Skip to the content
4 layers80 × 36.1 mmBms, the printed circuit board in 3D

An open-source 16-inch laptop designed from scratch.

Size
80 × 36.1 mm
Copper layers
4
Thickness
1.6 mm
Parts
201
Nets
99
Pads
608
Tracks, vias
2,100, 280
Pours
11
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
19 Jul 2026
Updated
20 Oct 2026

Overview

Bms is an open-source printed circuit board by EwoudVV, from the EwoudVV/ducktop2 repository on GitHub, published under the MIT licence. It is a 4-layer board of 80 × 36.1 mm with 201 parts on 99 nets, routed with 2,100 tracks and 280 vias.

It is built around the RT0603BRD07499KL, RT0603BRD07100KL and RT0603BRD0710KL, with the RC0603FR-07100KL, RC0603FR-0710KL and RC0603FR-071ML among its other parts. Its parts include 69 resistors, 47 capacitors, 4 diodes and 1 fuse. It belongs with the computers and single-board computers and power boards of this library.

Main components

12

README

radio_daughterboard/README.md

radio daughterboard

9 october 2026: this is now planned as an external plug-in accessory so the laptop can have a thinner, flush clamshell case. the radio, GNSS receiver and separate radio audio codec stay together. the saved electronics still use the internal 30-pin interface below; converting power, audio and controls to an external cable is a separate design change. no external connector or cable is released yet.

the radio/GNSS/audio board is removable. i want the rest of the laptop to work while it is absent or being revised, including normal system audio, the microphone, charging, and boot.

it contains DRA818V and DRA818U radio modules, external filters and RF switches, a MAX-M10S GNSS receiver, and a separate PCM2900C USB audio codec. power, USB, UART/control, PTT, presence, and fault signals go through the removable interface. the radio is intended to start off and stay separate from core laptop power decisions.

layout state

the 4 september board read found 126 footprints on a four-layer placement board, with no tracks or vias. the nominal outline is about 120 x 70 mm.

the stored renders show a placement-stage design. they do not prove the current chassis fit. the center-side FFC connector J2300 is now at (188,4), rotation 0, so the installed cable route and board supports need a new check. mechanical plan

source and checks

the schematic hierarchy and placement generator live in gen/:

  • generate_radio_daughterboard_project.py
  • generate_radio_daughterboard_pcb.py
  • verify_radio_daughterboard.py

generation can replace source/placement files. use a copied candidate for a deliberate change, following the rebuild guidance. direct ERC and DRC can inspect the existing files without regeneration.

remaining work

finish placement/routing, test access, the cable installation, and mechanical supports. then verify rails, default-off behavior, removal/fault handling, GNSS, control and audio paths. RF filters, antennas, transmit behavior, emissions, and coexistence need their own measured test setup.

the radio can be deferred during initial laptop bring-up. its removal must not silently break a shared bus, reset, power, or audio dependency.

