2 layers285.1 × 94.6 mm
YM60JIS PCB
ymkn/YM60JIS
A JIS layout 60% hot swappable custom mechanical keyboard PCB powered by RP2040.
173 parts10MIT
2 layers285.1 × 94.6 mm
YuTofu PCB
ymkn/YuTofu5YuTofu is an unofficial compatible PCB for the well-known custom keyboard Tofu60 2.0.
- Size
- 285.1 × 94.6 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 169
- Nets
- 118
- Pads
- 889
- Tracks, vias
- 1,142, 162
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 26 May 2024
- Updated
- 9 Jun 2024
Overview
YuTofu PCB is an open-source printed circuit board by ymkn, from the ymkn/YuTofu repository on GitHub, published under the MIT licence. It is a 2-layer board of 285.1 × 94.6 mm with 169 parts on 118 nets, routed with 1,142 tracks and 162 vias.
It is built around the RP2040, W25Q16JVUXIQ and SMF05CT1G, with the XC6206P332MR, 1N4148W and TS-1187A-B-A-B among its other parts. Its parts include 64 diodes, 64 switches, 17 capacitors, 7 resistors and 4 ICs. It belongs with the keyboards and input boards and the RP2040 boards of this library.
Main components
8
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
W25Q16JVUXIQ
USON-8-EP(2x3)-40℃~+85℃ 100,000 cycles 10uA 133MHz 16Mbit 2.7V~3.6V 20 Years 3ms SPI USON-8-EP(2x3) NOR FLASH ROHSWinbond ElecNOR FLASH
SMF05CT1G
SOT-363-55℃~+125℃ 100W 100nA 10V 1A 30pF 5 5V 6V IEC 61000-4-2、IEC 61000-4-4 TVS SOT-363 ESD and Surge Protection (TVS/ESD) ROHSGOODWORKESD And Surge Protection (TVS/ESD)
XC6206P332MR
SOT-23-40℃~+85℃@(Ta) 1 1uA 200mA 3.3V 6V Fixed Over Current Protection Positive SOT-23-3L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTorex SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
1N4148W
SOD-123150mA 1A 1V@50mA 1uA@75V 400mW 4ns 75V Independent SOD-123 Switching Diodes ROHSSTMicroelectronicsSwitching Diodes
TS-1187A-B-A-B
SMD-4P,5.1x5.1mm-30℃~+85℃ 1.5mm 1.6N 100,000 cycles 12V 5.1mm 5.1mm 50mA Gold No Round Button SPST Surface Mount,Vertical Without Bracket SMD-4P,5.1x5.1mm Tactile Switches ROHSXKB ConnectionTactile Switches
TYPE-C-31-M-12
SMD-30℃~+80℃ 1 10,000 cycles 16P 20V 5A 7.35mm Female Surface Mount, Right Angle Type-C SMD USB Connectors ROHSHRO ElectronicsUSB Connectors
X322512MSB4SI
SMD3225-4P-40℃~+85℃ 12MHz 20pF 80Ω Crystal Oscillator ±10ppm ±20ppm SMD3225-4P Crystals ROHSYXCCrystals
README
README.mdYuTofu
YuTofu is an unofficial compatible PCB for the well-known custom keyboard Tofu60 2.0.
Based on an ANSI layout with splitted right-Shift and 6.25u spacebar, the spacebar area has been divided into 1.25u, 2.25u, and 2.75u sections. This allows for more effective use of the thumbs.
YuTofu is equipped with a 4-pin JSF socket compatible with Unified Daughterboard, in addition to an onboard USB Type-C connector and mounting holes compatible with the GH60-compatible layout. This means that the PCB can be used not only in the Tofu60 2.0 case but also in common GH60-compatible cases, i.e. Tofu60 Redux Case.
Default Layout
You can customize the layout with Vial configurator.
Specification
- Hot swappable sockets for MX compatible switches are installed
- Unified-Daughterboard JSF 4-pin socket and USB Type C Connector (USB 2.0) are equipped
- PCB and switch plate compatible with the Tofu60 2.0
- GH60 compatible dimension: 285mm(w) x 94.6mm(h) x 1.6mm(d)
- Suitable for Tofu60 2.0 case, and also may be used for most 60% keyboard cases
- Warning: center and right bottom mounting holes are not implemented.
