Skip to the content
2 layers100 × 100 mmLtc3331-breakout, the printed circuit board in 3D

Cheap alternative dev-board for the LTC3331 energy harvesting chip

Size
100 × 100 mm
Copper layers
2
Thickness
1.6 mm
Parts
73
Nets
56
Pads
317
Tracks, vias
738, 70
Pours
2
Routed
Yes
KiCad
KiCad 4
Created
4 Jul 2017
Updated
12 May 2018

Overview

Ltc3331-breakout is an open-source printed circuit board by dpiegdon, from the dpiegdon/ltc3331-breakout repository on GitHub. It is a 2-layer board of 100 × 100 mm with 73 parts on 56 nets, routed with 738 tracks and 70 vias.

It is built around the NC7SZ58P6X, CR2032 and NDC7001C. Its parts include 24 connectors, 13 capacitors, 6 resistors, 3 ICs and 2 transistors. It belongs with the interfaces and adapters boards of this library.

Main components

3

README

README.md

Open, low-cost experimentation board for the LTC3331 energy harvesting chip

This project contains design- and production-files for a low-cost LTC3331 energy harvesting development-, breakout- and test-board.

It's specifically designed to be inexpensive, yet open and comprehensive:

  • Full design files for KiCad EDA
  • 10cm x 10cm PCB with 2 layers
  • Full pin breakout
  • Less-comprehensive headers for pins usually required
  • LIR2032 holder and alternative battery port
  • All default options can be jumpered on or off
  • Supercap pads provided

PCB v0.1 rendering from KiCad

(Above: v0.1, image rendered by KiCad EDA)

PCB v0.1 photo

(Above: v0.1, actual photo of both sides)

Releases and History

All production files for releases can be found in the production/ directory. All required production files for PCB production should be zipped in a way that allows immediate upload to your preferred online PCB manufacturer.

v0.1 is the first version of the PCB. It has a few minor issues (see Errata), but is fine for testing.

Errata

v0.1

v0.1 works fine, but there are a few issues that should be addressed for another release:

Schematic:

  • jumper for BBIN-BATIN connection is not needed.

  • scatter more GND connectors for oscilloscope use

  • maybe provide circuit for higher current charging, as seen in datasheet figure 7, pg 27?

  • extra small header for GND/AC1/AC2/VIN

Footprints:

  • footprints for 22uF inductors on bottom layer are way too large. a Taiyo-Yuden NR-30xx handsoldering footprint would be fine and should be moved to the front side. then there would be no components on the bottom.

  • replace all capacitance footprints >= 10uF with larger footprint for e.g. tantalum capacitor.

  • make cap footprints dual-use: through-hole AND smd?

PCB Placement / Routing:

  • reorder all selection jumpers so they comply the the datasheet table

Silkscreen:

  • mark down input voltage limits (3-19V)

  • add white box for charge-current-resistor value placed by user

  • if enough place, print cap values (and voltage ratings?)

Other:

  • pdf schematic was missing in release files (was added later). next release should contain that immediately.

Prior Art and Alternatives

Please note: personally I did not obtain any of the following alternatives, so any comparison is a rough guess.

DC2151A is the de-facto standard demo- and dev-board that Linear Technology created for this chip. However, it's really expensive. (200+ €/$)

The "LTC3331 Energy Harvester, DC Converter and Charger" by Blue Spark Labs is a much cheaper alternative to the official dev-board. But it seemingly does not offer comprehensive access to all pins and full breakout options. Also, worldwide shipping can be quite expensive, it seems.

Use

When you want to use or modify the design in KiCad, you should get used to handling git-submodules. I keep my custom footprints and symbols in a separate repository so I can re-use them.

Have fun!

Feedback

If you have design improvements, find it useful or stupid, or want to let me know anything else, just let me know ;).

License, copyright

The design is released under the OSHW 1.0 license as defined by [https://www.oshwa.org/definition/].

