Skip to the content
2 layersWiggle spine, the printed circuit board in 3D

Modular I/O for multi-channel sound, light, and motion

Copper layers
2
Thickness
1.6 mm
Parts
173
Nets
195
Pads
821
Tracks, vias
0, 0
Routed
Not yet
KiCad
KiCad 4
Created
30 Nov 2015
Updated
30 Nov 2015

Overview

Wiggle spine is an open-source printed circuit board by gitter-badger, from the gitter-badger/wiggleport repository on GitHub, published under the MIT licence. It is a 2-layer board with 173 parts on 195 nets.

It is built around the SIP32408EVB, SN75176BD and PLR135/T8, with the RT8299AZQW, NC7WZ14P6 and FT2232HL among its other parts. Its parts include 83 capacitors, 36 resistors, 15 ICs, 8 diodes and 7 connectors. It belongs with the audio and music boards and the FPGA and CPLD boards of this library.

Main components

10

README

README.md
wiggleport

Modular I/O for multi-channel sound, light, and motion

  • Use it to create objects and environments that are perfectly synchronized with immersive sound and vibration
  • Drive up to 14 speakers at 48/96 kHz per channel from one USB port
  • Connect sensors and lights, sync them perfectly with sound and each other
  • Connect other audio-frequency devices like vibration transducers, LED strobes, and modular synthesizers
  • Use all the processing power in your PC, or run from an embedded Linux board like the Raspberry Pi 2
  • Accurate control of I/O timing from high-level Javascript code

Scale it up or down

  • Each "spine" board has a 480 Mbit/s USB 2.0 uplink and 7 connectors for modules:

    • wiggle out – 2x 25-watt class D speaker amplifiers
    • wiggle volts - 2x analog input and 2x analog output, DC-coupled with configurable gain
    • wiggle dig - 8x 5V differential GPIO (DMX512/RS422/RS485/SPI/switch/piezo) and 1x I²C (in addition to the 1x differential and 1x I²C on the spine)
    • wiggle bright - 1x addressable LED drive (SPI/WS2811). Consists of RJ45 cable driver and receiver boards, so the signal can travel. Typically drives ~1000 LEDs at 100fps.
  • Multiple spines can be synchronized with cheap twisted-pair cable

    • USB links can go to the same or different computers, depending on how much processing power you need
    • Everyone shares a common audio clock and timestamps

Internals

Wiggleport is an open source hardware design optimized for simple and straightforward real-time performance. It's based around an FTDI FT2232H high-speed USB FIFO interface, combined with a precision clock synthesizer and a tiny FPGA for glue logic. It stays simple and inexpensive by doing much of the work in software, relying on the powerful CPUs available on even small embedded Linux boards now.

Wiggleport isn't really a sound card, and it doesn't appear as a sound card to your OS. Instead, it has its own APIs for C++, MIDI, and Javascript. You can write code for precisely timed multichannel sound installations on your laptop on Mac OS, for example, and run the same code on a Raspberry Pi later on.

Coming soon... development is happening here now.

