
Le oeuf
eggsworks/le-oeuf-v2
An ultra-low profile (Kailh PG1316S) keyboard inspired by Le Chiffre.

Int brain pcb is an open-source printed circuit board by eccentricOrange, from the eccentricOrange/int-brain-stm32 repository on GitHub. It is a 4-layer board of 170.2 × 79 mm with 217 parts on 265 nets, routed with 2,402 tracks and 781 vias.
It is built around the MCP2561-E/SN, TPS5450DDAR and AMS1117-1.8, with the AMS1117-3.3, ICM-20948 and CC0603KRX7R9BB104 among its other parts. Its parts include 74 capacitors, 70 resistors, 19 connectors, 17 diodes and 10 ICs.
| Configuration | Setting | Description |
|---|---|---|
| PMODE | 10k pull-down | Sets to PH/EN mode |
| R-propi | 1.222kΩ | 6A corresponds to 3.3V |
| V-ref | 2.16V | Current limit set to 4A |
| R-Imode | Disconnected | Fixed off-time current limiting |
| nFAULT | Pulled up to 3.3V | - |
| Purpose | STM32 | ST-Link | Ribbon cable |
|---|---|---|---|
| SWDIO | PA13 | SWDIO | 2 |
| SWCLK | PA14 | SWCLK | 6 |
| JTDI | PA15 | (not used) | - |
| JTDO | PB3 | SWO | 4 |
| JNTRST | PB4 | (not used) | 5 |
| 5 V | 5 V | 5 V | 9, 10 |
| VDD | 3.3 V | 3.3 V | 7, 8 |
| GND | GND | GND | 3, 4 |
| Device | Peripheral | GPIO | Function | Notes |
|---|---|---|---|---|
| USB | USB | A11 A12 | D- D+ | - |
| SBC | I2C1 | B6 B7 | SDA SCL | 3V3 4K7 PUR |
| IMU USBPD | I2C2 EXTI13 EXTI14 | B11 B12 B13 B14 | SDA SCL INT-E INT-I | 3V3 4K7 PUR |
| SBC | USART2 | D5 D6 | TX RX | - |
| SBC | USART3 | D8 D9 | TX RX | - |
| CAN | CAN1 | B8 B9 | RX TX | TERM 120R |
| Peripheral | GPIO | Function |
|---|---|---|
| BUTTON0 | A0 | WKUP |
| LED0 | A3 | TIM5.3 |
| DRV_OFF | B0 | - |
| VBATT | C4 | ADC2_IN14 |
| Motor | Phase | Enable | Encoder A | Encoder B | Current sense ADC |
|---|---|---|---|---|---|
| 1 | C11 TIM3.1 | C6 | E5 TIM9.1 | E6 TIM9.2 | C0 ADC1_IN10 |
| 2 | C12 TIM3.2 | C7 | A8 TIM1.1 | A9 TIM1.2 | C1 ADC1_IN11 |
| 3 | C13 TIM3.3 | C8 | A1 TIM2.2 | A2 TIM2.3 | C2 ADC1_IN12 |
| 4 | C14 TIM3.4 | C9 | D12 TIM4.1 | D13 TIM4.2 | C3 ADC1_IN13 |
| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 100nF | Capacitor_SMD:C_0402_1005Metric | C28, C29, C30, C31, C32, C34, C35, C37, C38, C73, C74, C75, C76, C77 |
| 9 | 100nF | Capacitor_SMD:C_0603_1608Metric | C25, C40, C41, C44, C45, C48, C49, C52, C53 |
| 8 | 2.2nF | Capacitor_SMD:C_1206_3216Metric | C55, C56, C57, C58, C59, C60, C61, C62 |
| 8 | 3.3k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R48, R49, R50, R51, R52, R53, R54, R55 |
| 8 | 470R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R29, R35, R41, R47, R56, R57, R58, R59 |
| 6 | 10nF | Capacitor_SMD:C_0805_2012Metric | C9, C10, C12, C18, C19, C21 |
| 5 | 4.7k | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1, R2, R8, R9, R14 |
| 5 | FAULT | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D11, D12, D13, D14, D19 |
| 4 | 1.2k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R26, R32, R38, R44 |
| 4 | 10k | Resistor_SMD:R_0402_1005Metric | R22, R64, R66, R67 |
| 4 | 10k | Resistor_SMD:R_1206_3216Metric | R7, R10, R16, R18 |
| 4 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R28, R34, R40, R46 |
| 4 | 10k | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R24, R30, R36, R42 |
| 4 | 10k | Resistor_SMD:R_0805_2012Metric | R27, R33, R39, R45 |
| 4 | 10nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C3, C4, C5 |
| 4 | 10uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C6, C14, C15 |
| 4 | 22nF | Capacitor_SMD:C_0603_1608Metric | C42, C46, C50, C54 |
| 4 | 4.7uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C7, C8, C16, C17 |
| 4 | 470uF | Capacitor_SMD:CP_Elec_10x12.5 | C39, C43, C47, C51 |
| 4 | 5.27k | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R25, R31, R37, R43 |
| 4 | DRV8874PWPR | Package_SO:HTSSOP-16-1EP_4.4x5mm_P0.65mm_EP3.4x5mm_Mask3x3mm_ThermalVias | U6, U7, U8, U9 |
| 4 | ENCODER | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J18, J19, J20, J21 |
