

Glasgow
Scots Army Knife for electronics
- Size
- 80 × 49 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 118
- Nets
- 110
- Pads
- 528
- Tracks, vias
- 1,151, 160
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 21 Jan 2018
- Updated
- 6 Nov 2026
Overview
Glasgow is an open-source printed circuit board by GlasgowEmbedded, from the GlasgowEmbedded/glasgow repository on GitHub, published under the 0BSD licence. It is a 4-layer board of 80 × 49 mm with 118 parts on 110 nets, routed with 1,151 tracks and 160 vias.
It is built around the CY7C68013A-56LTXC, ICE40UP5K-SG48ITR50 and ADC081C021CIMM, with the DAC081C081CIMK, FXMA108BQX and TPS73101DBV among its other parts. Its parts include 46 capacitors, 30 resistors, 14 ICs, 5 diodes and 4 connectors. It belongs with the fPGA and programmable logic and interfaces and adapters boards and the FPGA and CPLD boards of this library.
Main components
8CY7C68013A-56LTXC
QFN-56-EP(8x8)0℃~+70℃ 16KB 16KB 24 3V~3.6V 48MHz 51 Series 8 Bit External ROMless QFN-56-EP(8x8) Microcontrollers (MCU/MPU/SOC)Infineon TechnologiesMicrocontrollers (MCU/MPU/SOC)ICE40UP5K-SG48ITR50
QFN-48QFN-48 Programmable Logic Device (CPLDs/FPGAs) ROHSLatticeProgrammable Logic Device (CPLDs/FPGAs)ADC081C021CIMM
VSSOP-8-0.65mm-40℃~+105℃ 0.2LSB 1 100nA 188.9kHz 2.7V~5.5V 49.8dB 8 Built-in I2C No SAR VSSOP-8-0.65mm Analog to Digital Converters (ADC) ROHSTexas InstrumentsAnalog To Digital Converters (ADCs)DAC081C081CIMK
TSOT-23-6-40℃~+125℃ 0.6LSB 1 130nA 2.7V~5.5V 4.5us 8 I2C Power-on reset、Power-down mode、Multi-chip synchronization Voltage Buffer TSOT-23-6 Digital to Analog Converters (DAC) ROHSTexas InstrumentsDigital To Analog Converters (DAC)FXMA108BQX
DQFN-20-EP(2.5x4.5)-40℃~+85℃ 1 1.65V~5.5V 1.65V~5.5V 100Mbps 8 Auto Direction Detection、Power-Off Protection Bidirectional Tri-State DQFN-20-EP(2.5x4.5) Translators, Level Shifters ROHSonsemiTranslators, Level ShiftersTPS73101DBV
SOT-23-5-40℃~+125℃@(Tj) 1 1.2V~5.5V 100mV@(150mA) 150mA 30uVrms 37dB@(10kHz)、58dB@(100Hz) 400uA 5.5V Adjustable Over Current Protection、Over Temperature Protection、Over Voltage Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLM3880MF-1AF
SOT-23-6-40℃~+125℃ 2.7V~5.5V 3 80uA Open-drain Voltage monitor SOT-23-6 Supervisor and Reset ICs ROHSTexas InstrumentsSupervisor And Reset ICsMIC5355-S4YMME
MSOP-8-EP-40℃~+125℃@(Tj) 1.2V、3.3V 146uVrms 2 350mV@(500mA) 5.5V 500mA 60dB@(1kHz) 70uA Fixed Over Current Protection、Enable、Thermal Shutdown Positive MSOP-8-EP Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMicrochip TechnologyVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdGlasgow Interface Explorer
For all information regarding this project, please refer to our documentation manual.
Parts
118| Qty | Value | Footprint | References |
|---|---|---|---|
| 28 | u1 | Capacitor_SMD:C_0603_1608Metric_Pad0.99x1.00mm_HandSolder | C2, C3, C10, C13, C15, C17, C20, C21, C22, C23, C24, C25, C30, C32, C33, C35 +12 |
| 14 | 4u7 | Capacitor_SMD:C_0603_1608Metric_Pad0.99x1.00mm_HandSolder | C1, C14, C16, C18, C19, C26, C27, C28, C29, C31, C34, C39, C41, C46 |
| 9 | 100k | Resistor_SMD:R_0603_1608Metric_Pad0.99x1.00mm_HandSolder | R4, R6, R7, R8, R9, R11, R17, R18, R19 |
| 4 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.99x1.00mm_HandSolder | R20, R21, R25, R26 |
| 4 | Fiducial_0.75mm_Dia_1.5mm_Outer | Glasgow:Fiducial_0.75mm_Dia_1.5mm_Outer | FID1, FID1, FID2, FID4 |
| 4 | Mounting_Hole_PAD | MountingHole:MountingHole_3.2mm_M3_Pad | MK1, MK2, MK3, MK4 |
| 3 | 2k2 | Resistor_SMD:R_0603_1608Metric_Pad0.99x1.00mm_HandSolder | R1, R2, R10 |
| 3 | 680 | Resistor_SMD:R_0603_1608Metric_Pad0.99x1.00mm_HandSolder | R12, R13, R14 |
| 3 | GRN | LED_SMD:LED_0603_1608Metric_Pad0.82x1.00mm_HandSolder | D1, D2, D3 |
