Skip to the content
4 layers82.4 × 62.5 mmFluidnc bob, the printed circuit board in 3D

Open CNC control stack for a Sherline 2000: FluidNC ESP32-S3 breakout hardware + host software plan

Size
82.4 × 62.5 mm
Copper layers
4
Thickness
1.6 mm
Parts
49
Nets
63
Pads
168
Tracks, vias
205, 29
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
18 Jul 2026
Updated
6 Aug 2026

Overview

Fluidnc bob is an open-source printed circuit board by drewsipher, from the drewsipher/sharkcnc repository on GitHub. It is a 4-layer board of 82.4 × 62.5 mm with 49 parts on 63 nets, routed with 205 tracks and 29 vias.

It is built around the SN74HC541N, GS1A and 1210L150/16WR, with the MMBT2222A among its other parts. Its parts include 19 resistors, 7 capacitors, 4 diodes, 2 connectors and 1 IC. It belongs with the interfaces and adapters boards and the ESP32 boards of this library.

Main components

4

README

hardware/fluidnc-bob/README.md

fluidnc-bob rev C — ESP32-S3 FluidNC breakout (schematic + netlist)

FluidNC controller interface for the Sherline 2000 / FMD2740C drivers: socketed 44-pin dual-USB-C ESP32-S3-WROOM-1 (N16R8) devkit, SN74HC541N 5 V buffer (VCC dropped through a GS1A so 3.3 V inputs meet V_IH), filtered limit/probe inputs, microSD breakout header, spindle relay driver. All connections are solder wire pads — no connectors.

Deliverable = schematic + verified netlist + footprint assignments. Board layout is done by hand in KiCad ("Update PCB from Schematic" pulls in everything, including the custom footprints in fluidnc-bob.pretty/).

Design state: ERC clean (0 violations); netlist machine-verified against generate/design.py (generate/verify_netlist.py — partition and power-net comparison). Unbuilt, rev C.

⚠ Layout-time checklist

  1. MEASURE THE DEVKIT ROW SPACING. The socket footprint assumes 22.86 mm (0.9"); both 22.86 and 25.4 mm exist among 44-pin S3 boards. Set ROWSP in generate/gen_fp.py (or edit the footprint) to match, and check the devkit's printed pin legend against DEVKIT_LEFT/RIGHT in generate/design.py (pin 1 = 3V3, antenna end).
  2. N16R8 (octal PSRAM): GPIO 35/36/37 intentionally unconnected.
  3. U1's buffer channels are interchangeable — permute freely during routing.
  4. Keep the FMD2740C signal runs and logic ground away from motor power; single-point ground at the supply.
  5. Don't feed 5 V and devkit USB simultaneously unless the devkit's backfeed diode is verified.

Wire pad groups

RefPads (1 = square)Goes to
J15V, GND5 V PSU (through F1 polyfuse, D2 reverse crowbar)
J2STEP, DIR, GNDX driver: SP+, DIR+; GND wire bridges SP−+DIR−
J3STEP, DIR, GNDY driver
J4STEP, DIR, GNDZ driver
J5 / J6SIG, GNDX / Y limit switch (closes to GND)
J10 / J11SIG, GNDZ limit / probe
J7+5V, COIL−spindle relay coil (2N7000 low side, D1 flyback)
J8AUX, GNDspare buffered 5 V output
J9SCK, MISO, MOSI, CS, 5V, GNDmicroSD breakout (feed it 5 V; its 4050 + 3.3 V reg handle the rest)

GPIO map (ESP32-S3)

SignalGPIOSignalGPIO
X step / dir18 / 17X / Y / Z limit42 / 2 / 1
Y step / dir16 / 15Probe41
Z step / dir7 / 6SD SCK / MISO / MOSI / CS12 / 13 / 11 / 10
Spindle relay5Aux out4

Inputs: 10 k pullup to 3V3 + 1 k series + 100 nF on board.

FluidNC config

The maintained config is config.yaml (bench bring-up, as-built active-high step/dir; limits/probe are :low because the board pulls them up and switches close to GND). Verified against FluidNC v4.0.3 example syntax — note it is sdcard:, not sd:.

If the drivers are reworked to common-anode (SP+/DIR+ tied to +5V), add :low to every step_pin and direction_pin.

Upload jobs to SD and run locally — WiFi then carries only status/jog and can never stall a cut. Verify pin syntax against the FluidNC wiki for the S3 release you flash.

Regenerating / verifying

sh
python3 generate/gen_fp.py        # footprints (socket ROWSP lives here)
python3 generate/gen_sch.py       # schematic (drawn wires; self-checks)
kicad-cli sch erc --exit-code-violations fluidnc-bob.kicad_sch
python3 generate/verify_netlist.py  # diff KiCad netlist vs design.py

generate/design.py is the netlist source of truth. generate/gen_pcb.py is retired (the rev B auto-layout experiment) — kept for reference only; it no longer matches the current design.

