

Ultimate LPS
Simple and affordable power supply
- Size
- 150 × 100 mm
- Copper layers
- 4
- Thickness
- 1.66 mm
- Parts
- 97
- Nets
- 49
- Pads
- 215
- Tracks, vias
- 388, 0
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 14 Oct 2026
- Updated
- 15 Oct 2026
Overview
Ultimate LPS is an open-source printed circuit board by BTTLab, from the BTTLab/simple_and_affordable_lps repository on GitHub, published under the MIT licence. It is a 4-layer board of 150 × 100 mm with 97 parts on 49 nets, routed with 388 tracks and 0 vias.
It is built around the LM324, LM393 and LM7805, with the LM7812, BC546 and BD140 among its other parts. Its parts include 44 resistors, 15 capacitors, 14 diodes, 8 connectors and 4 ICs. It belongs with the power boards of this library.
Main components
7LM324
SOP-14-1.5V~10V 0℃~+70℃ 24V 250nA 3V~20V 4 40mA 50nA 700uA 7mV 80dB SOP-14 Operational Amplifier ROHSHXY MOSFETOperational AmplifierLM393
SOP-8-16V~16V 0℃~+70℃ 2 2.5mA 250nA 2V~36V 36V 5mV 5nA Fail-safe function Open-drain SOP-8 Comparators ROHSMSKSEMIComparatorsLM7805
TO-2630℃~+125℃ 1 1A 20V 2V 42uV 5V 62dB@(120Hz) 8mA Fixed Over Temperature Protection、Short Circuit Protection Positive TO-263 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSYONGYUTAIVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLM7812
TO-263TO-263 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSYONGYUTAIUncategorisedBC546
TO-921 NPN 100mA 100nA 300MHz 500mW 65V 6V 800 90mV、250mV NPN TO-92 Bipolar (BJT) ROHSDDFBipolar (BJT)BD140
TO-126-65℃~+150℃ 1 PNP 1.25W 1.5A 100nA 500mV 5V 63 80V PNP TO-126 Bipolar (BJT) ROHSSTMicroelectronicsBipolar (BJT)TL431
SOT-23-20℃~+85℃ 150mA 1mA 2.5V~36V 50ppm/℃ Adjustable Parallel Temperature compensation control ±1% SOT-23 Voltage Reference ROHSGuangdong HottechVoltage Reference
README
README.mdSimple and Affordable Linear Power Supply (0-30V, 0-3A)
This repository accompanies a video about this power supply: https://youtu.be/LigN5W8R_zc
Disclaimer
This design is provided for educational and DIY purposes. Building a linear power supply involves potentially hazardous voltages and significant heat dissipation. Ensure that the transformer, rectifier, pass transistors, heatsinks, wiring, fusing, and enclosure are appropriately rated for your intended application.
Always take appropriate electrical safety precautions when building and testing the power supply.
This LPS is based on Simple and Affordable Power Supply v17: https://forum.cxem.net/topic/76820-%D0%BF%D1%80%D0%BE%D1%81%D1%82%D0%BE%D0%B9-%D0%B8-%D0%B4%D0%BE%D1%81%D1%82%D1%83%D0%BF%D0%BD%D1%8B%D0%B9-%D0%B1%D0%BF-050-%D0%B2/
My version is designed for an adjustable output voltage of 0-30 V and an output current of 0-3 A. However, the design can be easily adapted to achieve significantly higher output voltage and current ratings, depending on the transformer, power components, cooling, and other design considerations.
Features
- Constant Voltage (CV) mode - regulates the output voltage.
- Constant Current (CC) mode - regulates the output current.
- Latching overcurrent protection - shuts down the output when an overcurrent condition occurs and remains latched until reset.
- Overtemperature protection (OTP) - protects the power supply against excessive temperature.
- Transformer tap selector - selects the appropriate transformer winding tap to improve efficiency and reduce power dissipation.
- Four-layer PCB - a four-layer printed circuit board designed to accommodate the circuit and its layout requirements.
Important Note on Circuit Stability
The circuit may be prone to oscillation if inappropriate compensation capacitors are used around the operational amplifiers. The values and placement of these capacitors are important for ensuring stable operation. Do not change the compensation capacitor values without carefully evaluating circuit stability. If modifying the design, verify its behavior under different operating conditions and loads, preferably using an oscilloscope.
Project Files
This repository includes the KiCad project files:
.kicad_pro- project configuration..kicad_sch- schematic..kicad_pcb- PCB layout.
and Gerber files: Gerber.zip
The PCB is 150 x 100 mm, 4 layers, THT + SMD components.
Parts
97| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R11, R20, R21, R24, R31, R42 |
| 6 | 1k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R1, R2, R6, R14, R16, R18 |
| 4 | 1N4007 | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D4, D5, D7, D8 |
| 4 | 1N4148 | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D9, D10, D11, D12 |
| 3 | 1000uF | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C5, C7, C9 |
| 3 | 100k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R3, R4, R34 |
| 3 | 10k | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | R7, R8, R43 |
| 3 | 20k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R22, R32, R33 |
| 3 | 2k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R25, R37, R38 |
| 2 | 1.2k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R12, R13 |
| 2 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C11, C15 |
| 2 | 10k | Potentiometer_THT:Potentiometer_Piher_PC-16_Single_Horizontal | R27, R35 |
| 2 | 1N5408 | Diode_THT:D_DO-201AD_P15.24mm_Horizontal | D6, D13 |
| 2 | 1u SMD | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C8, C14 |
| 2 | 33k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R28, R44 |
| 2 | BC546 | Package_TO_SOT_THT:TO-92_Inline | Q1, Q3 |
| 2 | GND | Connector_Pin:Pin_D1.0mm_L10.0mm | J6, J8 |
| 1 | +12V | Connector_Pin:Pin_D1.0mm_L10.0mm | J5 |
| 1 | +5V | Connector_Pin:Pin_D1.0mm_L10.0mm | J7 |
| 1 | 0.3 6W | Resistor_THT:R_Axial_Power_L25.0mm_W9.0mm_P27.94mm | R36 |
| 1 | 1.8k 0,25W(4.3k 1W) | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R9 |
| 1 | 100n | Capacitor_THT:C_Rect_L13.0mm_W5.0mm_P10.00mm_FKS3_FKP3_MKS4 | C2 |
| 1 | 10k | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R40 |
| 1 | 10k | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | R41 |
| 1 | 10n | Capacitor_THT:C_Rect_L13.0mm_W5.0mm_P10.00mm_FKS3_FKP3_MKS4 | C4 |
| 1 | 10uF | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C12 |
| 1 | 15k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R17 |
| 1 | 15k(39k) | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R23 |
| 1 | 1k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R19 |
| 1 | 1k | Potentiometer_THT:Potentiometer_Piher_PC-16_Single_Horizontal | R26 |
| 1 | 1n SMD | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C6 |
| 1 | 1u | Capacitor_THT:C_Rect_L13.0mm_W5.0mm_P10.00mm_FKS3_FKP3_MKS4 | C13 |
| 1 | 1uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C3 |
| 1 | 200 | Capacitor_THT:C_Rect_L7.0mm_W2.5mm_P5.00mm | C10 |
| 1 | 2k | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | R30 |
| 1 | 39k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R10 |
| 1 | 3k 0.5W (5.6k 1W) | Resistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P15.24mm_Horizontal | R15 |
| 1 | 470k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R39 |
| 1 | 6800uF | Capacitor_THT:CP_Radial_D35.0mm_P10.00mm_SnapIn | C1 |
| 1 | 6k8 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R5 |
| 1 | 9.1k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R29 |
| 1 | BD140 | Package_TO_SOT_THT:TO-126-3_Vertical | Q2 |
| 1 | In | Connector_Wire:SolderWire-1sqmm_1x02_P5.4mm_D1.4mm_OD2.7mm | J3 |
| 1 | In_Misc | Connector_Wire:SolderWire-1sqmm_1x02_P5.4mm_D1.4mm_OD2.7mm | J4 |
| 1 | Jumper | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_Vertical | JP1 |
| 1 | LED GREEN | LED_THT:LED_D3.0mm_IRBlack | D2 |
| 1 | LED ORANGE | LED_THT:LED_D3.0mm_IRBlack | D14 |
| 1 | LED RED | LED_THT:LED_D3.0mm_IRBlack | D3 |
| 1 | LM324 | Package_DIP:DIP-14_W7.62mm_LongPads | U2 |
| 1 | LM393 | Package_DIP:DIP-8_W7.62mm_LongPads | U1 |
| 1 | LM7805 | Package_TO_SOT_THT:TO-220-3_Vertical | U3 |
| 1 | LM7812 | Package_TO_SOT_THT:TO-220-3_Vertical | U4 |
| 1 | Out | Connector_Wire:SolderWire-1sqmm_1x02_P5.4mm_D1.4mm_OD2.7mm | J10 |
| 1 | Relay1 | Connector_Pin:Pin_D1.0mm_L10.0mm | Rel1 |
| 1 | Relay2 | Connector_Pin:Pin_D1.0mm_L10.0mm | Rel2 |
| 1 | TIP3055G | Package_TO_SOT_THT:TO-247-3_Vertical | Q4 |
| 1 | TL431 | Package_TO_SOT_THT:TO-92_Inline | D1 |
| 1 | To_Voltmeter | Connector_Pin:Pin_D1.0mm_L10.0mm | J9 |
| 1 | ~ | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | S1 |
The 93 most common of 97 parts.
Similar boards
- 2 layers256.5 × 172.9 mm