Parts

201
QtyValueFootprintReferences
42.2k 1% I2C pull-upResistor_SMD:R_0603_1608MetricR2262, R2263, R2266, R2267
4220n 50V cell filterCapacitor_SMD:C_0603_1608MetricC852, C853, C854, C855
44.99R 0.1% 25ppm sense filterResistor_SMD:R_0603_1608MetricR2280, R2281, R2282, R2283
4499k 0.1% 25ppm thermal reference bottomResistor_SMD:R_0603_1608MetricR2241, R2243, R2245, R2247
475R 1% cell input/balance filterResistor_SMD:R_0603_1608MetricR841, R842, R843, R844
3100k 0.1% 25ppm cell NTC pull-upResistor_SMD:R_0603_1608MetricR2210, R2213, R2216
3100n 50V comparator supplyCapacitor_SMD:C_0603_1608MetricC2221, C2222, C2223
310k 0.1% 25ppm NTC return-lead limitResistor_SMD:R_0603_1608MetricR2212, R2215, R2218
310n 50V NTC sense filterCapacitor_SMD:C_0603_1608MetricC2211, C2212, C2213
310n 50V thermal reference filterCapacitor_SMD:C_0603_1608MetricC2240, C2241, C2242
2100R gate seriesResistor_SMD:R_0603_1608MetricR847, R848
2100k thermal CTR gate default-offResistor_SMD:R_0603_1608MetricR2235, R2238
2100n 50V I2C isolator supplyCapacitor_SMD:C_0603_1608MetricC2250, C2251
2100n 50V current guard supplyCapacitor_SMD:C_0603_1608MetricC2274, C2275
2100n 50V readiness isolator supplyCapacitor_SMD:C_0603_1608MetricC2255, C2256
210k 0.1% 25ppm NTC sense-lead limitResistor_SMD:R_0603_1608MetricR2211, R2214
210k hardware OFF default-highResistor_SMD:R_0603_1608MetricR2236, R2239
210n 50V C0G differential filterCapacitor_SMD:C_0603_1608MetricC2270, C2271
210n 50V current reference filterCapacitor_SMD:C_0603_1608MetricC2276, C2277
21M gate-sourceResistor_SMD:R_0603_1608MetricR849, R850
21k thermal CTR gate seriesResistor_SMD:R_0603_1608MetricR2234, R2237
24.7k 1% I2C pull-upResistor_SMD:R_0603_1608MetricR2260, R2261
2430R 1% 1.5W REGIN supply limiterResistor_SMD:R_2512_6332MetricR880, R881
2BAT54WS OFF-bias supply ORDiode_SMD:D_SOD-323D2220, D2221
2BZT52C15 gate-source clampDiode_SMD:D_SOD-123D847, D848
2DNP 0R drive releaseResistor_SMD:R_0603_1608MetricR870, R871
110.2k 0.1% 25ppm current limitResistor_SMD:R_0603_1608MetricR2270
1100R BAT input filterResistor_SMD:R_0603_1608MetricR840
1100R SRN filterResistor_SMD:R_0603_1608MetricR846
1100R SRP filterResistor_SMD:R_0603_1608MetricR845
1100k 180..420ms current holdResistor_SMD:R_0603_1608MetricR2277
1100k UVLO topResistor_SMD:R_0603_1608MetricR884
1100k control health default-lowResistor_SMD:R_0603_1608MetricR2255
1100k current reset pull-upResistor_SMD:R_0603_1608MetricR2276
1100k current-ready default-lowResistor_SMD:R_0603_1608MetricR2275
1100k permission default-lowResistor_SMD:R_0603_1608MetricR2278
1100k raw health default-lowResistor_SMD:R_0603_1608MetricR2251
1100k reset default-lowResistor_SMD:R_0603_1608MetricR882
1100k startup fault pull-upResistor_SMD:R_0603_1608MetricR889
1100k startup permit gate seriesResistor_SMD:R_0603_1608MetricR894
1100k startup shutdown topResistor_SMD:R_0603_1608MetricR892
1100k thermal charge-health pull-upResistor_SMD:R_0603_1608MetricR2230
1100k thermal discharge-health pull-upResistor_SMD:R_0603_1608MetricR2231
1100n 25V C0G startup rampCapacitor_SMD:C_1206_3216MetricC882
1100n 50V OFF-bias bypassCapacitor_SMD:C_0603_1608MetricC2232
1100n 50V bus buffer supplyCapacitor_SMD:C_0603_1608MetricC2252
1100n 50V current supervisor supplyCapacitor_SMD:C_0603_1608MetricC2278
1100n 50V differential current filterCapacitor_SMD:C_0603_1608MetricC846
1100n 50V readiness buffer supplyCapacitor_SMD:C_0603_1608MetricC2253
1100n 50V readiness logic supplyCapacitor_SMD:C_0603_1608MetricC2279
1100n 50V reference outputCapacitor_SMD:C_0603_1608MetricC2280
1100n 50V thermal buffer supplyCapacitor_SMD:C_0603_1608MetricC2231
1100n 50V thermal regulator inputCapacitor_SMD:C_0603_1608MetricC2200
1100n 50V thermal supervisor supplyCapacitor_SMD:C_0603_1608MetricC2230
110A fast pack fuseducktop2:Schurter_HCF_8.05x5mmF1
110k 0.1% 25ppm NTC sense-lead limitResistor_SMD:R_0402_1005MetricR2217
110k LD senseResistor_SMD:R_0603_1608MetricR852
110k PACK senseResistor_SMD:R_0603_1608MetricR851
110k TS1 terminationResistor_SMD:R_0603_1608MetricR883
110k current-ready pull-upResistor_SMD:R_0603_1608MetricR2274
110n 50V thermal reference filterCapacitor_SMD:C_0402_1005MetricC2243
110u 25V REGIN; effective >=2uCapacitor_SMD:C_0805_2012MetricC881
110u 50V thermal bias; require Ceff >=2uCapacitor_SMD:C_1206_3216MetricC2201
112k 0.1% 25ppm ILIMResistor_SMD:R_0603_1608MetricR887
1147k 0.1% 25ppm DSG_COLD topResistor_SMD:R_0603_1608MetricR2244
116.9k 0.1% 25ppm current limitResistor_SMD:R_0603_1608MetricR2272
11M thermal-ready default-lowResistor_SMD:R_0603_1608MetricR2233
11M translator gate-sourceResistor_SMD:R_0603_1608MetricR891
11k 1% 0.75W raw thermal supply limiterResistor_SMD:R_2010_5025MetricR2200
11k PDSG translator gateResistor_SMD:R_0603_1608MetricR890
11u 10V REG18Capacitor_SMD:C_0603_1608MetricC841
11u 10V control inputCapacitor_SMD:C_0603_1608MetricC2257
11u 10V control outputCapacitor_SMD:C_0603_1608MetricC2258
11u 10V reference inputCapacitor_SMD:C_0603_1608MetricC2272
11u 10V reference outputCapacitor_SMD:C_0603_1608MetricC2273
11u 25V BAT supplyCapacitor_SMD:C_0603_1608MetricC840
11u 50V REGIN inputCapacitor_SMD:C_0805_2012MetricC880
11u 50V startup inputCapacitor_SMD:C_0805_2012MetricC883
11u 50V thermal switch inputCapacitor_SMD:C_0805_2012MetricC2281
1220n 50V startup output; effective >=100nCapacitor_SMD:C_0603_1608MetricC884

The 121 most common of 201 parts.

