
Voron Klipper Board
VoronDesign/Voron-Hardware
Cool Hardware designed by the Voron Design group

Place capacitors closer to the Arduino, if that's what we want to supress noise on
HagiwoKick is an open-source printed circuit board by fablabnk, from the fablabnk/HagiwoKick_THT repository on GitHub. It is a 2-layer board of 30 × 106 mm with 37 parts on 43 nets, routed with 188 tracks and 21 vias.
It is built around the BAT43. Its parts include 11 resistors, 10 capacitors, 7 diodes and 3 connectors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Place capacitors closer to the Arduino, if that's what we want to supress noise on
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 1k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3, R4, R5, R10 |
| 6 | BAT43 | Library:D_DO-35_SOD27_P7.62mm_Horizontal_Widened_No_K | D1, D2, D3, D4, D5, D6 |
| 5 | 100pF | Capacitor_THT:C_Disc_D3.8mm_W2.6mm_P2.50mm | C1, C2, C3, C4, C5 |
| 4 | 100k B | Library:Pot_9mm_DShaft_RemovedPins4_5 | RV1, RV2, RV3, RV4 |
| 2 | 100k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R6, R8 |
| 2 | 470 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R9, R11 |
| 1 | 100nF | Capacitor_THT:C_Disc_D3.8mm_W2.6mm_P2.50mm | C6 |
| 1 | 10uF | Capacitor_THT:CP_Radial_D4.0mm_P2.00mm | C7 |
| 1 | 2.2nF | Capacitor_THT:C_Disc_D3.8mm_W2.6mm_P2.50mm | C10 |
| 1 | 2.2uF | Capacitor_THT:C_Disc_D3.8mm_W2.6mm_P2.50mm | C8 |
| 1 | 33k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R7 |
| 1 | 470nF | Capacitor_THT:C_Disc_D3.8mm_W2.6mm_P2.50mm | C9 |
| 1 | Arduino_Nano_v3.x | Module:Arduino_Nano | A1 |
| 1 | Eurorack_Power_10pin_Unshrouded | Library:IDC-Header_2x05_P2.54mm_Vertical_Euro_Power_Striped_ThickerText | PWR1 |
| 1 | LED | LED_THT:LED_D5.0mm | D7 |
| 1 | OUT | Library:EighthInch_PJ398SM_3mmNPTH | J2 |
| 1 | TONECV | Library:EighthInch_PJ398SM_3mmNPTH | J1 |
| 1 | TRIG | Library:EighthInch_PJ398SM_3mmNPTH | J3 |

VoronDesign/Voron-Hardware
Cool Hardware designed by the Voron Design group



ravinrabbid/DonCon2040
RP2040 based firmware and hardware for DIY Taiko no Tatsujin Drum Controllers

Testbild-synth/HAGIWO_arduino_oscillator
4HP through hole version of the HAGIWO FM/additive/chord oscillator with mode switch and gain input.

Testbild-synth/Hagiwo_009_030_sequencer
A through-hole PCB conversion of HAGIWO's 6 channel eurorack gate sequencer. Includes Gerbers, Code and building instructions.

bvarner/pi485
An open-source TTL UART <-> RS485 converter, intended for a Raspberry Pi or Arduino

Testbild-synth/HAGIWO-029-033-Eurorack-quantizer
Through hole PCB version of the HAGIWO Dual Quantizer/SH101 Sequencer Eurorack Module-.
It measures 30 × 106 mm and has 2 copper layers, 1.6 mm thick.
37 parts, built around the BAT43. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the fablabnk/HagiwoKick_THT repository on GitHub, at the commit this page was made from: the board is HagiwoKick.kicad_pcb and its schematic HagiwoKick.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask fablabnk before reusing the design.