2 layers35.9 × 62.7 mm
Rp2040-memcard
sd2psx/pcb
The PCB must be produced in 0.8mm thickness. Production files are provided under the "Releases" tab. These do not include the through-hole OLED module.
60 parts241
2 layers32.2 × 59.4 mm
Flipper mce
FlipperMCE/pcb21FlipperMCE PCB
- Size
- 32.2 × 59.4 mm
- Copper layers
- 2
- Thickness
- 0.8 mm
- Parts
- 70
- Nets
- 92
- Pads
- 291
- Tracks, vias
- 750, 151
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 23 Jun 2025
- Updated
- 24 Sep 2025
Overview
Flipper mce is an open-source printed circuit board by FlipperMCE, from the FlipperMCE/pcb repository on GitHub, published under the MIT licence. It is a 2-layer board of 32.2 × 59.4 mm with 70 parts on 92 nets, routed with 750 tracks and 151 vias.
It is built around the RP2040, W25Q16JVUXIQ and TF-01A, with the LY68L6400SLIT, XC6206P332MR and B5819WS among its other parts. Its parts include 23 capacitors, 17 resistors, 4 ICs, 3 diodes and 3 switches. It belongs with the RP2040 boards of this library.
Main components
7
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
W25Q16JVUXIQ
USON-8-EP(2x3)-40℃~+85℃ 100,000 cycles 10uA 133MHz 16Mbit 2.7V~3.6V 20 Years 3ms SPI USON-8-EP(2x3) NOR FLASH ROHSWinbond ElecNOR FLASH
TF-01A
SMD1.85mm Connector and Ejector MicroSD Card (TF Card) Push-Push With Locating Pins SMD SD Card / Memory Card Connector ROHSHRO ElectronicsSD Card / Memory Card Connector
LY68L6400SLIT
SOP-8SRAMLyontek Inc.
XC6206P332MR
SOT-23-40℃~+85℃@(Ta) 1 1uA 200mA 3.3V 6V Fixed Over Current Protection Positive SOT-23-3L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTorex SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
B5819WS
SOD-323-55℃~+125℃ 1A 1mA@40V 25A 40V 900mV@3A Independent SOD-323 Schottky Diodes ROHSMDDSchottky Diodes
1N4148WT
SOD-523-55℃~+150℃ 1.25V@150mA 100V 150mA 150mW 1uA@75V 2A 4ns Independent SOD-523 Switching Diodes ROHShongjiachengSwitching Diodes
README
README.mdFlipperMCE - PCB and Case
This repository contains the pcb files and the case for FlipperMCE - a GameCube Memory Card Emulator.
PCB
Production files (gerbers/bom/cpl) for JLCPCB can be found in the releases section.
When ordering the PCB, make sure to use the following settings:
- 0.8 mm thickness
- ENIG finish
For the "connector" version, a display needs to be ordered separately. Make sure, the display has a 0.5mm pitch with 30 Pins. These displays can be found at aliexpress or other market places.
Case
The case files are located in the case folder. For normal use, you would print:
- FlipperMCE_Bottom_v1.stl
- FlipperMCE_top_v1.stl
- FlipperMCE_Buttons_v1.stl
- either FlipperMCE_DisplayBracket_v1.stl or FlipperMCE_DisplayBracket_alter_v1.stl
Make sure to follow the assembly guide at https://flippermce.github.io .
Special Thanks
Special thanks goes to BitFunX (@gameBitfunx) for providing the pcb and case files for FlipperMCE <3!
Parts
70| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9, TP10, TP11, TP12, TP13, TP14 |
| 10 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C2, C3, C4, C5, C6, C7, C8, C22, C23 |
| 4 | 1u | Capacitor_SMD:C_0402_1005Metric | C9, C10, C13, C14 |
| 4 | 22 | Resistor_SMD:R_0402_1005Metric | R4, R5, R11, R16 |
| 3 | 220 | Resistor_SMD:R_0402_1005Metric | R12, R13, R14 |
| 3 | 4.7K | Resistor_SMD:R_0402_1005Metric | R6, R7, R8 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R10, R17 |
| 2 | 1uF | Capacitor_SMD:C_0402_1005Metric | C12, C15 |
| 2 | 4.7u | Capacitor_SMD:C_0603_1608Metric | C16, C17 |
| 2 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C18, C21 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R2, R3 |
| 2 | 5p | Capacitor_SMD:C_0402_1005Metric | C19, C20 |
| 2 | B5819WS | Diode_SMD:D_SOD-323 | D2, D3 |
| 1 | 0 | Resistor_SMD:R_0402_1005Metric | R18 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R9 |
| 1 | 12 Mhz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 1N4148WT | Diode_SMD:D_SOD-523 | D4 |
| 1 | 2.2uF | Capacitor_SMD:C_0603_1608Metric | C11 |
| 1 | 390K | Resistor_SMD:R_0402_1005Metric | R15 |
| 1 | LOGO | Library:flipper-LOGO | G*** |
| 1 | LY68L6400SLIT | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | OLED-128O064D | Library:GC_OLED_096 | DS1 |
| 1 | RP2040 | Library:RP2040-QFN-56 | U3 |
| 1 | TF-01A | Library:TF-SMD_TF-01A | Card1 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J3 |
| 1 | USER | Library:SW-SMD_TS24CA | SW3 |
| 1 | USER1 | Library:SW-SMD_TS24CA | SW1 |
| 1 | USER2 | Library:SW-SMD_TS24CA | SW2 |
| 1 | W25Q16JVUXIQ | Library:USON-8_2x3mm_P0.5mm | U5 |
| 1 | XC6206P332MR | Package_TO_SOT_SMD:SOT-23 | U2 |
| 1 | ~ | Library:GC_MEMCARD | J2 |
Questions
How big is the Flipper mce PCB?
It measures 32.2 × 59.4 mm and has 2 copper layers, 0.8 mm thick.
What parts does the Flipper mce use?
70 parts, built around the RP2040, W25Q16JVUXIQ, TF-01A and LY68L6400SLIT. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Flipper mce KiCad files?
From the FlipperMCE/pcb repository on GitHub, at the commit this page was made from: the board is soldered/flipper-mce.kicad_pcb and its schematic connector/flipper-mce.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Flipper mce design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 4 layers21 × 51 mm
Easyduino RP2040
Hanqaqa/Easyduino
Easily dive into different PCB KiCad designs of the most popular microcontroller devboards
65 parts755CERN-OHL-P-2.0 - 2 layers285.1 × 94.6 mm
YM60JIS PCB
ymkn/YM60JIS
A JIS layout 60% hot swappable custom mechanical keyboard PCB powered by RP2040.
173 parts10MIT - 2 layers285.1 × 94.6 mm
YuTofu PCB
ymkn/YuTofu
YuTofu is an unofficial compatible PCB for the well-known custom keyboard Tofu60 2.0.
169 parts5MIT - 2 layers228.8 × 76.2 mm
- 2 layers285.1 × 94.6 mm
- 2 layers36.7 × 27.7 mm
- 4 layers21 × 51 mm
