
Beaglebone obd
KoffeinFlummi/rustbucket
Access your car's diagnostics with a BeagleBone Blue and Rust.

Kicad project for led dimmer board
Led dimmer boat is an open-source printed circuit board by gpgreen, from the gpgreen/led-dimmer-boat repository on GitHub. It is a 2-layer board of 62 × 30 mm with 19 parts on 15 nets, routed with 133 tracks and 13 vias.
It is built around the IRLB8721PBF and M2023SS1W03/U. Its parts include 3 capacitors, 3 resistors, 3 transistors, 3 connectors and 2 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
KiCad design for a LED strip dimmer. Provides power and switch on/off for the board. The dimmer controls are on-off-on switch and a rheostat. If the switch is thrown one way, we get a dimmable white light, and if thrown the other way, we get a dimmable red light from the LED strip.
The firmware project:
PCB

| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 0.1uF | Capacitors_SMD:C_0603_HandSoldering | C2, C3 |
| 2 | IRLB8721PBF | TO_SOT_Packages_THT:TO-220-3_Horizontal | Q1, Q2 |
| 2 | MountingHole | Mounting_Holes:MountingHole_3.2mm_M3 | H1, H2 |
| 1 | 0.22uF | Capacitors_SMD:C_0603_HandSoldering | C1 |
| 1 | 10K | Resistors_SMD:R_0603_HandSoldering | R3 |
| 1 | 1N5400 | Diodes_SMD:D_SOD-323_HandSoldering | D1 |
| 1 | 2N3904 | TO_SOT_Packages_THT:TO-92_Inline_Wide | Q4 |
| 1 | 300K | Resistors_SMD:R_0603_HandSoldering | R2 |
| 1 | 82K | Resistors_SMD:R_0603_HandSoldering | R1 |
| 1 | ATtiny13A-PU-ND | Housings_DIP:DIP-8_W7.62mm | U1 |
| 1 | LEDSTRIP | Connectors_JST:JST_EH_B04B-EH-A_04x2.50mm_Straight | J3 |
| 1 | LM7805S/NOPB | TO_SOT_Packages_SMD:TO-263-3_TabPin2 | U2 |
| 1 | M2023SS1W03 | CustomComponents:SW_DPDT_NKK_PC_MOUNT | SW1 |
| 1 | PWR | Connectors_JST:JST_EH_B02B-EH-A_02x2.50mm_Straight | J1 |
| 1 | Prog | Pin_Headers:Pin_Header_Straight_2x03_Pitch2.54mm | J2 |
| 1 | R_POT | Pin_Headers:Pin_Header_Straight_1x03_Pitch2.54mm | RV1 |

KoffeinFlummi/rustbucket
Access your car's diagnostics with a BeagleBone Blue and Rust.


stelioskat/esp8266-led-dimmer
Wifi enabled LED strip dimmer that is controlled using MQTT messages.



chl33/Dough133
A temperature-controlled container for proofing and fermenting soughdough


Adamibus/ESPAtomizer-iOS
This is a minimal KiCad 6/7 project skeleton. Open ESPAtomizer.kicadpro in KiCad.
It measures 62 × 30 mm and has 2 copper layers, 1.6 mm thick.
19 parts, built around the IRLB8721PBF and M2023SS1W03/U. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the gpgreen/led-dimmer-boat repository on GitHub, at the commit this page was made from: the board is led-dimmer-boat.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask gpgreen before reusing the design.