Skip to the content
2 layers69.6 × 80.5 mmProtoBoard, the printed circuit board in 3D

Repository for Kicad board development and support libraries

Size
69.6 × 80.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
158
Nets
98
Pads
461
Tracks, vias
1,354, 184
Pours
2
Routed
Yes
KiCad
KiCad 4
Created
10 Apr 2015
Updated
28 Jun 2015

Overview

ProtoBoard is an open-source printed circuit board by dustinreynolds, from the dustinreynolds/STM32Hardware repository on GitHub. It is a 2-layer board of 69.6 × 80.5 mm with 158 parts on 98 nets, routed with 1,354 tracks and 184 vias.

It is built around the ATSHA204A, RFM69HW and BSS123-7-F-VB, with the MS 2 and TQ2SA-3V among its other parts. Its parts include 56 resistors, 52 connectors, 12 capacitors, 7 ICs and 5 diodes.

Main components

5

README

README.md

STM32Hardware

Repository for Kicad board development and support libraries

This repository was created on Windows using Kicad built from source using kicad-winbuilder3.4.

Folder Hierarchy

  • Calculations - Brief calculations performed
  • kicad_lib - Libraries created for new schematic or pcb objects
  • Nucleo_L152RE - contains board designs that have been designed using Kicad build on 2015-05-11 from BZR commit 5650.

Hardware Releases

So far none of the designs in this repository have been tested and verified to be working. Footprints have been aligned with the actual components, but until the actual PCB's and the remaining components arrive, this repository should serve as a reference only. This readme will be updated to reflect the latest testing status.

ProtoBoard Rev AA had the following issues: Using 5 pins from morpheo headers that didn't have a pin on them. RFM69HW footprint was backwards for part of it. See AA schematics for additional notes.

Protoboard Rev AB made the following changes: Removed USB, replaced with low voltage relay and fet Added Crypto chip ATSHA204A to i2c bus Added GPS to I2C bus (those same pins can be used as USART) Split schematic into 5 pages to ease readability Added 5V in and use that as main power input signal (this leaves programmer unpowered) Added additional voltage sense pins on 5V connector for monitoring state of battery pack Added 3.3V regulator that can be controlled via enable pin. This is so SPI/I2C/OneWire devices can be powered off easily. On board chips have low power requirements when asleep. Added additional spare Gnd, 3.3V, 3.3Vctl, and 5.0V lines for expansion. Added Servo power input for motionsense 1 and 2 (which are also pwm pins) Added piezo buzzer on OneWire3 Added CS pin for RGB connector since it can be a spare SPI Removed mounting holes since this is securely mounted to Nucleo board.

Parts

158
QtyValueFootprintReferences
230Resistors_SMD:R_0603_HandSolderingR1, R2, R3, R5, R23, R24, R26, R35, R40, R42, R44, R45, R46, R49, R50, R52 +7
12GNDPin_Headers:Pin_Header_Straight_1x01P7, P8, P9, P10, P11, P12, P13, P14, P15, P16, P17, P18
11Jumper_NC_Smallnucleo:SB_NO_SmallerJP1, JP2, JP3, JP4, JP5, JP10, JP12, JP14, JP15, JP16, JP17
60.1uCapacitors_SMD:C_0603C7, C8, C9, C10, C11, C12
6220Resistors_SMD:R_0603_HandSolderingR19, R20, R21, R22, R38, R51
6tpnucleo:TestPoint_1mmTP1, TP2, TP3, TP4, TP5, TP6
42.2kResistors_SMD:R_0603_HandSolderingR29, R30, R32, R33
30.1uCapacitors_SMD:C_0603_HandSolderingC4, C5, C6
3100kResistors_SMD:R_0603_HandSolderingR43, R47, R48
31kResistors_SMD:R_0603_HandSolderingR16, R17, R18
33.3CtlPin_Headers:Pin_Header_Straight_1x01P19, P20, P21
33.3VPin_Headers:Pin_Header_Straight_1x01P22, P23, P24
34.7kResistors_SMD:R_0603_HandSolderingR28, R39, R41
35.0VPin_Headers:Pin_Header_Straight_1x01P25, P26, P27
3976k 1%Resistors_SMD:R_0603_HandSolderingR10, R11, R12
210kResistors_SMD:R_0603_HandSolderingR25, R27
21KResistors_SMD:R_0603_HandSolderingR4, R15
21uCapacitors_SMD:C_0603_HandSolderingC1, C3
2332k 1%Resistors_SMD:R_0603_HandSolderingR13, R14
2BSS123-7-Fnucleo:SOT23-3Q1, Q2
2Jumper_NO_Smallnucleo:SB_NO_SmallerJP11, JP13
2Rednucleo:LED_0603_StandardD1, D4
2WS2Pin_Headers:Pin_Header_Straight_1x03P56, P57
110nCapacitors_SMD:C_0603_HandSolderingC2
12.2KResistors_SMD:R_0603_HandSolderingR34
13.6M 1%Resistors_SMD:R_0603_HandSolderingR9
1390Resistors_SMD:R_0603_HandSolderingR37
14.7KResistors_SMD:R_0603_HandSolderingR31
1680Resistors_SMD:R_0603_HandSolderingR36
1ATSHA204Anucleo:8-SOIC-JEDEC_MS-012AAU7
1Antnucleo:Antenna_1pinP55
1Bluenucleo:LED_0603_StandardD3
1EXTnucleo:RJ45_SMDJ2
1EXTPowernucleo:RJ45_SMDJ1
1FET_SW1Pin_Headers:Pin_Header_Straight_1x03P51
1GND1Pin_Headers:Pin_Header_Straight_1x02P5
1GND2Pin_Headers:Pin_Header_Straight_1x02P6
1Greennucleo:LED_0603_StandardD2
1I2C1_APin_Headers:Pin_Header_Straight_1x04P46
1I2C1_BPin_Headers:Pin_Header_Straight_1x04P49
1I2C2_APin_Headers:Pin_Header_Straight_1x04P47
1I2C2_BPin_Headers:Pin_Header_Straight_1x04P50
1LDS3985nucleo:SOT23-5LU1
1MS1Pin_Headers:Pin_Header_Straight_1x03P40
1MS2Pin_Headers:Pin_Header_Straight_1x03P42
1MS3Pin_Headers:Pin_Header_Straight_1x03P41
1MS4Pin_Headers:Pin_Header_Straight_1x03P43
1MT3329_GPSnucleo:MT3329_LessPinsU5
1MomentarySwitchnucleo:Tact_switchSW1
1Nucleo-L152RE-CN10Pin_Headers:Pin_Header_Straight_2x19U3
1Nucleo-L152RE-CN7Pin_Headers:Pin_Header_Straight_2x19U2
1OSHW SymbolSymbols:Symbol_OSHW-Logo_SilkScreenS1
1OW1_APin_Headers:Pin_Header_Straight_1x03P45
1OW2_APin_Headers:Pin_Header_Straight_1x03P53
1OW3_APin_Headers:Pin_Header_Straight_1x03P54
1Piezonucleo:Piezo_12mmB1
1Power1Pin_Headers:Pin_Header_Straight_1x04P35
1Power2Pin_Headers:Pin_Header_Straight_1x02P31
1RFM69HWnucleo:RFM69HW_LessPinsU6
1RGB1Pin_Headers:Pin_Header_Straight_1x06P38
1RLY1Pin_Headers:Pin_Header_Straight_1x03P44
1RLY2Pin_Headers:Pin_Header_Straight_1x03P48
1ResetSwitchnucleo:Tact_switchSW2
1S25FL127Snucleo:SOIC-8-FLASHU4
1SWBUS1Pin_Headers:Pin_Header_Straight_2x06P32
1SWD HeaderPin_Headers:Pin_Header_Straight_1x06P37
1ServoPowerPin_Headers:Pin_Header_Straight_1x02P34
1TQ2SA-3Vnucleo:Relay_SMDRLY1
1USART1Pin_Headers:Pin_Header_Straight_1x04P39
1USART2Pin_Headers:Pin_Header_Straight_1x04P36
1VinPowerPin_Headers:Pin_Header_Straight_1x02P33
1WS1Pin_Headers:Pin_Header_Straight_1x03P52
1Yellownucleo:LED_0603_StandardD5

