Skip to the content
4 layers96 × 258.2 mmWidaq magis ssr v2b, the printed circuit board in 3D

Widaq magis ssr v2b

ejangelico/SSRTeensy1

The teensy code for the teensy SSR controller.

Size
96 × 258.2 mm
Copper layers
4
Thickness
1.6 mm
Parts
55
Nets
185
Pads
622
Tracks, vias
624, 17
Pours
6
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
9 Sep 2021
Updated
8 Sep 2026

Overview

Widaq magis ssr v2b is an open-source printed circuit board by ejangelico, from the ejangelico/SSRTeensy repository on GitHub. It is a 4-layer board of 96 × 258.2 mm with 55 parts on 185 nets, routed with 624 tracks and 17 vias.

It is built around the SN74AHCT125PW. Its parts include 16 ICs, 9 resistors, 7 capacitors, 2 switches and 1 diode. It belongs with the NXP (LPC, Kinetis, i.MX RT) boards of this library.

Main components

1

README

README.md

SSRTeensy

Libraries

Arduino 1.8.15 Teensydino 1.54

Communication interface guide (documentation in progress)

There are 16 pulse width modulation (PWM) channels active and available for functions related to setting the temperature of heaters using solid state relays and thermocouple feedback. Each of the channels initializes an "SSRController" object. The object contains a state enumerator for the presently active function of the channel. This section describes how to interface with each channel by sending messages over a serial connection.

Available commands

The general structure of a message to the Teensy is in the following form: #<ch>:<command>=<arg1>,<arg2>,<arg3>,<arg4>,<arg5> .

Depending on the command type, there may be a different number of required arguments, and argument parsing stops once the required arguments are parsed. Commands are their arguments are described in the below list.

  • TEMP_SET : command subset for changing the SSR duty cycles to match a setpoint temperature or manual input
    • POWER_OFF : turn SSR relays to 0 duty cycle
      • #3:TEMP_SET=POWER_OFF,,,
    • RAMP : linear ramp in temperature up to a setpoint
    • CONST : reach a constant temperature (with no controlled slope ramp) and hold at that temperature
    • MANUAL : manually set the duty cycle of SSRs to some fraction from 0% to 100%
      • #3:TEMP_SET=MANUAL,<duty cycle 0 to 100>,,,, #3:TEMP_SET=MANUAL,43.5,,,
  • TEMP_CUR : provide the Teenys with information about the present temperature associated with a particular SSR channel; this is feedback for a PID loop or any of the TEMP_SET functions
    • #<ch>:TEMP_CUR=<temp in C>,<timestamp>, #3:TEMP_CUR=32.5,1656444270
  • PIDP_SET : set the P, I, and D parameters for the PID control equation

To do for devs

  • We want to change the ramp functionality inputs so that the UI just presses "start" or "stop" and the linear ramp curve is executed automatically (no timing arguments). Target temp and ramp rate are still args, but even ramp rate can have a default of 1 C/min.

Parts

55
QtyValueFootprintReferences
16SN74AHCT125PWPackage_DIP:DIP-14_W7.62mmU1, U2, U3, U4, U7, U8, U9, U10, U12, U13, U14, U15, U17, U18, U19, U20
41 nFCapacitor_THT:C_Disc_D4.3mm_W1.9mm_P5.00mmC1, C5, C6, C7
41kResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_HorizontalR4, R6, R8, R10
42kResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_HorizontalR3, R5, R7, R9
4HC06Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalHC1, HC2, HC3, HC4
4Teensy4.0teensy:Teensy40Teen1, Teen2, Teen3, Teen4
4dsub-37-to-ribbonteensy:TYCO_5103309-7-fordsub37DSUB1, DSUB2, DSUB3, DSUB4
10Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1
110 nFCapacitor_THT:C_Disc_D4.3mm_W1.9mm_P5.00mmC4
1100 nFCapacitor_THT:C_Disc_D4.3mm_W1.9mm_P5.00mmC3
11uFCapacitor_THT:C_Disc_D4.3mm_W1.9mm_P5.00mmC2
12169900003teensy:MOLEX_2169900003J1
12A Fuse teensy:LittleFuseHolderF2
1Jumper_2_OpenConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJP1
1LEDConnector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_HorizontalD1
1LOGOlogos:magis-logo-1inchG***
1MountingHole_PadMountingHole:MountingHole_3.7mm_Pad_ViaH1
1SW_DIP_x01Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_HorizontalSW1
1SW_Push_OpenConnector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_HorizontalSW2

