

PRJ2-CORRIGIDO
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 53
- Nets
- 58
- Pads
- 262
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 1 Jul 2025
- Updated
- 1 Jul 2025
Overview
PRJ2-CORRIGIDO is an open-source printed circuit board by gabrielgomes16, from the gabrielgomes16/SEMB repository on GitHub. It is a 2-layer board with 53 parts on 58 nets.
It is built around the AMS1117-3.3, LM393 and MMBT3906. Its parts include 20 capacitors, 11 resistors, 6 diodes, 4 ICs and 4 connectors. It belongs with the STM32 boards of this library.
Main components
3AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLM393
SOP-8-16V~16V 0℃~+70℃ 2 2.5mA 250nA 2V~36V 36V 5mV 5nA Fail-safe function Open-drain SOP-8 Comparators ROHSMSKSEMIComparatorsMMBT3906
SOT-23-55℃~+150℃ 1 PNP 100 100nA 200mA 200mW 300MHz 300mV 40V 5V PNP SOT-23 Bipolar (BJT) ROHSTWGMCBipolar (BJT)
Parts
53| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 100nF | Capacitor_SMD:C_0201_0603Metric | C1, C3, C4, C5, C6, C7, C8, C13, C14 |
| 4 | 10pF | Capacitor_SMD:C_0201_0603Metric | C9, C10, C11, C12 |
| 4 | 1k | Resistor_SMD:R_0201_0603Metric | R6, R7, R8, R9 |
| 3 | LED | LED_SMD:LED_0603_1608Metric | D1, D3, D4 |
| 2 | 10uF | Capacitor_SMD:C_0201_0603Metric | C15, C16 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R10, R11 |
| 2 | 1uF | Capacitor_SMD:C_0201_0603Metric | C17, C18 |
| 2 | 4k9 | Resistor_SMD:R_0201_0603Metric | R3, R4 |
| 2 | SW_SPST | Button_Switch_THT:SW_PUSH_6mm | SW1, SW3 |
| 1 | 104 | Capacitor_SMD:C_0402_1005Metric | C20 |
| 1 | 104nF | Capacitor_SMD:C_0402_1005Metric | C19 |
| 1 | 10K | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R5 |
| 1 | 10k | Potentiometer_THT:Potentiometer_Bourns_3266Y_Vertical | RV1 |
| 1 | 1K | Resistor_SMD:R_0201_0603Metric | R2 |
| 1 | 1µF | Capacitor_SMD:C_0201_0603Metric | C2 |
| 1 | 32.768 Hz | Crystal:Crystal_SMD_2012-2Pin_2.0x1.2mm | Y1 |
| 1 | 8 MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y2 |
| 1 | 9V | Package_TO_SOT_SMD:TO-252-3_TabPin2 | J2 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | D | Diode_SMD:D_SOD-123 | D2 |
| 1 | Entrada do Sinal | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Horizontal | J4 |
| 1 | LM393 | Package_TO_SOT_SMD:SOT-223-8 | U4 |
| 1 | MMBT3906 | Package_TO_SOT_SMD:SOT-23 | Q2 |
| 1 | NHD-C0220BIZ | Display:NHD-C0220BiZ | U3 |
| 1 | Power LED | LED_SMD:LED_0402_1005Metric | D6 |
| 1 | SANYOU_SRD_Form_C | Relay_THT:Relay_SPDT_SANYOU_SRD_Series_Form_C | K1 |
| 1 | STM32F411CCUx | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U1 |
| 1 | SW_Push_Dual_x2 | Button_Switch_THT:SW_PUSH_6mm | SW2 |
| 1 | Trigger LED | LED_SMD:LED_0402_1005Metric | D5 |
| 1 | ~ | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Horizontal | J3 |
| 1 | ~ | Connector_PinHeader_1.00mm:PinHeader_1x05_P1.00mm_Vertical | J1 |
More from gabrielgomes16/SEMB
1- 2 layers92.2 × 51.9 mm

Similar boards
- 2 layers133 × 98 mm

Precharge
michaelruppe/FSAE
Projects for Formula SAE Electric Vehicle competition (Australia 2019/2020)
121 parts59MIT - 2 layers49 × 49 mm

EL Load Reverse Polarity
fietser28/EL-Load
The DCL8010 electronic load module features a DC Electronic Load with several modes and protections. This project is the for the development boards for this project. There is a seperate git project for the firmware.
63 parts15 - 2 layers133 × 98 mm

Precharge
LSUTigerRacing/Electronics
This repository contains all of the KiCad Schematics for the 2026 TigerRacing Formula SAE's Electronics Subsystem.
121 parts8 - 2 layers10 × 104 mm

Analog to pwm
adeboni/laser-projector
This project is for a quadruple laser projection controller, aimed at supporting room-scale projections
51 partsGPL-3.0 - 4 layers99 × 53.3 mm

PSLab
fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io
199 parts1.7kApache-2.0 - 2 layers104 × 43.3 mm

Serial snooper
can-caglar/Data-Logger-STM32
The Serial Snooper is a UART data logger with automatic baud rate detection, real-time data stamping and a command-line-interface for configuration, running on an STM32F3 microcontroller.
101 parts4 - 2 layers59.5 × 27 mm

Desk lamp cc2530
Czubixx/zigbee-desk-lamp
DIY Zigbee desk lamp based on CC2530 controllable smart light for workbench/desk use.
28 parts - 2 layers120 × 90 mm

PLC STM32 Modbus
danhmanu/PLC-STM32F407VET6
Mạch nguyên lý KiCad 10 cho bộ PLC: điều khiển qua LAN bằng Modbus TCP (module W5500 Lite), nạp code qua USB‑C (CH340C), 16 ngõ ra transistor cách ly quang, 10 ngõ vào analog 4–20mA.
264 parts
Questions
What parts does the PRJ2-CORRIGIDO use?
53 parts, built around the AMS1117-3.3, LM393 and MMBT3906. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the PRJ2-CORRIGIDO KiCad files?
From the gabrielgomes16/SEMB repository on GitHub, at the commit this page was made from: the board is PRJ - SEMB/PRJ-2/PRJ2-CORRIGIDO/PRJ2-CORRIGIDO.kicad_pcb and its schematic PRJ - SEMB/PRJ-2/PRJ2-CORRIGIDO/PRJ2-CORRIGIDO.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the PRJ2-CORRIGIDO design in my own project?
Its repository states no licence, so its author keeps all rights: ask gabrielgomes16 before reusing the design.