Skip to the content
2 layers90.4 × 98.7 mmFluidnc bob revD, the printed circuit board in 3D

Fluidnc bob revD

drewsipher/sharkcnc

Open CNC control stack for a Sherline 2000: FluidNC ESP32-S3 breakout hardware + host software plan

Size
90.4 × 98.7 mm
Copper layers
2
Thickness
1.6 mm
Parts
66
Nets
76
Pads
214
Tracks, vias
321, 0
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
18 Jul 2026
Updated
6 Aug 2026

Overview

Fluidnc bob revD is an open-source printed circuit board by drewsipher, from the drewsipher/sharkcnc repository on GitHub. It is a 2-layer board of 90.4 × 98.7 mm with 66 parts on 76 nets, routed with 321 tracks and 0 vias.

It is built around the SN74AHCT541N, MMBT2222A and S1M, with the SMBJ5.0A among its other parts. Its parts include 31 resistors, 11 connectors, 10 capacitors, 4 diodes and 2 transistors. It belongs with the interfaces and adapters boards and the ESP32 boards of this library.

Main components

4

README

hardware/fluidnc-bob/README.md

fluidnc-bob rev C — ESP32-S3 FluidNC breakout (schematic + netlist)

FluidNC controller interface for the Sherline 2000 / FMD2740C drivers: socketed 44-pin dual-USB-C ESP32-S3-WROOM-1 (N16R8) devkit, SN74HC541N 5 V buffer (VCC dropped through a GS1A so 3.3 V inputs meet V_IH), filtered limit/probe inputs, microSD breakout header, spindle relay driver. All connections are solder wire pads — no connectors.

Deliverable = schematic + verified netlist + footprint assignments. Board layout is done by hand in KiCad ("Update PCB from Schematic" pulls in everything, including the custom footprints in fluidnc-bob.pretty/).

Design state: ERC clean (0 violations); netlist machine-verified against generate/design.py (generate/verify_netlist.py — partition and power-net comparison). Unbuilt, rev C.

⚠ Layout-time checklist

  1. MEASURE THE DEVKIT ROW SPACING. The socket footprint assumes 22.86 mm (0.9"); both 22.86 and 25.4 mm exist among 44-pin S3 boards. Set ROWSP in generate/gen_fp.py (or edit the footprint) to match, and check the devkit's printed pin legend against DEVKIT_LEFT/RIGHT in generate/design.py (pin 1 = 3V3, antenna end).
  2. N16R8 (octal PSRAM): GPIO 35/36/37 intentionally unconnected.
  3. U1's buffer channels are interchangeable — permute freely during routing.
  4. Keep the FMD2740C signal runs and logic ground away from motor power; single-point ground at the supply.
  5. Don't feed 5 V and devkit USB simultaneously unless the devkit's backfeed diode is verified.

Wire pad groups

RefPads (1 = square)Goes to
J15V, GND5 V PSU (through F1 polyfuse, D2 reverse crowbar)
J2STEP, DIR, GNDX driver: SP+, DIR+; GND wire bridges SP−+DIR−
J3STEP, DIR, GNDY driver
J4STEP, DIR, GNDZ driver
J5 / J6SIG, GNDX / Y limit switch (closes to GND)
J10 / J11SIG, GNDZ limit / probe
J7+5V, COIL−spindle relay coil (2N7000 low side, D1 flyback)
J8AUX, GNDspare buffered 5 V output
J9SCK, MISO, MOSI, CS, 5V, GNDmicroSD breakout (feed it 5 V; its 4050 + 3.3 V reg handle the rest)

GPIO map (ESP32-S3)

SignalGPIOSignalGPIO
X step / dir18 / 17X / Y / Z limit42 / 2 / 1
Y step / dir16 / 15Probe41
Z step / dir7 / 6SD SCK / MISO / MOSI / CS12 / 13 / 11 / 10
Spindle relay5Aux out4

Inputs: 10 k pullup to 3V3 + 1 k series + 100 nF on board.

FluidNC config

The maintained config is config.yaml (bench bring-up, as-built active-high step/dir; limits/probe are :low because the board pulls them up and switches close to GND). Verified against FluidNC v4.0.3 example syntax — note it is sdcard:, not sd:.

If the drivers are reworked to common-anode (SP+/DIR+ tied to +5V), add :low to every step_pin and direction_pin.

Upload jobs to SD and run locally — WiFi then carries only status/jog and can never stall a cut. Verify pin syntax against the FluidNC wiki for the S3 release you flash.

Regenerating / verifying

sh
python3 generate/gen_fp.py        # footprints (socket ROWSP lives here)
python3 generate/gen_sch.py       # schematic (drawn wires; self-checks)
kicad-cli sch erc --exit-code-violations fluidnc-bob.kicad_sch
python3 generate/verify_netlist.py  # diff KiCad netlist vs design.py

generate/design.py is the netlist source of truth. generate/gen_pcb.py is retired (the rev B auto-layout experiment) — kept for reference only; it no longer matches the current design.