Parts

173
QtyValueFootprintReferences
480.1uFCapacitors_SMD:C_0805C2, C3, C11, C14, C18, C19, C21, C24, C25, C26, C28, C30, C31, C32, C33, C34 +32
1710uF Capacitors_SMD:C_1206C10, C13, C15, C17, C20, C27, C35, C48, C49, C53, C54, C55, C56, C60, C61, C70 +1
101uF Capacitors_SMD:C_0805C50, C57, C62, C66, C67, C73, C75, C77, C80, C83
910kResistors_SMD:R_0805R1, R2, R3, R5, R16, R17, R18, R19, R36
7100kResistors_SMD:R_0805R20, R24, R25, R29, R30, R31, R33
72.54mm 2x10 right angle female headerSocket_Strips:Socket_Strip_Angled_2x10MOD1, MOD2, MOD3, MOD4, MOD5, MOD6, MOD7
7Ferrite beadResistors_SMD:R_0805FB1, FB2, FB3, FB4, FB5, FB6, FB7
4150Resistors_SMD:R_0805R13, R15, R21, R26
42.2kResistors_SMD:R_0805R6, R32, R34, R35
44.7kResistors_SMD:R_0805R4, R7, R11, R12
4BAT54 2x common cathodeTO_SOT_Packages_SMD:SOT-23D2, D3, D5, D6
38.5VWMTO_SOT_Packages_SMD:SOT-23D4, D7, D8
3IRFML8244TO_SOT_Packages_SMD:SOT-23Q1, Q2, Q3
3NC7WZ14TO_SOT_Packages_SMD:SC-70-6U3, U4, U5
3SiP32408TDFN4:TDFN4U10, U11, U12
210Resistors_SMD:R_0805R8, R9
2100pFCapacitors_SMD:C_0805C52, C59
21nFCapacitors_SMD:C_0805C22, C23
220pFCapacitors_SMD:C_0805C12, C16
222uHInductors_NEOSID:Neosid_Inductor_SM-NE127L1, L2
25.1k 1%Resistors_SMD:R_0805R23, R28
2RT8299AHousings_SOIC:SOIC-8-1EP_3.9x4.9mm_Pitch1.27mmU8, U9
10.1uFTO_SOT_Packages_SMD:SOT-886C1
110/100baseT transformerHousings_SOIC:SOIC-16_7.5x10.3mm_Pitch1.27mmT1
112 MHzCrystals:Crystal_HC49-SD_SMDX2
112k 1%Resistors_SMD:R_0805R10
116k 1%Resistors_SMD:R_0805R27
11MResistors_SMD:R_0805R14
11nFCapacitors_ThroughHole:C_Rect_L13_W4_P10C29
125.0000 MHz 15ppm 8pFCrystals:crystal_FA238-TSX3225X1
127k 1%Resistors_SMD:R_0805R22
12A PTCResistors_SMD:R_1812F1
15-24V 16ATerminal_Blocks:TerminalBlock_Pheonix_PT-3.5mm_4polCON2
15-24V 5AConnect:BARREL_JACKCON1
193C56Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mmU1
1AOD4189TO_SOT_Packages_SMD:TO-252-2LeadQ4
1FT2232HHousings_QFP:LQFP-64_10x10mm_Pitch0.5mmU2
1PLR135TOSLINK:Everlight-PLR135-T8CON3
1PLT133TOSLINK:Everlight-PLT133-T6ACON4
1SN75176BHousings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mmU6
1Si5351BHousings_DFN_QFN:QFN-20-1EP_4x4mm_Pitch0.5mmU15
1TCR2EF12TO_SOT_Packages_SMD:SOT-353U14
1TCR2EF25TO_SOT_Packages_SMD:SOT-353U13
1TVS DIODE 5.5VWMSOT363:SOT363D1
1USB-AConnect:USB_A_VerticalCON7
1USB-BConnect:USB_BCON5
1XLR-3 FemaleConnect:XLR3MCCON6
1iCE40-HX1K-TQ144Housings_QFP:TQFP-144_20x20mm_Pitch0.5mmU7

Similar boards

  • 2 layers88.9 × 114.3 mmRaw, the printed circuit board in 3D

    Raw

    PCBench/PCBench

    resolution = [0.5, 0.5] pcbfolder = '../PCBs/' pcbnames = ["1Bitsy1bitsy"] iters = 30 env = PCBRoutingEnv(resolution=resolution, pcbfolder=pcbfolder, pcbnames=pcbnames) obs, info = env.reset() for in range(iters): act =…

    190 parts21MIT
  • 2 layers70 × 79 mmIntegrated circuits, the printed circuit board in 3D

    Integrated circuits

    LilyTronics/lily_kicad_lib

    KiCad library by LilyTronics

    37 parts2MIT
  • 2 layers35 × 14 mmDongle, the printed circuit board in 3D

    Dongle

    iTeleTram/dongle_hw

    USB to DCC dongle hardware schematics for KiCad

    39 partsApache-2.0
  • 4 layers53.3 × 68.6 mmHamShield1, the printed circuit board in 3D

    HamShield1

    EnhancedRadioDevices/HamShield1

    HamShield 1.0 Hardware

    381 parts8
  • 2 layers82.6 × 48.9 mmGlitch adaptor v3, the printed circuit board in 3D

    Glitch adaptor v3

    wanming2008/glitch_adaptor_v3

    Voltage glitching driver board using LM5134 and IRF7607

    45 parts1
  • 4 layers160 × 62 mmGp4-hil, the printed circuit board in 3D

    Gp4-hil

    azonenberg/openfpga

    Open FPGA tools

    450 parts259

Questions

What parts does the Wiggle spine use?

173 parts, built around the SIP32408EVB, SN75176BD, PLR135/T8 and RT8299AZQW. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Wiggle spine KiCad files?

From the gitter-badger/wiggleport repository on GitHub, at the commit this page was made from: the board is boards/spine/wiggle-spine.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Wiggle spine design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).