
Three phase bridge
arcoslab/open-coroco-legacy
COmpliant RObot COntroller is a free software project aiming to create an impedance controller based on a stm32 microcontroller using bldc motors and strain gauges.

Firmware designed in ESP32 DEVKIT microcontroller where motor, throttle, breaks, Nextion touch screen and more systems are integrated.
Controller bldc is an open-source printed circuit board by david8128, from the david8128/Electeam-Sharky repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 210 × 125 mm with 73 parts on 61 nets.
It is built around the IR2103PBF, MC1458P and IRF1010NPBF, with the 1N4728A, LM35 and PN2222A among its other parts. Its parts include 29 resistors, 13 capacitors, 9 diodes, 7 ICs and 7 transistors. It belongs with the robots and motor control boards and the ESP32 boards of this library.
This is the firmware for the ESP32-WROOM-32 microcontroller where throttle, break, LCD screen, motor and more systems are integrated.
The PCB Kicad folder is located in (controller_bldc_kicad_Sch_PCB/)[https://github.com/david8128/Electeam-Sharky-ESP32/tree/main/controller_bldc_kicad_Sch_PCB]
Relay for the Operator Presence Control - aka. Death Man Security System (HAT901 12VDC 20A) = 0.96 W
MOSFET has been considered for de OPC but the consumtion is higher (Using IRF1010N with a ) For this project is used the MCPWM BLDC motor control (hall sensor feedback) example from ESP-IDF library.
As shown in Schematic there were used two LM2596 DC-DC HW-411 converters
When battery is fully charged the voltage is 40.6V. The BMS open the discharging circuit when the battery voltage is under 32V.
The energy or maximum energetic storage capacity of the battery is 320Wh.
This modes will be reviewed under the light of the Shell Echo Marathon Competition.
Here you have the documentation of the MCPWM-Hall_Sensor example:
This example will show you how to use MCPWM module to control bldc motor with hall sensor feedback
The following examples uses MCPWM module to control bldc motor and vary its speed continuously
The bldc motor used for testing this code had hall sensor capture sequence of 6-->4-->5-->1-->3-->2-->6-->4--> and so on
IR2103 3-ph bridge driver is used for testing this example code
User needs to make changes according to the motor and gate driver ic used
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R5, R6, R7, R8, R9, R10 |
| 4 | 1.5k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R12, R13, R14, R15 |
| 4 | 1N4004 | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D1, D2, D3, D9 |
| 3 | 0.1uF | Capacitor_THT:C_Disc_D4.7mm_W2.5mm_P5.00mm | C7, C8, C9 |
| 3 | 15k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R20, R21, R22 |
| 3 | 1N4148 | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D6, D7, D8 |
| 3 | 2.2uF | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C2, C3, C4 |
| 3 | 2.5k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R26, R27, R29 |
| 3 | 220uF | Capacitor_SMD:CP_Elec_10x14.3 | C10, C11, C12 |
| 3 | IR2103 | Package_SO:SO-8_3.9x4.9mm_P1.27mm | U4, U8, U9 |
| 3 | IRF1010N | Package_TO_SOT_THT_Electeam:TO-220-3_Horizontal_TabDown | Q1, Q3, Q5 |
| 3 | IRF1010N | Package_TO_SOT_THT_Electeam:TO-220-3_Horizontal_TabUp | Q2, Q4, Q6 |
| 2 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R4, R16 |
| 2 | 1N4728A | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D4, D5 |
| 2 | 1k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2, R3 |
| 1 | 0.1 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R11 |
| 1 | 0.1uF | Capacitor_THT:C_Disc_D7.5mm_W5.0mm_P10.00mm | C13 |
| 1 | 0.47uF | Capacitor_THT:C_Disc_D7.5mm_W5.0mm_P10.00mm | C5 |
| 1 | 1.2k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R28 |
| 1 | 12k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1 |
| 1 | 150k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R23 |
| 1 | 1uF | Capacitor_THT:C_Disc_D7.5mm_W5.0mm_P10.00mm | C1 |
| 1 | 220 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R18 |
| 1 | 2k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R25 |
| 1 | 4.7k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R19 |
| 1 | 47uF | Capacitor_THT:CP_Radial_D8.0mm_P3.80mm | C6 |
| 1 | 5.2k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R17 |
| 1 | 75k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R24 |
| 1 | BLDC Motor | Connector_Phoenix_GMSTB:PhoenixContact_GMSTBA_2,5_3-G-7,62_1x03_P7.62mm_Horizontal | J9 |
| 1 | Battery Supply | Connector_Phoenix_GMSTB:PhoenixContact_GMSTBA_2,5_2-G_1x02_P7.50mm_Horizontal | J1 |
| 1 | Conn_01x11_Male | Connector_Molex:Molex_KK-254_AE-6410-11A_1x11_P2.54mm_Vertical | J2 |
| 1 | ESP32-DEVKITC-32D | ESP32-DEVKITC-32D_Electeam:MODULE_ESP32-DEVKITC-32D | U1 |
| 1 | Fuse | Package_TO_SOT_THT_Electeam:Portafusible | F1 |
| 1 | Hall Sensors | Connector_Molex:Molex_KK-254_AE-6410-05A_1x05_P2.54mm_Vertical | J7 |
| 1 | LM2596SOURCE | Package_TO_SOT_THT_Electeam:LM2596DCSource_Electeam | U5 |
| 1 | LM2596SOURCE_Pin2 | Package_TO_SOT_THT_Electeam:LM2596DCSourcePin2_Electeam | U3 |
| 1 | LM35 | Connector_Molex:Molex_KK-254_AE-6410-03A_1x03_P2.54mm_Vertical | J6 |
| 1 | MC1458P | Package_DIP:DIP-8_W7.62mm_LongPads | U2 |
| 1 | ON_OFF | Connector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | SW1 |
| 1 | PN2222A | Package_TO_SOT_THT:TO-92_Inline | Q7 |
| 1 | RAYEX-L90B | Relay_THT:Relay_SPST_RAYEX-L90B | K1 |

arcoslab/open-coroco-legacy
COmpliant RObot COntroller is a free software project aiming to create an impedance controller based on a stm32 microcontroller using bldc motors and strain gauges.

palazzol/CyberamicControlCenter
Repo for docs and info about the Cyberamic Control Center




KerimAltuntecim/esp32-pcb-control-system
ESP32-C3 PCB control system with Nextion HMI, motor, sensor and power-driver interfaces.


SalihAyvaci21/ESCTasarim
Drone motorları için geliştirilmiş; ATmega328P ve IR2103 tabanlı, sandviç PCB yapısına (2x2 katman) sahip, IRLZ44N MOSFET'li yüksek akım 3-faz BLDC motor sürücüsü.
It measures 210 × 125 mm and has 2 copper layers, 1.6 mm thick.
73 parts, built around the IR2103PBF, MC1458P, IRF1010NPBF and 1N4728A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the david8128/Electeam-Sharky repository on GitHub, at the commit this page was made from: the board is Diseño Electrónico/Esquema y Gerbers PCB/controller_bldc.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).