

Sys pcb
- Size
- 72.8 × 63 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 76
- Nets
- 135
- Pads
- 360
- Tracks, vias
- 931, 169
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 6 May 2026
- Updated
- 7 May 2026
Overview
Sys pcb is an open-source printed circuit board by fernd4wg, from the fernd4wg/arc_exo_pcb repository on GitHub. It is a 4-layer board of 72.8 × 63 mm with 76 parts on 135 nets, routed with 931 tracks and 169 vias.
It is built around the TEENSY 4.1, TXS0104EPW and C3D16065A. Its parts include 28 resistors, 14 connectors, 7 capacitors, 7 ICs and 1 diode. It belongs with the NXP (LPC, Kinetis, i.MX RT) boards of this library.
Main components
3TEENSY 4.1
Development Boards & Kits - ARM ModuleSparkFun ElectronicsUncategorisedTXS0104EPW
TSSOP-14-40℃~+85℃ 1 1.65V~3.6V 2.3V~5.5V 24Mbps 4 Automatic direction detection、Output enable high-impedance、Integrated pull-up resistor Bidirectional Level translator Push-Pull、Open-drain TSSOP-14 Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level ShiftersC3D16065A
TO-220-21.8V@16A 39A 650V 95uA@650V TO-220-2 SiC Diodes ROHSWolfspeedSiC Diodes
README
README.mdNot much to note.
Parts
76| Qty | Value | Footprint | References |
|---|---|---|---|
| 28 | DNP | Jumper:SolderJumper-2_P1.3mm_Bridged2Bar_Pad1.0x1.5mm | R2, R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R20, R21, R22, R23, R24 +12 |
| 6 | C | Capacitor_Tantalum_SMD:CP_EIA-1608-08_AVX-J_HandSolder | C4, C5, C6, C7, C8, C9 |
| 6 | R_US | Jumper:SolderJumper-2_P1.3mm_Bridged2Bar_Pad1.0x1.5mm | 0_Ohm1, 0_Ohm3, 0_Ohm4, O_Ohm2, O_Ohm4, O_Ohm5 |
| 3 | R_US | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R_G1, R1, R3 |
| 2 | 36V | Connector_AMASS:AMASS_XT60-F_1x02_P7.20mm_Vertical | BT1, BT2 |
| 2 | TXS0104EPW | Package_SO:TSSOP-14_4.4x5mm_P0.65mm | U7, U8 |
| 2 | ~ | teensy_library:Polulu_Converter | U2, U4 |
| 1 | C3D16065A | Package_TO_SOT_THT:TO-220-2_Vertical | D1 |
| 1 | CAN_1 | Connector_Molex:Molex_PicoBlade_53261-0271_1x02-1MP_P1.25mm_Horizontal | J1 |
| 1 | CAN_2 | Connector_Molex:Molex_PicoBlade_53261-0271_1x02-1MP_P1.25mm_Horizontal | J2 |
| 1 | CAN_DRIVER | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | C_US | Capacitor_THT:CP_Axial_L21.0mm_D8.0mm_P28.00mm_Horizontal | C1 |
| 1 | I2C_1 | Connector_Molex:Molex_PicoBlade_53261-0471_1x04-1MP_P1.25mm_Horizontal | J4 |
| 1 | I2C_2 | Connector_Molex:Molex_PicoBlade_53261-0471_1x04-1MP_P1.25mm_Horizontal | J5 |
| 1 | NMOS | SQJ110EP-T1_GE3_KiCAD:SQJ160EPT1_GE3 | Q1 |
| 1 | QUAD_1 | Connector_Molex:Molex_PicoBlade_53261-0471_1x04-1MP_P1.25mm_Horizontal | J9 |
| 1 | QUAD_2 | Connector_Molex:Molex_PicoBlade_53261-0471_1x04-1MP_P1.25mm_Horizontal | J10 |
| 1 | QUAD_3 | Connector_Molex:Molex_PicoBlade_53261-0471_1x04-1MP_P1.25mm_Horizontal | J15 |
| 1 | RPI | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Vertical | J12 |
| 1 | R_DOWN_1 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R_D1 |
| 1 | R_DOWN_2 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R_D2 |
| 1 | SPI_0 | Connector_Molex:Molex_PicoBlade_53261-0671_1x06-1MP_P1.25mm_Horizontal | J8 |
| 1 | SPI_1 | Connector_Molex:Molex_PicoBlade_53261-0671_1x06-1MP_P1.25mm_Horizontal | J7 |
| 1 | SPI_2 | Connector_Molex:Molex_PicoBlade_53261-0671_1x06-1MP_P1.25mm_Horizontal | J6 |
| 1 | SPI_SHIFTER | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U6 |
| 1 | SW_DIP_x01 | Button_Switch_SMD:SW_DIP_SPSTx01_Slide_6.7x4.1mm_W8.61mm_P2.54mm_LowProfile | SW1 |
| 1 | Teensy4.1 | TEENSY_4_1:TEENSY41 | U3 |
| 1 | UART_1 | Connector_Molex:Molex_PicoBlade_53261-0471_1x04-1MP_P1.25mm_Horizontal | J3 |
| 1 | mtr_conn_0 | Connector_Molex:Molex_PicoBlade_53261-0671_1x06-1MP_P1.25mm_Horizontal | J17 |
| 1 | mtr_conn_1 | Connector_Molex:Molex_PicoBlade_53261-0671_1x06-1MP_P1.25mm_Horizontal | J18 |
The 72 most common of 76 parts.
Similar boards
- 4 layers56.5 × 65 mm

- 4 layers219 × 108.5 mm

Z80DevBoard
gianluca-rainis/Z80DevBoard
An advanced development board for the Z80 microprocessor, powered by an RP2040.
182 parts7CERN-OHL-S-2.0 - 4 layers70.5 × 79.5 mm

M4 CAN Feather Carrier
2468shrm/M4_CAN_Feather_Carrier_v6
Sixth version of the M4 Feather CAN Express carrier board. Hopefully, "the last".
70 parts1 - 2 layers83.5 × 59 mm

ESP32Breakout
GadgetReboot/ESP32_5V_Dev_Board
ESP32 dev board with on board 3.3v to 5v buffers to some external pins, PT8211 I2S DAC, and Micro SD Card Socket
37 parts1 - 4 layers91 × 110 mm

Pico Robotic Controller
2468shrm/Pico-Robotic-Controller
A carrier board for a Raspberry Pi Pico (W) for use in FRC robotics. Similar to the XRP board.
103 parts - 4 layers80 × 80 mm

Telemetry
chithigun23/ANUFS-Telemetry
To use custom hardware to measure parameters and dynamics of an ICE Formula SAE car.
159 parts - 2 layers59.1 × 49.1 mm

Desktopia
Diabltica/Desktopia
Desktopia is an open-source project for easy height control of your IKEA Skarsta/Trotten sit-stand desk, providing a comfortable and customizable workspace experience
76 parts - 6 layers63.2 × 82.3 mm

SuperSamFPGA
jimbro1000/SuperSamFPGA
SamX8 design expanded to leverage basic FPGA instead of CPLD
105 parts
Questions
How big is the Sys pcb PCB?
It measures 72.8 × 63 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Sys pcb use?
76 parts, built around the TEENSY 4.1, TXS0104EPW and C3D16065A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Sys pcb KiCad files?
From the fernd4wg/arc_exo_pcb repository on GitHub, at the commit this page was made from: the board is sys_pcb/sys_pcb.kicad_pcb and its schematic sys_pcb/escon_motors.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Sys pcb design in my own project?
Its repository states no licence, so its author keeps all rights: ask fernd4wg before reusing the design.