| 2 | 12n | Capacitor_SMD:C_0603_1608Metric_Pad0.99x1.00mm_HandSolder | C37, C44 |
| 2 | 18p | Capacitor_SMD:C_0603_1608Metric_Pad0.99x1.00mm_HandSolder | C11, C12 |
| 2 | 24k3 | Resistor_SMD:R_0603_1608Metric_Pad0.99x1.00mm_HandSolder | R24, R29 |
| 2 | 49k9 | Resistor_SMD:R_0603_1608Metric_Pad0.99x1.00mm_HandSolder | R22, R27 |
| 2 | 59k | Resistor_SMD:R_0603_1608Metric_Pad0.99x1.00mm_HandSolder | R23, R28 |
| 2 | ADC081C021CIMM | Package_SO:MSOP-8_3x3mm_P0.65mm | U9, U12 |
| 2 | Conn_02x10_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x10_P2.54mm_Vertical | J2, J3 |
| 2 | DAC081C081CIMK | Package_TO_SOT_SMD:SOT-23-6 | U10, U13 |
| 2 | FXMA108BQX | Package_DFN_QFN:WQFN-20-1EP_2.5x4.5mm_P0.5mm_EP1x2.9mm | U5, U6 |
| 2 | Mounting_Hole | MountingHole:MountingHole_2.5mm | MK5, MK6 |
| 2 | TPS73101DBV | Package_TO_SOT_SMD:SOT-23-5 | U11, U14 |
| 1 | 100 | Resistor_SMD:R_0603_1608Metric_Pad0.99x1.00mm_HandSolder | R30 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric_Pad0.99x1.00mm_HandSolder | R3 |
| 1 | 1V2 | TestPoint:TestPoint_Pad_D1.0mm | TP2 |
| 1 | 220k | Resistor_SMD:R_0603_1608Metric_Pad0.99x1.00mm_HandSolder | R5 |
| 1 | 24M | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSoldering | Y1 |
| 1 | 390 | Resistor_SMD:R_0603_1608Metric_Pad0.99x1.00mm_HandSolder | R15 |
| 1 | 3V3 | TestPoint:TestPoint_Pad_D1.0mm | TP3 |
| 1 | 500m | Fuse:Fuse_0603_1608Metric_Pad0.99x1.00mm_HandSolder | F1 |
| 1 | 5V | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | 604 | Resistor_SMD:R_0603_1608Metric_Pad0.99x1.00mm_HandSolder | R16 |
| 1 | CAT24C256W | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | CAT24M01W | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | CLKREF | TestPoint:TestPoint_Pad_D1.0mm | TP6 |
| 1 | CY7C68013A-56LTX | Glasgow:QFN-56-1EP_8x8mm_P0.5mm_EP6.1x6.1mm_ThermalVias | U1 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Horizontal | J4 |
| 1 | ICE40UP5K-SG48ITR | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm | U4 |
| 1 | LM3880MF-1AF | Package_TO_SOT_SMD:SOT-23-6 | U7 |
| 1 | MIC5355-S4YMME | Glasgow:MSOP-8-1EP_3x3mm_P0.65mm_EP2.54x2.8mm_ThermalVias | U8 |
| 1 | RED | LED_SMD:LED_0603_1608Metric_Pad0.82x1.00mm_HandSolder | D5 |
| 1 | SCL | TestPoint:TestPoint_Pad_D1.0mm | TP5 |
| 1 | SDA | TestPoint:TestPoint_Pad_D1.0mm | TP4 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Molex_47346-0001 | J1 |
| 1 | YEL | LED_SMD:LED_0603_1608Metric_Pad0.82x1.00mm_HandSolder | D4 |
The 117 most common of 118 parts.
More from GlasgowEmbedded/glasgow
2- 6 layers95 × 55 mm

- 6 layers95 × 55 mm

Similar boards
- 4 layers80 × 49 mm

- 6 layers80 × 49 mm

ButterStick
butterstick-fpga/butterstick-hardware
Basic ECP5 based GigE to SYZYGY interface.
256 parts225 - 2 layers17.8 × 43.2 mm

Leech
Disasm/leech-pcb
An extension board with iCE40UP5k for the STM32F411 "Black Pill" board.
15 parts1 - 6 layers83.3 × 61.3 mm

- 2 layers102 × 62 mm

- 4 layers45 × 75 mm

- 4 layers17.8 × 50.8 mm

- 4 layers67 × 157 mm

Questions
How big is the Glasgow PCB?
It measures 80 × 49 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Glasgow use?
118 parts, built around the CY7C68013A-56LTXC, ICE40UP5K-SG48ITR50, ADC081C021CIMM and DAC081C081CIMK. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Glasgow KiCad files?
From the GlasgowEmbedded/glasgow repository on GitHub, at the commit this page was made from: the board is hardware/boards/glasgow/revA/glasgow.kicad_pcb and its schematic hardware/boards/glasgow/revC3/glasgow.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Glasgow design in my own project?
Its repository publishes it under the 0BSD licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).