- Warning: switch plate cannot be used with cases other than the Tofu60 2.0.
Build Guide
LICENSE
This project is licensed under the MIT License, see the LICENSE file for details.
Parts
169| Qty | Value | Footprint | References |
|---|---|---|---|
| 64 | 1N4148W | Diode_SMD:D_SOD-123 | D1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +48 |
| 49 | SW_Push | PCM_marbastlib-mx:SW_MX_HS_CPG151101S11_1u | SW1, SW11, SW12, SW13, SW14, SW16, SW17, SW18, SW19, SW21, SW22, SW23, SW24, SW25, SW26, SW27 +33 |
| 11 | 100nF | Capacitor_SMD:C_0402_1005Metric | C3, C4, C5, C6, C7, C8, C9, C10, C13, C16, C17 |
| 8 | SW_Push | PCM_marbastlib-mx:SW_MX_HS_CPG151101S11_1.25u | SW5, SW10, SW15, SW20, SW52, SW57, SW62, SW67 |
| 2 | 10uF | Capacitor_SMD:C_0402_1005Metric | C1, C2 |
| 2 | 1uF | Capacitor_SMD:C_0402_1005Metric | C11, C12 |
| 2 | 20pF | Capacitor_SMD:C_0402_1005Metric | C14, C15 |
| 2 | 27 | Resistor_SMD:R_0603_1608Metric | R4, R5 |
| 2 | 5.1K | Resistor_SMD:R_0402_1005Metric | R1, R3 |
| 2 | SW_Push | PCM_marbastlib-mx:SW_MX_HS_CPG151101S11_1.75u | SW3, SW56 |
| 1 | hole:PKRH | ||
| 1 | 10kΩ | Resistor_SMD:R_0402_1005Metric | R7 |
| 1 | 1K | Resistor_SMD:R_0402_1005Metric | R8 |
| 1 | 1KΩ | Resistor_SMD:R_0402_1005Metric | R6 |
| 1 | >VALUE | hole:PKRH | |
| 1 | Backslash | PCM_marbastlib-mx:SW_MX_HS_CPG151101S11_1.5u | SW64 |
| 1 | Backspace | PCM_marbastlib-mx:SW_MX_HS_CPG151101S11_1u | SW63 |
| 1 | Conn_01x04_MountingPin | Connector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | J2 |
| 1 | Enter | PCM_marbastlib-mx:SW_MX_HS_CPG151101S11_1u | SW65 |
| 1 | LOGO | logo:yutofu_icon | G*** |
| 1 | LOGO | logo:yutofu_logo | G*** |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U3 |
| 1 | SMF05CT1G | SMF05CT1G:SOT-363-6_2P2X1P35_ONS | U2 |
| 1 | SW_Push | PCM_marbastlib-mx:SW_MX_HS_CPG151101S11_1.5u | SW2 |
| 1 | Space | PCM_marbastlib-mx:SW_MX_HS_CPG151101S11_1u | SW29 |
| 1 | TS-1187A-B-A-B | Button_Switch_SMD:SW_Push_1P1T_XKB_TS-1187A | BTN1 |
| 1 | TYPE-C-31-M-12 | PCM_marbastlib-various:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | W25Q16JVUXIQ | W25Q16JVUXIQ:W25Q16JVUXIQ_WIN | U4 |
| 1 | X322512MSB4SI | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | XC6206P332MR | Package_TO_SOT_SMD:SOT-23-3 | U1 |
The 164 most common of 169 parts.
Questions
How big is the YuTofu PCB PCB?
It measures 285.1 × 94.6 mm and has 2 copper layers, 1.6 mm thick.
What parts does the YuTofu PCB use?
169 parts, built around the RP2040, W25Q16JVUXIQ, SMF05CT1G and XC6206P332MR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the YuTofu PCB KiCad files?
From the ymkn/YuTofu repository on GitHub, at the commit this page was made from: the board is KiCAD/PCB/YuTofu_PCB.kicad_pcb and its schematic KiCAD/PCB/YuTofu_PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the YuTofu PCB design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 2 layers285.1 × 94.6 mm
- 2 layers228.8 × 76.2 mm
- 2 layers
- 4 layers227.5 × 75.2 mm
- 2 layers353.1 × 124.9 mm
- 2 layers42 × 98.1 mm
- 2 layers209.6 × 66.7 mm
