

Glitch adaptor v3
Voltage glitching driver board using LM5134 and IRF7607
- Size
- 82.6 × 48.9 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 45
- Nets
- 14
- Pads
- 130
- Tracks, vias
- 302, 0
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 31 Aug 2017
- Updated
- 24 Aug 2017
Overview
Glitch adaptor v3 is an open-source printed circuit board by wanming2008, from the wanming2008/glitch_adaptor_v3 repository on GitHub. It is a 2-layer board of 82.6 × 48.9 mm with 45 parts on 14 nets, routed with 302 tracks and 0 vias.
It is built around the LM5134BMF, LM7805CT and NC7WZ14P6, with the IRF7807TRPBF among its other parts. Its parts include 20 capacitors, 15 connectors, 5 ICs, 3 resistors and 2 transistors.
Main components
4LM5134BMF
SOT-23-6-40℃~+125℃ 1 2ns 3ns 4.5A 4V~12.6V 7.6A 800uA Low Side MOSFET Under Voltage Protection SOT-23-6 Gate Drivers ROHSTexas InstrumentsGate DriversLM7805CT
TO-2200℃~+70℃@(Ta) 1 1A 20V 2V@(1A) 40uV 5V 62dB@(120Hz) 8mA Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive TO-220 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsNC7WZ14P6
SC-88(SC-70-6)-40℃~+85℃ 1.5V~3.6V 1.8V~5.5V 1uA 2 32mA 32mA 4.9ns@5V,50pF 900mV~2.3V Power shutdown protection、Noise suppression function SC-88(SC-70-6) Inverters ROHSonsemiInvertersIRF7807TRPBF
SOIC-817nC@4.5V 1V 2.5W 25mΩ@4.5V 30V 8.3A N-Channel ±12V SOIC-8 MOSFETsInfineon TechnologiesMOSFETs
README
README.mdglitch_adaptor_v3
Voltage glitching driver board using LM5134 and IRF7607.
This is designed for use with the ChipWhisperer-Lite. For best performance, physically remove or disconnect the built-in glitching FETs on the CW-Lite board and connect the gate drive signal to this glitching board via coax. The connection from glitch board to target Vcore signal should be very short, I used about a centimeter of twisted heavy-gauge magnet wire. The FET drivers run from 12.5 volts to get the fastest slew rates we can. This circuit switches in a capacitor bank to stabilize Vcore when not glitching, intended for use with chips that have a low voltage core with a built-in regulator.
Board layout for KiCad, thrown together for quick assembly using the parts I had on hand. You may want to substitute your favorite voltage regulators if you like.
Parts
45| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 4u7 | Capacitors_SMD:C_1206_HandSoldering | C1, C3, C4, C5, C6, C19 |
| 5 | 0.1u | Capacitors_SMD:C_0805_HandSoldering | C2, C9, C10, C17, C20 |
| 4 | 10n | Capacitors_SMD:C_0805_HandSoldering | C11, C12, C13, C16 |
| 3 | 1uF | Capacitors_SMD:C_0805_HandSoldering | C7, C8, C18 |
| 2 | 10 | Resistors_SMD:R_0805_HandSoldering | R2, R3 |
| 2 | 57p | Capacitors_SMD:C_0805_HandSoldering | C14, C15 |
| 2 | IRF7807TRPBF | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | Q1, Q2 |
| 2 | LM5134 | TO_SOT_Packages_SMD:SOT-23-6_Handsoldering | U4, U5 |
| 1 | 12.5V IN | Connectors:BARREL_JACK | CON1 |
| 1 | 12V Probe | ScopeProbe3pin:ScopeProbe3pin | P3 |
| 1 | 3V3 Probe | ScopeProbe3pin:ScopeProbe3pin | P7 |
| 1 | 3v3 Output | Pin_Headers:Pin_Header_Straight_1x02 | P8 |
| 1 | 47k | Resistors_SMD:R_0805_HandSoldering | R1 |
| 1 | 5V Output | Pin_Headers:Pin_Header_Straight_1x02 | P6 |
| 1 | 5V Probe | ScopeProbe3pin:ScopeProbe3pin | P4 |
| 1 | BNC | Connectors:SMB_Straight | P14 |
| 1 | Capbank Probe | ScopeProbe3pin:ScopeProbe3pin | P11 |
| 1 | Gate1 Probe | ScopeProbe3pin:ScopeProbe3pin | P10 |
| 1 | Gate2 Probe | ScopeProbe3pin:ScopeProbe3pin | P9 |
| 1 | Glitch Input | Pin_Headers:Pin_Header_Straight_1x02 | P1 |
| 1 | Glitch Input Probe | ScopeProbe3pin:ScopeProbe3pin | P2 |
| 1 | Glitch Probe | ScopeProbe3pin:ScopeProbe3pin | P5 |
| 1 | LM7805CT | TO_SOT_Packages_THT:TO-220_Neutral123_Horizontal_LargePads | U2 |
| 1 | MCP1703A-3302/MB | TO_SOT_Packages_THT:TO-92_Rugged | U3 |
| 1 | NC7WZ14 | TO_SOT_Packages_SMD:SC-70-6_Handsoldering | U1 |
| 1 | Vcore | Pin_Headers:Pin_Header_Straight_1x02 | P13 |
| 1 | Vcore Probe | ScopeProbe3pin:ScopeProbe3pin | P12 |
Similar boards
- 4 layers94.1 × 59.1 mm

- 4 layers53.3 × 68.6 mm

- 2 layers

Wiggle spine
gitter-badger/wiggleport
Modular I/O for multi-channel sound, light, and motion
173 partsMIT - 2 layers88.9 × 114.3 mm

Raw
PCBench/PCBench
resolution = [0.5, 0.5] pcbfolder = '../PCBs/' pcbnames = ["1Bitsy1bitsy"] iters = 30 env = PCBRoutingEnv(resolution=resolution, pcbfolder=pcbfolder, pcbnames=pcbnames) obs, info = env.reset() for in range(iters): act =…
190 parts21MIT - 2 layers173 × 85 mm

Audio board
EleonoreMizo/pedalevite
Pédale Vite — DIY multi-FX pedalboard for guitar/bass/etc.
268 parts101WTFPL - 2 layers169.3 × 128 mm

PSU PCB
ThomasVDD/SmartSupply
SmartSupply is a digital battery powered lab powersupply. It is Arduino compatible and can be controlled via PC over USB.
134 parts96 - 2 layers

T41-Main+RF board V012
DRWJSCHMIDT/T41
This is the repository for the officially released V10, V11, and V12 versions of the T41 Software Defined Transceiver hardware and kits.
255 parts66 - 4 layers97.6 × 145.1 mm

Analog and ad9958
balmerdx/BalmerDX_VNA
Vector Network Analyzer 10 KHz - 180 MHz
226 parts26BSD-2-Clause
Questions
How big is the Glitch adaptor v3 PCB?
It measures 82.6 × 48.9 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Glitch adaptor v3 use?
45 parts, built around the LM5134BMF, LM7805CT, NC7WZ14P6 and IRF7807TRPBF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Glitch adaptor v3 KiCad files?
From the wanming2008/glitch_adaptor_v3 repository on GitHub, at the commit this page was made from: the board is glitch_adaptor_v3.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Glitch adaptor v3 design in my own project?
Its repository states no licence, so its author keeps all rights: ask wanming2008 before reusing the design.