
SmartTherm
Strooom/SmartTherm
Controlling a Junkers heating (Eurostar ZWE24) with an IoT thermostat

A PCB to learn soldering for younger kids
Bunny is an open-source printed circuit board by DG1JAN, from the DG1JAN/solderbunny repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 2-layer board of 42.9 × 47.5 mm with 14 parts on 8 nets, routed with 73 tracks and 2 vias.
It is built around the BC546. Its parts include 4 resistors, 2 capacitors, 2 diodes, 2 transistors and 1 connector.
A PCB to learn soldering for younger kids


2x 47 Ohm (0207)
2x 15 kOhm (0270) can also be 10 - 25kOhm (will verry blinking frequency)
2x LED 5mm
2x BC546 (TO92 NPN, also 547,548 etc is fine)
2x 42uF Capaciator (Elko)
1x 3V Battery+Housing (e.g. CR2032, 2x1,5V AA,..)
| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | , | ||
| 2 | 15k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2, R3 |
| 2 | 47 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R4 |
| 2 | BC546 | Package_TO_SOT_THT:TO-92_Wide | Q1, Q2 |
| 2 | C_Polarized | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C1, C2 |
| 2 | LED | LED_THT:LED_D5.0mm | D1, D2 |
| 1 | Conn_01x02 | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J1 |
The 13 most common of 14 parts.

Strooom/SmartTherm
Controlling a Junkers heating (Eurostar ZWE24) with an IoT thermostat



bildschirmtext/rpi-dbt03
Hardware, Software and Firmware for a Raspberry Pi to DBT-03 adapter

bigbass1997/PICTAS
Low-cost replay device for playing back Tool Assisted Speedruns on real hardware

Wesemane-Industries/808-kick-eurorack
808 kick (bass drum) for eurorack / modular synth

m0xpd/EUCLIDplus
EUCLID+ is a Clock Divider, Oscillator and Rhythm Sequencer for electronic music applications

m0xpd/FLIP
A Bernoulli Gate for Electronic Music Applications, realised in Hardware
It measures 42.9 × 47.5 mm and has 2 copper layers, 1.6 mm thick.
14 parts, built around the BC546. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the DG1JAN/solderbunny repository on GitHub, at the commit this page was made from: the board is bunny.kicad_pcb and its schematic bunny.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).