- 2 layers81 × 150 mm

- 2 layers170.2 × 137.2 mm

MCS19
ZeniteSolar/MCS19
Módulo de Carregamento do Sistema da embarcação solar Guarapuvu II (Zênite Solar)
160 parts1GPL-3.0 - 2 layers135.8 × 56.1 mm

Power board
xtarke/automated_buggy
This shield connects microcontroller (MSP-EXP430FR2355) pins to the car's power board. Go to Power Board for more hardware information.
87 parts5GPL-3.0 - 2 layers68 × 87.5 mm

211201062 Faz4 KiCad
alpnak/Analog_Common_Emitter_Amplifier
4-Stage analog common emitter amplifier design and analysis with LTspice & KiCad
46 parts - 2 layers190 × 144.3 mm

Amplifier
oselcukyatagan/CLASS_AB_AUDIO_POWER_AMP
This is the repository for the developing of the class AB audio power amplifier device.
85 parts - 4 layers149.2 × 185.3 mm

Amplifier
scout-cc/SkripsieProject
Designs and reports for personal final year engineering project
239 parts - 2 layers95.3 × 58.4 mm

Questions
How big is the Ultimate LPS PCB?
It measures 150 × 100 mm and has 4 copper layers, 1.66 mm thick.
What parts does the Ultimate LPS use?
97 parts, built around the LM324, LM393, LM7805 and LM7812. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Ultimate LPS KiCad files?
From the BTTLab/simple_and_affordable_lps repository on GitHub, at the commit this page was made from: the board is Ultimate_LPS/Ultimate_LPS.kicad_pcb and its schematic Ultimate_LPS/Ultimate_LPS.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Ultimate LPS design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).