Skip to the content
2 layers60 × 25 mmTashTalkUSB, the printed circuit board in 3D

A modern async user space AppleTalk stack with Rust + Tokio

Size
60 × 25 mm
Copper layers
2
Thickness
1.6 mm
Parts
35
Nets
40
Pads
144
Tracks, vias
292, 64
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
27 Feb 2026
Updated
7 Nov 2026

Overview

TashTalkUSB is an open-source printed circuit board by FeralFirmware, from the FeralFirmware/TailTalk repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 60 × 25 mm with 35 parts on 40 nets, routed with 292 tracks and 64 vias.

It is built around the SP0503BAHTG. Its parts include 14 resistors, 7 capacitors, 5 diodes, 3 ICs and 3 connectors. It belongs with the PIC boards of this library.

Main components

1

README

TashTalkUSB/README.md

Overview

I sell on Tindie

This device us a USB-ified version of TashTalk by Tashtari using the original PIC12F1840 and a CP2102N USB-to-UART chip.

It uses the same firmware (v2.1.3 as of time of writing) from the original project, an an SN65HVD1473 transceiver from TI so it can be used with a regular LocalTalk cable, or a dongle like PhoneNET.

Programming PIC

These boards use a TagConnect cable for connecting to the board for programming. If using the PICkit to power the circuit during bringup ensure that the supply voltage is set to 3.3V - 5V will destroy the other chips on the board.

I use Microchip's IPE for bulk programming these devices. No extra settings need to be changed beyond the supply voltage if powering it off the PICkit. Just burn the firmware on to the device and it should be ready to go.

Programming CP2102N

The CP2102N should work out of the box, but does not have the LED alternate mode immediately enabled (so the little RX/TX LEDs light up). I use cp210x-cfg along with tashtalk-setup.sh to provision these. This script only works on Linux today but could be adapted for other platforms if needed.

This little script enables the LED mode and sets the device name and manufacturer so it comes up with a friendly name in TailTalk. It is not strictly necessary to do this of course.

The script launches and will wait for the first TashTalk USB device to be plugged in. Once detected it will then set all the values and wait for the next one to be plugged in. It is pretty helpful for mass programming these for a bulk order.

Verification

Once both the PIC and CP2102N have been programmed I typically test this by launching TailTalk, starting the server and verifying a vintage Mac can connect and see files from it. TashTalk can auto reconnect to TashTalk so if bulk testing you can simply unplug the USB and DIN cable, swap to another and then resume testing.

The tests pass if the remote Mac can successfully discover the server and query files from it, and the LEDs work on the board.

Manufacturing

I use JLCPCB for making these boards and the schematics and board files are already prepared with LCSC part numbers for each component. I've tried to choose their basic components as much as possible to keep costs down. If doing a large order panelisation is recommended as the individual boards are really small and a high cost per board is paid when not panelised.

Parts

35
QtyValueFootprintReferences
40.1uFCapacitor_SMD:C_0603_1608MetricC1, C3, C6, C8
410Resistor_SMD:R_0603_1608MetricR8, R9, R10, R11
34.7uFCapacitor_SMD:C_0603_1608MetricC2, C4, C7
2,
2100Resistor_SMD:R_0603_1608MetricR12, R13
25K1Resistor_SMD:R_0603_1608MetricR2, R3
2SM712_SOT23Package_TO_SOT_SMD:SOT-23D4, D5
110KResistor_SMD:R_0603_1608MetricR14
11KResistor_SMD:R_0603_1608MetricR1
122K1Resistor_SMD:R_0603_1608MetricR4
1240Resistor_SMD:R_0603_1608MetricR7
1300Resistor_SMD:R_0603_1608MetricR6
147K5Resistor_SMD:R_0603_1608MetricR5
1BlueLED_SMD:LED_0603_1608MetricD2
1CP2102N-Axx-xQFN20Package_DFN_QFN:SiliconLabs_QFN-20-1EP_3x3mm_P0.5mm_EP1.8x1.8mmU1
1GreenLED_SMD:LED_0603_1608MetricD3
1PIC12F1840-xSNPackage_SO:SOIC-8_3.9x4.9mm_P1.27mmU2
1SN65HVD1473DGSRPackage_SO:MSOP-10_3x3mm_P0.5mmU3
1SP0503BAHTPackage_TO_SOT_SMD:SOT-143D1
1TC2030Connector:Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_VerticalJ1
1USB_C_Receptacle_USB2.0_14PConnector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12J3
1~TashTalk:CONN-TH_DIN-802J2

The 34 most common of 35 parts.

More from FeralFirmware/TailTalk

1
  • 4 layers60 × 40 mmInkTalk, the printed circuit board in 3D

    InkTalk

    FeralFirmware/TailTalk

    A modern async user space AppleTalk stack with Rust + Tokio

    66 parts103GPL-3.0

Similar boards

  • 4 layers99 × 53.3 mmPSLab, the printed circuit board in 3D

    PSLab

    fossasia/pslab-hardware

    PSLab Hardware Design and Schematics https://pslab.io

    199 parts1.7kApache-2.0
  • 4 layers85 × 56 mmPslab mini, the printed circuit board in 3D

    Pslab mini

    fossasia/pslab-mini-hardware

    PSLab Mini Hardware https://pslab.io

    182 parts1.2kApache-2.0
  • 4 layers55 × 14.7 mmMinCab, the printed circuit board in 3D

    MinCab

    merocle/mincab

    small carrier board for Raspberry Pi CM4

    41 parts180CC-BY-SA-4.0
  • 2 layers145 × 165 mmBreakpanel, the printed circuit board in 3D

    Breakpanel

    monero-project/kastelo

    The Sekura Monero Hardware Wallet

    690 parts115
  • 6 layers203 × 151.8 mmPDNode Baseboard, the printed circuit board in 3D

    PDNode Baseboard

    DvidMakesThings/HW_PDNode-600-Pro

    The PDNode-600 is a professional-grade, 600W USB Power Delivery Unit designed specifically for compact 10-inch rack systems, targeting embedded developers, homelab enthusiasts, test benches, and smart infrastructure.

    236 parts86AGPL-3.0
  • 4 layers100 × 180 mmX65-sbc revB1, the printed circuit board in 3D

    X65-sbc revB1

    jsyk/x65

    The 65c02 and 65c816s-based modern retro computer

    344 parts59MIT
  • 2 layers58 × 38.3 mmEsp32-caliper, the printed circuit board in 3D

    Esp32-caliper

    Mew463/esp32-caliper

    It features a built in 150mAh battery and a USB C interface for charging/uploading code.

    44 parts59
  • 4 layers69.8 × 69.8 mmFreeEEG32, the printed circuit board in 3D

    FreeEEG32

    neuroidss/FreeEEG32-alpha1.0

    ALPHA1.0 TEST FAILED, USE NEW VERSION INSTEAD FreeEEG32 alpha1.0 32 channels mobile electroencephalography under GNU AGPL 24 bits, 4kSPS ADCs 4x AD7770 MCU STM32F427ZI WIFI ESP-12F (ESP8266) USB CP2102N Accel & hyro…

    217 parts39AGPL-3.0

Questions

How big is the TashTalkUSB PCB?

It measures 60 × 25 mm and has 2 copper layers, 1.6 mm thick.

What parts does the TashTalkUSB use?

35 parts, built around the SP0503BAHTG. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the TashTalkUSB KiCad files?

From the FeralFirmware/TailTalk repository on GitHub, at the commit this page was made from: the board is TashTalkUSB/TashTalkUSB.kicad_pcb and its schematic InkTalk/InkTalk.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the TashTalkUSB design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).