Parts

73
QtyValueFootprintReferences
20JumperPin_Headers:Pin_Header_Straight_1x02_Pitch2.54mmJP1, JP2, JP3, JP4, JP5, JP10, JP11, JP12, JP13, JP14, JP15, JP16, JP17, JP18, JP19, JP21 +4
9CONN_01X03Pin_Headers:Pin_Header_Straight_1x03_Pitch2.54mmJ6, J7, J8, J10, J11, J12, J14, J15, J16
6DNPCapacitors_SMD:CP_Elec_10x10C8, C9, C10, C11, C12, C13
5Conn_02x02_Odd_EvenPin_Headers:Pin_Header_Straight_2x02_Pitch2.54mmJ19, J20, J21, J22, J23
4CONN_02X08Pin_Headers:Pin_Header_Straight_2x08_Pitch2.54mmJ1, J2, J3, J4
3CONN_01X04Pin_Headers:Pin_Header_Straight_1x04_Pitch2.54mmJ5, J9, J13
21MResistors_SMD:R_1206_HandSolderingR2, R5
222uHInductors:Inductor_Taiyo-Yuden_NR-30xx_HandSolderingL1, L2
24.7uF 6.3Vfootprints:CAP_Generic_SMD_Radial_D10.0mm_P2.50mm_P5.00mmC3, C6
2NC7SZ58TO_SOT_Packages_SMD:SOT-363_SC-70-6_HandsolderingU1, U2
10.1uF 10VCapacitors_SMD:C_1206_HandSolderingC4
110Resistors_SMD:R_1206_HandSolderingR3
1100KResistors_SMD:R_1206_HandSolderingR4
1150uF 6.3Vfootprints:CAP_Generic_SMD_Radial_D10.0mm_P2.50mm_P5.00mmC7
11uF 6.3VCapacitors_SMD:C_1206_HandSolderingC1
122uF 25Vfootprints:CAP_Generic_SMD_Radial_D10.0mm_P2.50mm_P5.00mmC2
122uF 6.3Vfootprints:CAP_Generic_SMD_Radial_D10.0mm_P2.50mm_P5.00mmC5
13KResistors_SMD:R_1206_HandSolderingR1
156.2Resistors_SMD:R_1206_HandSolderingR6
1CMOSH-3Diodes_SMD:D_SOD-523D1
1CMPT3906ETO_SOT_Packages_SMD:SOT-23Q2
1CONN_01X02Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mmJ17
1CONN_01X02_FEMALEPin_Headers:Pin_Header_Straight_1x02_Pitch2.54mmJ18
1CONN_02X12Pin_Headers:Pin_Header_Straight_2x12_Pitch2.54mmJ24
1CR2032footprints:SMTU-2032-LFBT1
1Jumper_NC_DualPin_Headers:Pin_Header_Straight_1x03_Pitch2.54mmJP20
1LTC3331Housings_DFN_QFN:QFN-32-1EP_5x5mm_Pitch0.5mmIC1
1NDC7001CTO_SOT_Packages_SMD:SuperSOT-6Q1

Similar boards

  • 2 layers333.4 × 149.9 mmOmega Mainboard, the printed circuit board in 3D

    Omega Mainboard

    skiselev/omega

    Omega Home Computer

    248 parts459GPL-3.0
  • 2 layers17.2 × 30.4 mmWeigand, the printed circuit board in 3D

    Weigand

    linklayer/BLEKey

    A Bluetooth Low Energy device for interfacing with Wiegand

    17 parts268
  • 4 layers188 × 188 mmITX Llama, the printed circuit board in 3D

    ITX Llama

    eivindbohler/itxllama

    422 parts246GPL-3.0
  • 2 layers61 × 36.8 mmKeebcard, the printed circuit board in 3D

    Keebcard

    rsheldiii/Keebcard

    Home of the KeebCard project - Kicad files, code, and more!

    15 parts112
  • 2 layers59.2 × 41 mmBluey, the printed circuit board in 3D

    Bluey

    electronut/ElectronutLabs-bluey

    Nordic nRF52832 BLE development board with sensors.

    79 parts96
  • 2 layers35 × 35 mmQron0b, the printed circuit board in 3D

    Qron0b

    qewer33/qron0b

    a sleek and low-power binary wristwatch

    35 parts62GPL-3.0
  • 2 layers90 × 89.4 mm38-04-usb sleuth, the printed circuit board in 3D

    38-04-usb sleuth

    smaroukis/usb-sleuth

    USB cable continuity tester ++

    68 parts61
  • 2 layers170.2 × 100 mmZ80-SBC, the printed circuit board in 3D

    Z80-SBC

    skiselev/zeta_sbc

    Zeta SBC is an Zilog Z80 based single board computer. It is inspired by Ampro Little Board Z80 and N8VEM project. Zeta SBC is software compatible with RomWBW Firmware

    75 parts53GPL-3.0

Questions

How big is the Ltc3331-breakout PCB?

It measures 100 × 100 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Ltc3331-breakout use?

73 parts, built around the NC7SZ58P6X, CR2032 and NDC7001C. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Ltc3331-breakout KiCad files?

From the dpiegdon/ltc3331-breakout repository on GitHub, at the commit this page was made from: the board is ltc3331-breakout.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Ltc3331-breakout design in my own project?

Its repository states no licence, so its author keeps all rights: ask dpiegdon before reusing the design.