, U19 |
| 2 | DMG2305UX 20V/4.2A/52mΩ/1.4W | SparkFun ESP32 Thing Plus C:SOT23-3 | Q1, Q3 |
| 2 | JST_2MM_MALE | SparkFun ESP32 Thing Plus C:JST-2-SMD | J1, J8 |
| 2 | LOGO | logo:qr-esp32-devkit-s | G***, G*** |
| 2 | MAX17048 | SparkFun ESP32 Thing Plus C:DFN-8 | U10, U20 |
| 2 | MBT3904DW1T1 | SparkFun ESP32 Thing Plus C:SC70-6 | Q2, Q4 |
| 2 | MCP73831 | SparkFun ESP32 Thing Plus C:SOT23-5 | U4, U14 |
| 2 | ON/OFF | Button_Switch_SMD:SW_SPDT_k3-1295 | SW1, SW2 |
| 2 | RED | SparkFun ESP32 Thing Plus C:LED-0603 | D2, D6 |
| 2 | Reset | Switches:TACTILE_SWITCH_SMD_2.8X1.9MM | S2, S4 |
| 2 | S4 3A/10V/280mV | SparkFun ESP32 Thing Plus C:SOD-323 | D1, D5 |
| 2 | USB_C_2-LAYER_PADS | SparkFun ESP32 Thing Plus C:USB-C-16P-2LAYER-PADS | J2, J9 |
| 2 | VAL** | Panelization:mouse-bite-1mm x2 | mouse-bite-1mm-slot, mouse-bite-1mm-slot |
| 2 | Yellow | SparkFun ESP32 Thing Plus C:LED-0603 | D3, D7 |
The 177 most common of 179 parts.
Questions
How big is the Panelization PCB?
It measures 58 × 42.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Panelization use?
179 parts, built around the CH340C, ADS1115IDGS, ADXL345-EP and MCP73831. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Panelization KiCad files?
From the Hasatio/esp32DevKitS repository on GitHub, at the commit this page was made from: the board is Rev2/panelization/panelization.kicad_pcb and its schematic Rev0/ESP32-DEVKIT-S-cp2102.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Panelization design in my own project?
Its repository states no licence, so its author keeps all rights: ask Hasatio before reusing the design.
More from Hasatio/esp32DevKitS
3- 2 layers28.1 × 43.3 mm
ESP32-DEVKIT S cp2102
Hasatio/esp32DevKitS
The circuit taken as an example while designing the board Thing Plus C - ESP32 WROOM
92 parts - 2 layers28.9 × 42.5 mm
Esp32DevKitS
Hasatio/esp32DevKitS
The circuit taken as an example while designing the board Thing Plus C - ESP32 WROOM
91 parts
Similar boards
- 2 layers22.9 × 59.7 mm
Version current
oomlout/oomlout_oomp_documentation_bot
a bot that goes around generating rough documentation for kicad projects
110 parts - 2 layers25.4 × 58.9 mm
Esp32-thing
vanessaPrankl/HeadMouse
This project provides hardware, enclosure and software for the head-motion based computermouse HeadMouse.
72 parts2 - 4 layers25.4 × 50.8 mm
- 6 layers64.8 × 69.9 mm
- 2 layers80 × 42.5 mm
Bebl v2
wyolum/bebl_v2
"Bar End Brake Light" , redux. v2 of Justin's original BEBL with mods.
75 parts1 - 2 layers112 × 79 mm
- 4 layers89 × 58 mm
HALMET
hatlabs/HALMET-hardware
Hat Labs Marine Engine & Tank interface hardware design files
227 parts8CC-BY-4.0 - 2 layers96.2 × 53.4 mm
Fancontroller
dj-bauer/espfancooling
Just another fan controller, but this time with bluetooth
89 parts2GPL-3.0