
GR ATTiny xx4 USB
GadgetReboot/ATTiny_xx4_USB
ATTiny 14 pin device USB breakout pcb for 0-Series and 1-Series

Breakout PCB for the ESP32-A1S module including an audio amp and basic GPIO headers, USB interface
GR ESP32-A1S is an open-source printed circuit board by GadgetReboot, from the GadgetReboot/ESP32-A1S repository on GitHub. It is a 2-layer board of 79.9 × 41.4 mm with 65 parts on 72 nets, routed with 573 tracks and 139 vias.
It is built around the ESP32-A1S, CH340G and TDA2822D, with the PESD5V0S1BL, MMBT3904 and MF-FSMF050X-2 among its other parts. Its parts include 25 capacitors, 15 connectors, 11 resistors, 4 ICs and 4 diodes. It belongs with the audio and music and interfaces and adapters boards and the ESP32 boards of this library.
Breakout PCB for the ESP32-A1S module including an audio amp and basic GPIO headers, USB interface
In Arduino IDE, the ESP32 board to choose is "ESP32 Dev Module"
Use default configuration settings
Then Enable PSRAM
The USB Micro-B connector on the board is GCT p/n USB3076-30-A available from Digikey, Mouser etc
| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1, C6, C11, C15, C16, C20, C21, C22 |
| 8 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1, J7, J8, J9, J10, J12, J15, J16 |
| 4 | 100uF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C13, C14, C18, C19 |
| 3 | 10K | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1, R7, R10 |
| 3 | 10uF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C7, C8, C23 |
| 3 | 1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C5, C24, C25 |
| 3 | PESD5V0S1BL | _Custom_Footprints:SOD-882 | D1, D2, D3 |
| 2 | 10K | Potentiometer_THT:Potentiometer_Vishay_T73YP_Vertical | R8, R11 |
| 2 | 22pF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C9, C10 |
| 2 | 22r | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R13, R14 |
| 2 | 39pF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C12, C17 |
| 2 | 4.7uF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C3, C4 |
| 2 | 4r7 | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R9, R12 |
| 2 | Conn_02x06_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x06_P2.54mm_Vertical | J6, J14 |
| 2 | MMBT3904 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 1 | 12MHz | Crystal:Crystal_SMD_HC49-SD_HandSoldering | Y1 |
| 1 | 1K | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R2 |
| 1 | 22uF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C2 |
| 1 | 680r | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R15 |
| 1 | AP1117-33 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | CH340G | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U3 |
| 1 | Conn_02x04_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J4 |
| 1 | ESP32-A1S | _Custom_Footprints:ESP32-A1S | U2 |
| 1 | Headphones | Connector_Audio:Jack_3.5mm_PJ320D_Horizontal | J11 |
| 1 | LOGO | _Custom_Footprints:pcb way logo | G*** |
| 1 | Line In | Connector_Audio:Jack_3.5mm_PJ320D_Horizontal | J13 |
| 1 | MF-FSMF050X | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | F1 |
| 1 | Power | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D4 |
| 1 | Reset | Button_Switch_SMD:SW_SPST_FSMSM | SW1 |
| 1 | SPI | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | TDA2822 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_GCT_USB3076-30-A | J5 |

GadgetReboot/ATTiny_xx4_USB
ATTiny 14 pin device USB breakout pcb for 0-Series and 1-Series


immortal-sniper1/cross_band_handy_walkie_talkie
cross band handy walkie talkie. This HT would include 2 SA818s, one for 70cm and one for 2m and could be used for satellite work.

ballhog/calyx-level
Wired, fail-safe auto top-off (ATO) for a reef system. Part of the Corallite Calyx family (wired connected devices: Calyx-Outlet, Calyx-Sense, Calyx-Level).



eljotx/SDR-TRX-on-ESP32-A1S
This repository describes an SDR transceiver based on the ESP32 A1S processor, using an ILI9341 color touchscreen display, and a Si5351 oscillator.

Oleg-mk/MOST25-to-AUDIO
Passive MOST25 listener: Tang Nano 20K FPGA, ESP32 host, stereo I2S out with the head unit's volume, balance and tone
It measures 79.9 × 41.4 mm and has 2 copper layers, 1.6 mm thick.
65 parts, built around the ESP32-A1S, CH340G, TDA2822D and PESD5V0S1BL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the GadgetReboot/ESP32-A1S repository on GitHub, at the commit this page was made from: the board is KiCad/GR_ESP32-A1S.kicad_pcb and its schematic KiCad/GR_ESP32-A1S.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask GadgetReboot before reusing the design.