| 4 | M3 | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1, H2, H3, H4 |
| 4 | MOTOR1 | Connector_JST:JST_PH_S6B-PH-K_1x06_P2.00mm_Horizontal | J22, J23, J24, J25 |
| 4 | RUN | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D15, D16, D17, D18 |
| 3 | 10uF | Capacitor_SMD:C_0603_1608Metric | C63, C71, C72 |
| 3 | 1k | Resistor_SMD:R_0402_1005Metric | R12, R71, R74 |
| 3 | 1uF | Capacitor_SMD:C_0402_1005Metric | C64, C65, C66 |
| 3 | SS56B | Diode_SMD:D_SMA-SMB_Universal_Handsoldering | D3, D5, D8 |
| 2 | 100R | Inductor_SMD:L_1206_3216Metric_Pad1.42x1.75mm_HandSolder | FB1, FB2 |
| 2 | 2.2uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C26, C27 |
| 2 | 20pF | Capacitor_SMD:C_0402_1005Metric | C23, C24 |
| 2 | 22uH | Inductor_SMD:L_Chilisin_BMRF00131350 | L1, L2 |
| 2 | 3.16k | Resistor_SMD:R_1206_3216Metric | R11, R17 |
| 2 | 330uF | Capacitor_Tantalum_SMD:CP_EIA-7343-15_Kemet-W_Pad2.25x2.55mm_HandSolder | C11, C20 |
| 2 | 390R | Resistor_SMD:R_0402_1005Metric | R62, R73 |
| 2 | SS54 | Diode_SMD:D_SMA_Handsoldering | D2, D10 |
| 2 | TPS5450DDA | Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm_ThermalVias | U1, U3 |
| 1 | 0R | Resistor_SMD:R_0402_1005Metric | R20 |
| 1 | 100R | Resistor_SMD:R_0402_1005Metric | R61 |
| 1 | 100nF | Capacitor_SMD:C_1206_3216Metric | C22 |
| 1 | 10m | Resistor_SMD:R_1206_3216Metric | R60 |
| 1 | 10uF | Capacitor_Tantalum_SMD:CP_EIA-3216-10_Kemet-I_Pad1.58x1.35mm_HandSolder | C33 |
| 1 | 120L | Inductor_SMD:L_0603_1608Metric | L3 |
| 1 | 120R | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R19 |
| 1 | 16k | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | 1uF | Capacitor_Tantalum_SMD:CP_EIA-3216-10_Kemet-I_Pad1.58x1.35mm_HandSolder | C36 |
| 1 | 2.2k | Resistor_SMD:R_1206_3216Metric | R15 |
| 1 | 220R | Resistor_SMD:R_0402_1005Metric | R21 |
| 1 | 220R | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R6 |
| 1 | 220R | Resistor_SMD:R_1206_3216Metric | R13 |
| 1 | 3.3k | Resistor_SMD:R_0402_1005Metric | R72 |
| 1 | 33nF | Capacitor_SMD:C_0402_1005Metric | C67 |
| 1 | 470uF | Capacitor_SMD:CP_Elec_6.3x7.7 | C13 |
| 1 | 47R | Resistor_SMD:R_0603_1608Metric | R23 |
| 1 | 47k | Resistor_SMD:R_0402_1005Metric | R63 |
| 1 | 47k | Resistor_SMD:R_0805_2012Metric | R3 |
| 1 | 7.5k | Resistor_SMD:R_0402_1005Metric | R5 |
| 1 | 8MHz | Crystal:Crystal_HC49-4H_Vertical | Y1 |
| 1 | AMS1117-1.8 | Package_TO_SOT_SMD:SOT-89-3 | U15 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | BUTTON0 | Button_Switch_THT:SW_PUSH_6mm | SW1 |
| 1 | CAN | Connector_USB:USB_C_Receptacle_Amphenol_12401610E4-2A | J8 |
| 1 | CAN | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J2 |
| 1 | GPS UART | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J1 |
| 1 | ICM-20948 | Sensor_Motion:InvenSense_QFN-24_3x3mm_P0.4mm | U13 |
| 1 | IMU | Connector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J4 |
| 1 | LED0 | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D1 |
| 1 | LOGIC PWR | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D7 |
| 1 | M1 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_Horizontal | J14 |
| 1 | M2 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_Horizontal | J15 |
| 1 | M3 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_Horizontal | J16 |
| 1 | M4 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_Horizontal | J17 |
| 1 | MCP2561-E-SN | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | MOTOR PWR | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D9 |
| 1 | MOTOR_PWR | dpdt-onoff-switch:SW_PUSH_6mm_H5mm | SW2 |
| 1 | NRST | Button_Switch_THT:SW_PUSH_6mm | SW3 |
| 1 | P1 | Connector_PinHeader_2.54mm:PinHeader_2x25_P2.54mm_Vertical | J12 |
| 1 | P2 | Connector_PinHeader_2.54mm:PinHeader_2x25_P2.54mm_Vertical | J13 |
| 1 | PC | Connector_USB:USB_C_Receptacle_Amphenol_12401610E4-2A | J7 |
The 203 most common of 217 parts.

