

Stm32g431 devboard
KiCad design files for an STM32G431 development board
- Size
- 60 × 22 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 42
- Nets
- 63
- Pads
- 207
- Tracks, vias
- 539, 65
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 17 May 2026
- Updated
- 25 May 2026
Overview
Stm32g431 devboard is an open-source printed circuit board by guillegil, from the guillegil/STM32G431-Development-Board repository on GitHub, published under the MIT licence. It is a 4-layer board of 60 × 22 mm with 42 parts on 63 nets, routed with 539 tracks and 65 vias.
It is built around the LM66100DCK, TPS7A0533PDBV and 1N4148W. Its parts include 12 capacitors, 10 resistors, 5 connectors, 4 ICs and 4 diodes. It belongs with the microcontroller boards boards and the STM32 boards of this library.
Main components
3LM66100DCK
SC-70-6-40℃~+125℃ 1 1.5A 1.5V~5.5V 150nA 95mΩ Integrated FET Reverse current blocking、Reverse polarity protection、With enable SC-70-6 ORing Controllers ROHSTexas InstrumentsPower Distribution SwitchesTPS7A0533PDBV
SOT-23-5-40℃~+125℃@(Tj) 1 180uVrms 1uA 200mA 235mV@(200mA) 3.3V 40dB@(1MHz) 5.5V Fixed Over Current Protection、Over Temperature Protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators1N4148W
SOD-123150mA 1A 1V@50mA 1uA@75V 400mW 4ns 75V Independent SOD-123 Switching Diodes ROHSSTMicroelectronicsSwitching Diodes
README
README.mdSTM32G431 Development Board
KiCad 10 design files for a small development board based on the STMicroelectronics STM32G431CBT6 microcontroller (Cortex-M4F, 170 MHz, 128 KB flash, USB).
This is a personal learning project — my first custom-designed PCB, built as preparation for a more complex nRF5340-based wireless keyboard development board.
Features
- STM32G431CBT6 in LQFP-48 package (hand-solderable)
- USB-C connector for power and native USB device communication
- 3.3 V LDO regulator
- SWD programming header
- UART debug header
- User LED + user button
- Reset button + boot-mode jumper
- GPIO breakout headers for experimentation
Project goals
- Learn KiCad 10 schematic and PCB design workflow
- Learn home reflow soldering (hot plate + hot air)
- Build a base for future Zephyr RTOS experimentation
- Prepare skills for a larger custom-keyboard project
Status
🟡 In design — schematic in progress
Tools used
- KiCad 10.x
- Zephyr RTOS / nRF Connect SDK (firmware, future)
- JLCPCB (PCB fabrication, planned)
License
See LICENSE. This project is open source under the MIT License.
Parts
42| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C4, C8, C9, C10, C11 |
| 4 | 1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C3, C5, C7 |
| 3 | 0 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5, R7, R8 |
| 2 | 18pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C_LSE1, C_LSE2 |
| 2 | 5k1 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
| 2 | LM66100DCK | Package_TO_SOT_SMD:SOT-363_SC-70-6 | U1, U3 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R9 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C6 |
| 1 | 1N4148W | Diode_SMD:D_SOD-323 | D5 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R10 |
| 1 | 1k5 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
| 1 | 32.768 kHz | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | 4.7uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C12 |
| 1 | 470 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6 |
| 1 | 680 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4 |
| 1 | BOOT | Button_Switch_SMD:SW_SPST_PTS810 | SW2 |
| 1 | BTN_RST | Button_Switch_SMD:SW_SPST_PTS810 | SW1 |
| 1 | Conn_02x06 | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical_SMD | J6 |
| 1 | FerriteBead | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | FB1 |
| 1 | GREEN | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2 |
| 1 | J_L | Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_Vertical | J3 |
| 1 | J_R | Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_Vertical | J4 |
| 1 | J_VBAT | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | LD1 | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D3 |
| 1 | RED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | STM32G431CBTx | Package_QFP:LQFP-48_7x7mm_P0.5mm | MCU1 |
| 1 | TPS7A0533PDBV | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U4 |
| 1 | USB_C_Receptacle_USB2.0_16P | stm32g431_devboard:USB_C_Receptacle_GCT_USB4085 | J2 |
| 1 | USB_ESD | Package_TO_SOT_SMD:SOT-23-6 | U2 |
Similar boards
- 2 layers65 × 55 mm

- 2 layers115.2 × 78.6 mm

- 4 layers112 × 75 mm

- 2 layers85.6 × 54 mm

- 4 layers120 × 100 mm

Cryocooler
jhyland87/Cryocooler-Controller
Control system for STI Hybrid-98 Stirling cycle cryocooler.
338 parts2 - 6 layers46.5 × 47.2 mm

NAVCORE SoOP
kfilipekk/iridium_drone
STM32H743 flight controller that navigates without GPS from Iridium satellite Doppler
217 parts2MIT - 4 layers65 × 56 mm

Sensor HAT
Eniemooo/Sensor-HAT
Open-hardware indoor air sensor (CO2, VOC/NOx, T/RH, light, sound): HAT for Raspberry Pi or standalone with Seeed XIAO + ESPHome. KiCad 10.
112 parts - 2 layers40 × 40 mm

Questions
How big is the Stm32g431 devboard PCB?
It measures 60 × 22 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Stm32g431 devboard use?
42 parts, built around the LM66100DCK, TPS7A0533PDBV and 1N4148W. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Stm32g431 devboard KiCad files?
From the guillegil/STM32G431-Development-Board repository on GitHub, at the commit this page was made from: the board is stm32g431_devboard.kicad_pcb and its schematic gpio_breakout.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Stm32g431 devboard design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).