The 52 most common of 55 parts.

More from ejangelico/SSRTeensy

2
  • 4 layers100 × 95.5 mmV2a power board-4, the printed circuit board in 3D

    V2a power board-4

    ejangelico/SSRTeensy

    The teensy code for the teensy SSR controller.

    30 parts1
  • 2 layers72.3 × 95.5 mmV2a power board, the printed circuit board in 3D

    V2a power board

    ejangelico/SSRTeensy

    The teensy code for the teensy SSR controller.

    25 parts1

Similar boards

  • 2 layers52.9 × 87.4 mmWled, the printed circuit board in 3D

    Wled

    KamilJurczenko/WLED_Controller

    My first designed pcb board to control some LEDs.

    15 partsMIT
  • 4 layers97 × 94 mmMain PCB, the printed circuit board in 3D

    Main PCB

    root670/dance-pad

    Dance pad using FSRs and RGB LEDs in an extruded aluminum frame.

    20 parts13MIT
  • 4 layers50 × 30 mmPicodvi, the printed circuit board in 3D

    Picodvi

    Fr4nkFletcher/ESP32-Marauder-Cheap-Yellow-Display

    ESP32Marauder Cheap Yellow Display

    55 parts1.8kMIT
  • 4 layers43 × 49 mmEsppdp, the printed circuit board in 3D

    Esppdp

    Spritetm/esppdp

    ESP32-based PDP11 simulator, based onSimH

    55 parts141
  • 4 layers37 × 34.3 mmReadout 60pin, the printed circuit board in 3D

    Readout 60pin

    opentac/opentac

    OpenTac: open tools to design, fabricate, read and simulate flex-PCB tactile skins that sense normal and shear force, for any robot surface.

    55 parts92MIT
  • 4 layers13 × 9.4 mmTomu fpga, the printed circuit board in 3D

    Tomu fpga

    AlexeyInwerp/BoardRipper

    Web-based PCB boardview viewer for board-level repair. 14 formats: BVR1/3, BRD, BDV, BDV ASC, FZ, GenCAD, Mentor Neutral, XZZ, TVW, Allegro v15-v18, Altium, KiCad, EAGLE.

    55 parts48AGPL-3.0
  • 4 layers119 × 73.9 mmFw16 oculink8i, the printed circuit board in 3D

    Fw16 oculink8i

    Terrails/FW16-OCuLink

    The schematic in itself is pretty simple. You only need to connect the TX and RX PCIe lanes to the correct pins of the OCuLink connector.

    55 parts43MIT
  • 4 layers65 × 50 mmUsbbase, the printed circuit board in 3D

    Usbbase

    daveshah1/openMixR

    4k Mixed Reality headset

    55 parts40MIT

Questions

How big is the Widaq magis ssr v2b PCB?

It measures 96 × 258.2 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Widaq magis ssr v2b use?

55 parts, built around the SN74AHCT125PW. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Widaq magis ssr v2b KiCad files?

From the ejangelico/SSRTeensy repository on GitHub, at the commit this page was made from: the board is widaq-magis-ssr-v2b/widaq-magis-ssr-v2b.kicad_pcb and its schematic widaq-magis-ssr-v2b/i2c_block.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Widaq magis ssr v2b design in my own project?

Its repository states no licence, so its author keeps all rights: ask ejangelico before reusing the design.