eggsworks/le-oeuf-v2
An ultra-low profile (Kailh PG1316S) keyboard inspired by Le Chiffre.


Ndambia/lilygo
A custom 4-layer KiCad PCB design integrating an ESP32 Wi-Fi/Bluetooth microcontroller with a SIM7600G-H 4G LTE Cat-4 cellular module, comprehensive power management, GPS tracking, GPRS connectivity, USB-C charging…


bebenlebricolo/BTS-MainBoard-Power
Beer thermoregulation system mainboard - power section

bornier-dev/bornier
Open source EtherCAT slaves for machine tools running LinuxCNC: hardware, firmware and tooling.

Panda-Intelligence/panda-standard-board
The current product is the Panda Standard 4.7-inch parallel E0470A01-family single-board engineering design, with a replaceable 2050mAh LCO battery pack (323576) and a finished-device maximum thickness of 7mm, including…

It measures 170.2 × 79 mm and has 4 copper layers, 1.61 mm thick.
217 parts, built around the MCP2561-E/SN, TPS5450DDAR, AMS1117-1.8 and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the eccentricOrange/int-brain-stm32 repository on GitHub, at the commit this page was made from: the board is int-brain-stm32-pcb/int-brain-pcb.kicad_pcb and its schematic int-brain-stm32-pcb/encoder.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask eccentricOrange before reusing the design.