2 layers385 × 127.3 mm
2 layers
Keyboard
joshajohnson/keyboard-templateA starting point for all my RP2040 based boards.
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 53
- Nets
- 67
- Pads
- 229
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 6 (file 20211014)
- Created
- 5 Oct 2022
- Updated
- 5 Oct 2022
Overview
Keyboard is an open-source printed circuit board by joshajohnson, from the joshajohnson/keyboard-template repository on GitHub. It is a 2-layer board with 53 parts on 67 nets.
It is built around the RP2040, W25Q128JVSIQ and SN74AHCT1G125DBVR(UMW), with the SRV05-4-P-T7, XC6206P332MR and 0402CG200J500NT among its other parts. Its parts include 22 capacitors, 14 resistors, 5 ICs, 3 transistors and 3 connectors. It belongs with the keyboards and input boards and the RP2040 boards of this library.
Main components
12
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
SN74AHCT1G125DBVR(UMW)
SOT-23-5-40℃~+125℃ 1 1 10uA 12ns@5V,50pF 2V 3.8V、4.4V 4.5V~5.5V 440mV 74AHCT 800mV 8mA 8mA SOT-23-5 Logic Gates ROHSUMWLogic Gates
SRV05-4-P-T7
SOT-23-612V 1A@8/20us 3.5pF 500W@8/20us 5V 5uA 6V ESD Four channels IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSPROTEKESD And Surge Protection (TVS/ESD)
XC6206P332MR
SOT-23-40℃~+85℃@(Ta) 1 1uA 200mA 3.3V 6V Fixed Over Current Protection Positive SOT-23-3L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTorex SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
0402CG200J500NT
040220pF 50V C0G ±5% 0402 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSGuangdong Fenghua Advanced Tech (FH)Multilayer Ceramic Capacitors MLCC - SMD/SMT
X322512MSB4SI
SMD3225-4P-40℃~+85℃ 12MHz 20pF 80Ω Crystal Oscillator ±10ppm ±20ppm SMD3225-4P Crystals ROHSYXCCrystals
ASMD0805-050
0805-40℃~+85℃ 1.1mm 1.5mm 100A 100ms 100mΩ 1A 2.3mm 500mA 500mW 6V 850mΩ 0805 Resettable Fuses ROHSJDTfuseResettable Fuses
19-217/BHC-ZL1M2RY/3T
0603-40℃~+85℃ 110mW 120° 2.8V 24.5mcd~28.5mcd 465nm~475nm 468nm 5mA Blue Discrete Diode Water Clear 0603 LED Indication - Discrete ROHSEverlight ElectronicsLED Indication - Discrete
SM04B-SRSS-TB(LF)(SN)
SMD,P=1mm,卧贴-25℃~+85℃ 1 1A 1mm 1x4P 2.9mm 4 4.32mm 4P 50V 6mm Auxiliary Solder Pin Copper alloy PA SH Surface Mount, Right Angle Tin UL94V-0 White SMD,P=1mm,卧贴 Wire To Board Connector ROHSJSTWire To Board Connector
TS-1187A-B-A-B
SMD-4P,5.1x5.1mm-30℃~+85℃ 1.5mm 1.6N 100,000 cycles 12V 5.1mm 5.1mm 50mA Gold No Round Button SPST Surface Mount,Vertical Without Bracket SMD-4P,5.1x5.1mm Tactile Switches ROHSXKB ConnectionTactile Switches
TYPE-C-31-M-12
SMD-30℃~+80℃ 1 10,000 cycles 16P 20V 5A 7.35mm Female Surface Mount, Right Angle Type-C SMD USB Connectors ROHSHRO ElectronicsUSB Connectors
README
README.mdKeyboard Template
A starting point for all my RP2040 based boards.
To use, git clone --recursive to get all the submodules, then begin designing!
Parts
53| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C2, C3, C4, C5, C6, C7, C8, C9, C15, C21, C22 |
| 7 | 5K1 | Resistor_SMD:R_0603_1608Metric | R1, R2, R10, R11, R12, R13, R14 |
| 6 | 4u7 | Capacitor_SMD:C_0603_1608Metric | C11, C12, C13, C16, C19, C20 |
| 3 | 2N7002 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3 |
| 3 | 51K | Resistor_SMD:R_0603_1608Metric | R4, R5, R6 |
| 2 | 1K | Resistor_SMD:R_0402_1005Metric | R3, R9 |
| 2 | 1u | Capacitor_SMD:C_0402_1005Metric | C10, C14 |
| 2 | 20p | Capacitor_SMD:C_0402_1005Metric | C17, C18 |
| 2 | 27R | Resistor_SMD:R_0603_1608Metric | R7, R8 |
| 1 | 12MHz | josh-oscillators:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 500mA | josh-passives-smt:Fuse_0805_2012Metric | F1 |
| 1 | 74AHCT1G125 | josh-soic-sot-etc:SOT-23-5 | U1 |
| 1 | BLUE | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | JST SH | josh-connectors:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | J2 |
| 1 | RESET | josh-buttons-switches:SW_SPST_SKQG | SW1 |
| 1 | RP2040 | josh-dfn-qfn:RP2040-QFN-56 | U3 |
| 1 | SHORT | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | JP1 |
| 1 | SRV05-4 | josh-soic-sot-etc:SOT-23-6_SRV05 | U4 |
| 1 | SWD | josh-connectors:6_PIN_THT_Staggered | J3 |
| 1 | USB_C_Receptacle_USB2.0 | josh-connectors:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | W25Q128JVSIQ | josh-soic-sot-etc:SOIC-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | WS2812C-2020 | josh-led:WS2812C-2020 | D2 |
| 1 | XC6206P332MR | Package_TO_SOT_SMD:SOT-23 | U2 |
Questions
What parts does the Keyboard use?
53 parts, built around the RP2040, W25Q128JVSIQ, SN74AHCT1G125DBVR(UMW) and SRV05-4-P-T7. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Keyboard KiCad files?
From the joshajohnson/keyboard-template repository on GitHub, at the commit this page was made from: the board is hardware/template/keyboard.kicad_pcb and its schematic hardware/template/keyboard.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Keyboard design in my own project?
Its repository states no licence, so its author keeps all rights: ask joshajohnson before reusing the design.
Similar boards
- 2 layers100 × 100 mm
Hour meter board microfit can handroute
ilomon10/embedded-totalizer-hour-meter
ESP32 engine hour meter & totalizer: firmware, SensorFrame protocol, Node host tools, KiCad PCB and a Deno device simulator
152 parts - 2 layers285.1 × 94.6 mm
YM60JIS PCB
ymkn/YM60JIS
A JIS layout 60% hot swappable custom mechanical keyboard PCB powered by RP2040.
173 parts10MIT - 2 layers285.1 × 94.6 mm
YuTofu PCB
ymkn/YuTofu
YuTofu is an unofficial compatible PCB for the well-known custom keyboard Tofu60 2.0.
169 parts5MIT - 2 layers285.1 × 94.6 mm
- 2 layers79.9 × 28.4 mm
- 4 layers100 × 90 mm
Opentouch s3
JoeMighty/opentouch-s3
A modern remake of the Bare Conductive Touch Board: 12 capacitive touch electrodes, MP3/WAV/MIDI audio, and now WiFi, Bluetooth LE, USB-C, a proper LiPo power path, a fuel gauge, line-in, MIDI out, Qwiic and an RGB LED.
185 parts - 4 layers100 × 70 mm
SEM
Serhio4522/SEM_hitachi-
Digitization of a Hitachi scanning electron microscope (SEM) — hardware design, FPGA firmware, and analog frontend schematics.
288 parts1