2 layers72.8 × 32 mm
2 layers32.1 × 41.2 mm
Ir signalgen lite
dilshan/ir-clone58Open-source infrared remote control signal analysis and generating tool
- Size
- 32.1 × 41.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 40
- Nets
- 31
- Pads
- 122
- Tracks, vias
- 442, 34
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 12 Feb 2022
- Updated
- 25 Feb 2022
Overview
Ir signalgen lite is an open-source printed circuit board by dilshan, from the dilshan/ir-clone repository on GitHub, published under the MIT licence. It is a 2-layer board of 32.1 × 41.2 mm with 40 parts on 31 nets, routed with 442 tracks and 34 vias.
It is built around the STM8S003F3P6, 24LC32A/P and AMS1117-3.3, with the MMBT3904 among its other parts. Its parts include 10 capacitors, 9 resistors, 4 ICs, 4 connectors and 2 diodes. It belongs with the computers and single-board computers boards and the STM8 boards of this library.
Main components
4
STM8S003F3P6
TSSOP-20-40℃~+85℃ 10bit 128Byte 16 16MHz 1KB 2.95V~5.5V 8 Bit 8KB Built-in FLASH STM8 TSSOP-20 Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)
24LC32A/P
PDIP-80℃~+70℃ 2.5V~5.5V 32Kbit 400kHz 5ms I2C PDIP-8 EEPROM ROHSMicrochip TechnologyEEPROM
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
MMBT3904
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mA 200mW 300MHz 300mV 40V 6V NPN SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)
Parts
40| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 0.1MFD | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C102, C103, C202, C204, C301, C302 |
| 3 | 4.7K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R301, R302, R305 |
| 2 | 10K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R201, R303 |
| 2 | MMBT3904 | Package_TO_SOT_SMD:SOT-23 | Q301, Q302 |
| 2 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad | H101, H102 |
| 2 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP301, TP302 |
| 1 | 10MFD | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C101 |
| 1 | 1K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R202 |
| 1 | 1MFD | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C201 |
| 1 | 1MFD | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C203 |
| 1 | 22K | Resistor_SMD:R_Array_Convex_4x0603 | RN201 |
| 1 | 22K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R304 |
| 1 | 24LC32 | Package_DIP:DIP-8_W7.62mm_Socket_LongPads | U302 |
| 1 | 4.7MFD | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C104 |
| 1 | 470R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R307 |
| 1 | 56R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R306 |
| 1 | 60-2S1M | Button_Switch_THT:SW_PUSH_6mm | SW201 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U101 |
| 1 | BAT-IN | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J102 |
| 1 | DC-IN | Connector_Phoenix_MC:PhoenixContact_MCV_1,5_2-G-3.5_1x02_P3.50mm_Vertical | J101 |
| 1 | GREEN-3mm | LED_THT:LED_D3.0mm | D302 |
| 1 | ICP | ir-signalgen-lite:pogo-2.54mmx4 | J201 |
| 1 | KEYMATRIX | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J202 |
| 1 | LD271 | LED_THT:LED_D5.0mm_Horizontal_O1.27mm_Z3.0mm | D301 |
| 1 | MODE | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP202 |
| 1 | PROG | Jumper:SolderJumper-2_P1.3mm_Bridged_Pad1.0x1.5mm | JP201 |
| 1 | PWR-SRC | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP101 |
| 1 | STM8S003F3P | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U201 |
| 1 | TSOP1838 | OptoDevice:Vishay_MOLD-3Pin | U301 |
Similar boards
- 4 layers71.1 × 99.1 mm
- 2 layers87.6 × 64 mm
EFuse voltmeter r6
jerryok826/eFuse_voltmeter
A protection circuit for down stream devices.
90 parts1MIT - 2 layers147.3 × 154.4 mm
- 4 layers
Kvm base
thatoddmailbox/kvm-base
The main board for the open-source HDMI KVM switch I built.
70 parts19 - 2 layers65 × 56 mm
Ras pi supercap ups
akuker/SuperUPS
This is a fork of the original Supercapacitor UPS board for a Raspberry Pi by Scott Baker, http://www.smbaker.com/
88 parts7 - 2 layers25.4 × 33 mm
- 2 layers26.4 × 18.8 mm
STM8S003F3
TLDR-Electronics/STM8S003F3_PCB_Breakout_and_C_examples
STM8S003F3 Breakout board and Simple STM8 C examples with the SDCC compiler
16 parts4MIT
Questions
How big is the Ir signalgen lite PCB?
It measures 32.1 × 41.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Ir signalgen lite use?
40 parts, built around the STM8S003F3P6, 24LC32A/P, AMS1117-3.3 and MMBT3904. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Ir signalgen lite KiCad files?
From the dilshan/ir-clone repository on GitHub, at the commit this page was made from: the board is design/ir-signalgen-lite.kicad_pcb and its schematic design/ir-signal-gen-interface.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Ir signalgen lite design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).