More from dustinreynolds/STM32Hardware

1
  • 2 layers68.6 × 80.5 mmProtoBoard, the printed circuit board in 3D

    ProtoBoard

    dustinreynolds/STM32Hardware

    Repository for Kicad board development and support libraries

    116 parts2

Similar boards

  • 2 layers50 × 50 mmMysensorsGW, the printed circuit board in 3D

    MysensorsGW

    mysensors/SensebenderGW

    Gateway for MySensors

    76 parts7
  • 2 layers55 × 35 mmMini BT Pcb-328P, the printed circuit board in 3D

    Mini BT Pcb-328P

    d-diot/Mini-BT-Pcb-328P

    MySensors ATMega328P + RFM69 and NRF24 battery (AAA and CR2032) powered pcb

    54 parts3
  • 2 layers68.6 × 53.3 mmMyGateway, the printed circuit board in 3D

    MyGateway

    ger-ator/MyGateway

    RFM69 + ATSHA204A Shield for Arduino.

    24 partsGPL-3.0
  • 2 layers50 × 49.9 mmEasyPCB 10 RFM69hw, the printed circuit board in 3D

    EasyPCB 10 RFM69hw

    sundberg84/HomeAutomation

    Everything from sundberg84 homeautomation - mostly for backup!

    37 parts5
  • 2 layers58.5 × 88 mmFugu2, the printed circuit board in 3D

    Fugu2

    fl4p/Fugu2

    Links: git | kicanvas | cadlab | docs | pdf schematics | IBOM (TODO) | firmware | additional docs & resources

    147 parts24
  • 2 layers139 × 45 mmSoil Power Sensor, the printed circuit board in 3D

    Soil Power Sensor

    jlab-sensing/ENTS-node-hardware

    Schematics and design for soil MFC voltage and current sensing

    72 parts
  • 8 layers115.3 × 25.3 mmPROC091G, the printed circuit board in 3D

    PROC091G

    um-kiho/ti_radar

    AWR6843AOP (Antenna-on-Package) 60GHz FMCW 레이더를 이용한 존재 감지(Presence Detection) 시스템입니다. 내장 ARM Cortex-R4F MCU + C674x DSP에서 신호 처리 및 존재 판정을 수행하고, UART로 결과를 출력합니다.

    446 parts

Questions

How big is the ProtoBoard PCB?

It measures 69.6 × 80.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the ProtoBoard use?

158 parts, built around the ATSHA204A, RFM69HW, BSS123-7-F-VB and MS 2. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the ProtoBoard KiCad files?

From the dustinreynolds/STM32Hardware repository on GitHub, at the commit this page was made from: the board is Nucleo_L152RE/ProtoBoard/AB/ProtoBoard.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the ProtoBoard design in my own project?

Its repository states no licence, so its author keeps all rights: ask dustinreynolds before reusing the design.