
Rdi dbt03 multiplexer
bildschirmtext/rpi-dbt03
Hardware, Software and Firmware for a Raspberry Pi to DBT-03 adapter

Hardware, Software and Firmware for a Raspberry Pi to DBT-03 adapter
Rpi dbt03 is an open-source printed circuit board by bildschirmtext, from the bildschirmtext/rpi-dbt03 repository on GitHub, published under the MIT licence. It is a 2-layer board of 64 × 56 mm with 36 parts on 41 nets, routed with 204 tracks and 0 vias.
It is built around the ATMEGA8L-8PU, SFH617A-1 and BC546. Its parts include 13 resistors, 6 capacitors, 5 diodes, 4 ICs and 3 switches. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Hardware, Software and Firmware for a Raspberry Pi to DBT-03 adapter
There is now a possibility to directly patch a Bookworm Raspbian image.
Run ./patch_image.sh <imagename> as root. It only works on uncompressed images. You can then dd that image onto your SD-card or use the Raspberry Pi Imager. The later also allows you to set settings.
The image will reboot multiple times.
The boot partition can also hold a btx_config.txt file where you can configure the host to connect to.
BTX_HOST=btx.clarke-3.de
BTX_PORT=20000On the Raspberry PI check out this repository.
Install the packages in install-packages.sh (run it as root).
Enable spi with raspi-config.
Change the baudrate of the programmer "linuxspi" to a smaller value 40000 is OK. This setting is found in /etc/avrdude.conf
This currently is still incomplete.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 470 | Resistors_ThroughHole:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R5, R6, R13, R14 |
| 5 | LED | LEDs:LED_D3.0mm | D1, D2, D3, D4, D5 |
| 3 | 10k | Resistors_ThroughHole:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2, R3, R4 |
| 3 | 2k2 | Resistors_ThroughHole:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R10, R11, R12 |
| 3 | SFH617A-1 | Housings_DIP:DIP-4_W7.62mm_Socket_LongPads | U2, U3, U4 |
| 3 | SW_Push | Buttons_Switches_ThroughHole:SW_PUSH_6mm | SW1, SW2, SW3 |
| 2 | KERKO 15P | Capacitors_ThroughHole:C_Disc_D3.0mm_W1.6mm_P2.50mm | C1, C3 |
| 2 | TANTAL 2,2/16 | Capacitors_ThroughHole:CP_Radial_Tantal_D4.5mm_P2.50mm | C4, C5 |
| 1 | 0r | Resistors_ThroughHole:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R9 |
| 1 | 1M | Resistors_ThroughHole:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R8 |
| 1 | 8MHz | Crystals:Crystal_HC49-4H_Vertical | Y1 |
| 1 | ATmega8L-8PU | Housings_DIP:DIP-28_W7.62mm | U1 |
| 1 | BC546 | TO_SOT_Packages_THT:TO-92_Inline_Wide | Q1 |
| 1 | Conn_02x02_Counter_Clockwise | Pin_Headers:Pin_Header_Straight_2x02_Pitch2.54mm | J1 |
| 1 | Conn_02x03_Odd_Even | Pin_Headers:Pin_Header_Straight_2x03_Pitch2.54mm | J2 |
| 1 | EB-A 10U 63 | Capacitors_ThroughHole:CP_Radial_D5.0mm_P2.50mm | C2 |
| 1 | Raspberry_Pi_2_3 | Raspberry-Pi-3-library-for-kicad:raspberrypi_2_3 | RP1 |
| 1 | TANTAL 2,2/16 | Capacitors_ThroughHole:C_Disc_D3.0mm_W2.0mm_P2.50mm | C6 |

bildschirmtext/rpi-dbt03
Hardware, Software and Firmware for a Raspberry Pi to DBT-03 adapter



IdahoLabResearch/AcCCS
A collection of tools and scripts used to communicate and emulate Electric Vehicle Communication Controllers (EVCC) and Supply Equipment Communication Controllers (SECC).


lal12/vaillant-heater-control-esp
This project contains a little board (and software) to control a Vaillant heater.

LSUTigerRacing/Electronics
This repository contains all of the KiCad Schematics for the 2026 TigerRacing Formula SAE's Electronics Subsystem.

bhaskar9980/Guardian
Guardian is an advanced, fully automated hydroponics system designed to optimize plant growth and maximize yield.

JacobParent7/FSAE_ELECTRONICS
Repository for Fault Latch, BSPB, TSIL (TSSI) , TSAL (RML),
It measures 64 × 56 mm and has 2 copper layers, 1.6 mm thick.
36 parts, built around the ATMEGA8L-8PU, SFH617A-1 and BC546. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the bildschirmtext/rpi-dbt03 repository on GitHub, at the commit this page was made from: the board is rpi_dbt03_2/rpi_dbt03.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).