

LoRA!!
- Size
- 68.3 × 94.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 40
- Nets
- 60
- Pads
- 233
- Tracks, vias
- 932, 181
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 5 Oct 2026
- Updated
- 25 Oct 2026
Overview
LORA is an open-source printed circuit board by dipa-cotton, from the dipa-cotton/lora-puck repository on GitHub. It is a 2-layer board of 68.3 × 94.8 mm with 40 parts on 60 nets, routed with 932 tracks and 181 vias.
It is built around the ESP32-S3-WROOM-1-N8, PE4259-63 and SX1262IMLTRT, with the AMS1117-3.3 and 0900FM15K0039E among its other parts. Its parts include 14 capacitors, 8 connectors, 5 resistors, 5 ICs and 2 switches. It belongs with the radio and wireless boards and the ESP32 boards of this library.
Main components
5ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesPE4259-63
SC-70-6-40℃~+85℃ 0.35dB 1.8V~3.3V 10MHz~3GHz 30dB 33.5dBm Integrated control logic SPDT SC-70-6 RF Switches ROHSpSemiRF SwitchesSX1262IMLTRT
QFN-24-EP(4x4)-148dBm -40℃~+85℃ 1.8V~3.7V 150MHz~960MHz 22dBm 300Kbps 32mA 4.2mA ISM SPI Supports software reset、Power-on reset function、Supports RSSI function transceiver QFN-24-EP(4x4) RF Transceiver ICs ROHSSEMTECHRF Transceiver ICsAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators0900FM15K0039E
SMD-10P,1.2x2mmSMD-10P,1.2x2mm Ceramic Filters ROHSJohanson DielectricsCeramic Filters
README
README.mdlora-puck
LoRA!!
pictures
project overview
A long range radio system with lots of features! it integrates boards with sensors and reads the data with an esp32, and communicates using an SX1262, on ham radio frequencies so i can pick them up from far far away :DD along with a 0.96 inch OLED display, a microSD card module, and more, this project is versatile and can do much more than your average tiny radio!
Parts
40| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 100nf | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C1, C3, C4 |
| 2 | 10 µF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C6, C7 |
| 2 | 10k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R3, R4 |
| 2 | 3.3 pf | Resistor_SMD:R_0603_1608Metric | C10, C11 |
| 2 | 5.1K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1, R2 |
| 2 | SW_Push | Button_Switch_SMD:SW_Push_1P1T_NO_CK_PTS125Sx43SMTR | SW1, SW2 |
| 1 | 0.1µF | Resistor_SMD:R_0603_1608Metric | C14 |
| 1 | 0900FM15K0039 | RF_Converter:Balun_Johanson_0900FM15K0039 | FL2 |
| 1 | 10D | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 10µF | Resistor_SMD:R_0603_1608Metric | C13 |
| 1 | 15µH | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | L1 |
| 1 | 1µF | Resistor_SMD:R_0603_1608Metric | C2 |
| 1 | 39pf | Resistor_SMD:R_0603_1608Metric | C9 |
| 1 | 4.7 µF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C5 |
| 1 | 7700 Ambient Light Sensor | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J5 |
| 1 | 9.1nH | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | L2 |
| 1 | AHT20+BMP280 Temperature Humidity Air Pressure | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | Battery | Battery:BatteryHolder_Keystone_2462_2xAA | BT1 |
| 1 | C | Resistor_SMD:R_0603_1608Metric | C8 |
| 1 | C_Polarized | Capacitor_THT:C_Radial_D6.3mm_H7.0mm_P2.50mm | C12 |
| 1 | Crystal_GND24 | Crystal:Crystal_DS10_D1.0mm_L4.3mm_Horizontal_1EP_style1 | Y1 |
| 1 | ENS160+AHT21 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J2 |
| 1 | ESP32-S3-WROOM-1 | RF_Module:ESP32-S3-WROOM-1 | U1 |
| 1 | FerriteBead | Ferrite_THT:LairdTech_28C0236-0JW-10 | FB1 |
| 1 | GY-NEO6MV2 New NEO-6M GPS | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J6 |
| 1 | MCP1700x-330xxTO | Package_TO_SOT_THT:TO-92_Inline | U5 |
| 1 | Micro_SD_Card | Connector_Card:microSD_HC_Wuerth_693072010801 | J7 |
| 1 | OLED | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J8 |
| 1 | PE4259 | Package_TO_SOT_SMD:SOT-363_SC-70-6 | U4 |
| 1 | SX1262IMLTRT | Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U2 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_GCT_USB4085 | J1 |
| 1 | UV Sensor 240-370nm GUVA-S12SD 3528 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J3 |
Similar boards
- 4 layers30.5 × 72.9 mm

- 2 layers76 × 35 mm

Ground station
Horizon-Avionics/Horizon-H1
Building a fully open-source flight computer for amateur rocketry!
38 parts17 - 4 layers61.8 × 79.6 mm

- 4 layers40.5 × 80.2 mm

NULL
jadenvv/NULL
A version of a flipperzero that has the same capabilities of Sub-GHz RF, IR, Wifi, and NFC/RFID
121 parts1 - 4 layers68 × 73.5 mm

Messenger
nickzentmayer/Messenger
This is a repository of hardware and software for a SX1262 radio based messageing device I made. This device supports a messaging protocol named Hermes that I created with insperation from protocols like TCP.
91 parts1 - 4 layers42 × 42 mm

LaRa Puck
Sai-Santosh09/RouteSync
RouteSync is a compact, LoRa-based communication device designed for long-range messaging and emergency location sharing in environments where cellular networks are unavailable.
55 parts1 - 4 layers38.3 × 49.3 mm

Nexus Cypher
WIZTHECYBER/LoRa-RF-PCB
This is PCB for long rang radio frequency communication
54 parts1CERN-OHL-S-2.0 - 4 layers21 × 51 mm

Devboard
AayanShaikh007/Nano_LoRa
The project started while I was building a Raspberry Pi Pico-based keyboard. I wanted an affordable, flexible development board that could support wireless projects without requiring a separate radio module or an…
65 parts
Questions
How big is the LORA PCB?
It measures 68.3 × 94.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the LORA use?
40 parts, built around the ESP32-S3-WROOM-1-N8, PE4259-63, SX1262IMLTRT and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the LORA KiCad files?
From the dipa-cotton/lora-puck repository on GitHub, at the commit this page was made from: the board is src/kicad files/LORA.kicad_pcb and its schematic src/kicad files/LORA.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the LORA design in my own project?
Its repository states no licence, so its author keeps all rights: ask dipa-cotton before reusing the design.