More from EwoudVV/ducktop2

6
  • 8 layers358 × 185 mmMonolith ducktop2, the printed circuit board in 3D

    Monolith ducktop2

    EwoudVV/ducktop2

    An open-source 16-inch laptop designed from scratch.

    1,225 parts26MIT
  • 8 layers227 × 185 mmDucktop2-center, the printed circuit board in 3D

    Ducktop2-center

    EwoudVV/ducktop2

    An open-source 16-inch laptop designed from scratch.

    870 parts26MIT
  • 8 layers70 × 185 mmLeft io, the printed circuit board in 3D

    Left io

    EwoudVV/ducktop2

    An open-source 16-inch laptop designed from scratch.

    334 parts26MIT
  • 4 layers273.5 × 80 mm12 keyboard daughterboard, the printed circuit board in 3D

    12 keyboard daughterboard

    EwoudVV/ducktop2

    An open-source 16-inch laptop designed from scratch.

    221 parts26MIT
  • 8 layers58 × 117 mmRight io, the printed circuit board in 3D

    Right io

    EwoudVV/ducktop2

    An open-source 16-inch laptop designed from scratch.

    174 parts26MIT
  • 4 layers120 × 70 mmRadio daughterboard, the printed circuit board in 3D

    Radio daughterboard

    EwoudVV/ducktop2

    An open-source 16-inch laptop designed from scratch.

    126 parts26MIT

Similar boards

  • 4 layers46.4 × 99.8 mmTrimix Analyzer, the printed circuit board in 3D

    Trimix Analyzer

    magnus188/aegir

    Open-source ESP32-P4 trimix analyzer prototype for technical diving,

    171 parts14
  • 4 layers116 × 112 mmBldc esc, the printed circuit board in 3D

    Bldc esc

    EwoudVV/bldc-esc

    A custom STM32 motor controller for BLDC and PMSM motors.

    453 parts2
  • 2 layers180 × 140 mmSliver only, the printed circuit board in 3D

    Sliver only

    DD1SB/ARDF-TX

    Date: 2026-10-15. Engineering review only; unbuilt and unenergized. Open RF80.kicadpro, schematic and native PCB in KiCad10.0.6. Three primary PCBs and the separate VHF true-AM design are unchanged.

    326 partsMIT
  • 4 layers59 × 101 mmEnku mainboard r0.1, the printed circuit board in 3D

    Enku mainboard r0.1

    aliaksei-lameyka/ENKU-Base-reader

    Open enku-mainboard-r0.1.kicadpro with KiCad10.0.7. Matching PCB/root schematic and power.kicadsch, mcuio.kicadsch, epdhv.kicadsch, connectors.kicadsch are canonical.

    127 parts1CERN-OHL-W-2.0
  • 2 layers139 × 45 mmSoil Power Sensor, the printed circuit board in 3D

    Soil Power Sensor

    jlab-sensing/ENTS-node-hardware

    Schematics and design for soil MFC voltage and current sensing

    72 parts
  • 4 layers220 × 120 mmCandidate filled profile, the printed circuit board in 3D

    Candidate filled profile

    misko/prompt2device

    The separate vNext PCB skill and orchestrator package is available alongside the reference workflow below; existing projects keep their accepted toolchain until an explicit migration.

    569 parts3MIT
  • 4 layers191.5 × 121.8 mmFoxhunt1, the printed circuit board in 3D

    Foxhunt1

    gx1400/kicad_foxhunt_batterytest

    Custom amateur radio fox hunt (hidden transmitter) controller, aimed at being a flexible, dynamic platform for a wide range of fox-hunt formats — not just a fixed single-mode beacon.

    260 parts
  • 4 layers165 × 100 mmUsb scoring platform, the printed circuit board in 3D

    Usb scoring platform

    AndrewCraswell/agency

    Native KiCad engineering prototype, separate from the earlier ESP32/tscircuit board. Open usb-scoring-platform.kicadpro in KiCad 10; schematic and PCB are the editable source, with no generator required.

    224 partsMIT

Questions

How big is the Bms PCB?

It measures 80 × 36.1 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Bms use?

201 parts, built around the RT0603BRD07499KL, RT0603BRD07100KL, RT0603BRD0710KL and RC0603FR-07100KL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Bms KiCad files?

From the EwoudVV/ducktop2 repository on GitHub, at the commit this page was made from: the board is bms/bms.kicad_pcb and its schematic 01_power_battery.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Bms design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).