Parts

66
QtyValueFootprintReferences
10100kResistor_SMD:R_0805_2012MetricR10, R11, R12, R13, R14, R15, R16, R17, R41, R43
91kResistor_SMD:R_0805_2012MetricR30, R31, R32, R33, R34, R40, R42, R50, R51
7100RResistor_SMD:R_0805_2012MetricR60, R61, R62, R63, R64, R65, R66
7100nFCapacitor_SMD:C_0805_2012MetricC4, C5, C20, C21, C22, C23, C24
510kResistor_SMD:R_0805_2012MetricR20, R21, R22, R23, R24
3M3MountingHole:MountingHole_3.2mm_M3_PadH1, H2, H3
2C_Polarized_USCapacitor_THT:CP_Radial_D8.0mm_P3.80mmC2, C6
2MMBT2222APackage_TO_SOT_SMD:SOT-23Q1, Q2
110uF/25VCapacitor_SMD:C_1206_3216MetricC3
12AFuse:Fuse_1206_3216MetricF1
15V-INTerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_HorizontalJ1
1AUXConnector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ11
1E-STOPConnector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ9
1EN+XTerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-5-5.08_1x05_P5.08mm_HorizontalJ2
1ESP32-S3-DevKit-44fluidnc-bob-revD:ESP32_S3_DevKit_44_SocketA1
1G5LE-14 DC5Relay_THT:Relay_SPDT_Omron-G5LE-1RLY1
1LIM-XConnector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ5
1LIM-YConnector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ6
1LIM-ZConnector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ7
1MOTORS-OFFLED_THT:LED_D5.0mmLED2
1PROBEConnector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ8
1PWRLED_THT:LED_D5.0mmLED1
1S1MDiode_SMD:D_SMAD2
1SDConnector_PinHeader_2.54mm:PinHeader_2x06_P2.54mm_VerticalJ13
1SMBJ5.0ADiode_SMD:D_SMBD1
1SN74AHCT541NPackage_DIP:DIP-20_W7.62mm_SocketU1
1SPINDLE-SWTerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-3-5.08_1x03_P5.08mm_HorizontalSPINDLE
1X+YTerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-5-5.08_1x05_P5.08mm_HorizontalJ3
1Z+5TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-5-5.08_1x05_P5.08mm_HorizontalJ4

More from drewsipher/sharkcnc

1
  • 4 layers82.4 × 62.5 mmFluidnc bob, the printed circuit board in 3D

    Fluidnc bob

    drewsipher/sharkcnc

    Open CNC control stack for a Sherline 2000: FluidNC ESP32-S3 breakout hardware + host software plan

    49 parts

Similar boards

  • 2 layers205.4 × 99.9 mmImp, the printed circuit board in 3D

    Imp

    nmatic00/max1491-4wire-ohmmeter

    My first KiCAD project. 4 Wire Kelvin Ohmmeter based on MAX1491 ADC.

    91 partsMIT
  • 2 layers100 × 44 mmOpensolder, the printed circuit board in 3D

    Opensolder

    howie-j/opensolder

    Fully open source JBC T245-compatible soldering station

    69 parts55GPL-3.0
  • 4 layersIONPAK2, the printed circuit board in 3D

    IONPAK2

    m-labs/ionpak

    A modern, low-cost universal controller for hot-cathode ionization vacuum gauges. (WIP)

    259 parts23
  • 2 layers143 × 97 mmPihat all, the printed circuit board in 3D

    Pihat all

    yope/kamaq

    Python/Cython implementation of 3D printer firmware running on Linux

    305 parts11GPL-2.0
  • 2 layers18.1 × 18.2 mmMk3 fan adapter, the printed circuit board in 3D

    Mk3 fan adapter

    magkopian/prusa-mk3-24v-dual-fan-adapter

    Dual 24V Fan Adapter for the Original Prusa i3 MK3

    7 parts5CC-BY-SA-4.0
  • 2 layers86.4 × 53.3 mmAh board, the printed circuit board in 3D

    Ah board

    dglcinc/pivac

    Python library to vacuum data from Raspberry-Pi-based monitoring and control solutions (like HVAC)

    53 parts2
  • 2 layers80 × 74 mmHubble metal detector, the printed circuit board in 3D

    Hubble metal detector

    zartarn15/hubble-metal-detector

    STM32-based digital metal detector with custom hardware and embedded DSP firmware.

    156 parts2
  • 2 layers100 × 100 mmEvse, the printed circuit board in 3D

    Evse

    artashesamatuni/coreEVSE

    coreEVSE KiCad hardware project

    118 parts1

Questions

How big is the Fluidnc bob revD PCB?

It measures 90.4 × 98.7 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Fluidnc bob revD use?

66 parts, built around the SN74AHCT541N, MMBT2222A, S1M and SMBJ5.0A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Fluidnc bob revD KiCad files?

From the drewsipher/sharkcnc repository on GitHub, at the commit this page was made from: the board is hardware/fluidnc-bob-revD/fluidnc-bob-revD.kicad_pcb and its schematic hardware/fluidnc-bob-revD/fluidnc-bob-revD.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Fluidnc bob revD design in my own project?

Its repository states no licence, so its author keeps all rights: ask drewsipher before reusing the design.