Parts

49
QtyValueFootprintReferences
9100kResistor_SMD:R_0805_2012MetricR10, R11, R12, R13, R14, R15, R16, R17, R41
6100nFCapacitor_SMD:C_0805_2012MetricC2, C3, C20, C21, C22, C23
61kResistor_SMD:R_0805_2012MetricR30, R31, R32, R33, R40, R50
410kResistor_SMD:R_0805_2012MetricR20, R21, R22, R23
4MountingHoleMountingHole:MountingHole_3.2mm_M3H1, H2, H3, H4
3GS1ADiode_SMD:D_SMAD1, D2, D3
1100uFCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC1
11210L150/16WRFuse:Fuse_1210_3225MetricF1
15V-INfluidnc-bob:WirePads_1x02_P5.08mmJ1
1AUXfluidnc-bob:WirePads_1x02_P5.08mmAUX
1Conn_02x06_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x06_P2.54mm_VerticalJ13
1ESP32-S3-DevKit-44fluidnc-bob:ESP32_S3_DevKit_44_SocketA1
1LIM-Xfluidnc-bob:WirePads_1x02_P5.08mmXLIM
1LIM-Yfluidnc-bob:WirePads_1x02_P5.08mmYLIM
1LIM-Zfluidnc-bob:WirePads_1x02_P5.08mmZLIM
1MMBT2222APackage_TO_SOT_SMD:SOT-23Q1
1PROBEfluidnc-bob:WirePads_1x02_P5.08mmPROBE
1PWRLED_THT:LED_D5.0mmLED1
1RELAYfluidnc-bob:WirePads_1x02_P5.08mmRELAY
1SN74HC541NPackage_DIP:DIP-20_W7.62mm_SocketU1
1X-DRVfluidnc-bob:WirePads_1x03_P5.08mmX
1Y-DRVfluidnc-bob:WirePads_1x03_P5.08mmY
1Z-DRVfluidnc-bob:WirePads_1x03_P5.08mmZ

More from drewsipher/sharkcnc

1
  • 2 layers90.4 × 98.7 mmFluidnc bob revD, the printed circuit board in 3D

    Fluidnc bob revD

    drewsipher/sharkcnc

    Open CNC control stack for a Sherline 2000: FluidNC ESP32-S3 breakout hardware + host software plan

    66 parts

Similar boards

  • 4 layers72.4 × 44.4 mmBtmdpcb v04 eval, the printed circuit board in 3D

    Btmdpcb v04 eval

    17o2/bluetooth-minidisc

    Adding built-in bluetooth connectivity to a 20-year-old Mindisc player

    115 parts45
  • 4 layers127 × 76.2 mmPayload pcb, the printed circuit board in 3D

    Payload pcb

    austindriggs/urc-payload-pcb

    All-purpose control and interface board designed to manage mission-critical sensors and electronics for University Rover Challenge at WVU.

    114 partsMIT
  • 2 layers170 × 105 mmSsio check, the printed circuit board in 3D

    Ssio check

    paulbruneau/ssio-check

    A bench tester for the Bally/Midway MCR Sound I/O family: the 90908 Sound I/O and the 90913 / 91483 / 91657 Super Sound I/O (Z80, two AY-3-8910s, and all of the game's input ports).

    72 parts
  • 2 layers75 × 100 mmPhased, the printed circuit board in 3D

    Phased

    Neumi/open_echo

    Open Source echo sounder / depth sounder / SONAR for bathymetry and research. Arduino based and compatible.

    77 parts530
  • 2 layers80 × 129.1 mmSmart Plant, the printed circuit board in 3D

    Smart Plant

    JGAguado/Smart_Plant

    The Smart Plant is a board that can be plugged directly on the soil, close to the plant, that allows the measurement of the environment (soil moisture, environment temperature & illuminance), and presents the…

    75 parts303
  • 2 layers80 × 107.5 mmMinino, the printed circuit board in 3D

    Minino

    ElectronicCats/Minino

    Minino is an original multiprotocol and multiband board made for sniffing, communicating, and attacking IoT devices. It was designed as a mini Cat that integrates the powerful ESP32C6, GPS, microSD and OLED.

    79 parts183GPL-3.0
  • 2 layers92.8 × 71.8 mmUSBSID Pico v1.3f, the printed circuit board in 3D

    USBSID Pico v1.3f

    LouDnl/USBSID-Pico

    USBSID-Pico is a RPi Pico (RP2040/W RP2350/W) based board for interfacing one or two MOS SID chips and/or hardware SID emulators over (WEB)USB with your computer, phone, ASID supporting player or USB midi controller

    116 parts125GPL-2.0
  • 2 layers16.3 × 11.7 mmBrains, the printed circuit board in 3D

    Brains

    atomic14/ch32v003-audio

    A collection of audio projects for the CH32V003J4M6 RISC-V microcontroller, demonstrating various audio synthesis and playback techniques on an 8-pin, $0.10 microcontroller.

    15 parts78MIT

Questions

How big is the Fluidnc bob PCB?

It measures 82.4 × 62.5 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Fluidnc bob use?

49 parts, built around the SN74HC541N, GS1A, 1210L150/16WR and MMBT2222A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Fluidnc bob KiCad files?

From the drewsipher/sharkcnc repository on GitHub, at the commit this page was made from: the board is hardware/fluidnc-bob/fluidnc-bob.kicad_pcb and its schematic hardware/fluidnc-bob-revD/fluidnc-bob-revD.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Fluidnc bob design in my own project?

Its repository states no licence, so its author keeps all rights: ask drewsipher before reusing the design.